This work used plasma-enhanced chemical vapor deposition (PECVD) at low temperatures to deposit a silicon nitride layer on multicrystalline silicon (mc-Si), both with and without porous silicon, in ...an attempt to enhance the multicrystalline silicon’s properties for solar cell applications. Silicon nitride has been successfully tested as a passivation and antireflection film in mc-Si. Consequently, reflectance is reduced from 40 to 7% in the 300–1200 nm wavelength range due to the change in the silicon’s morphology, while the effective carrier lifetime value for the Si substrate rose from 8 µs to 71 µs following SiN
x
treatment, thus benefitting a solar cell. A laser beam-induced current (LBIC) also revealed an improvement in the diffusion length of minority carriers, with it rising from 150 µm to 432 µm following SiN
x
treatment. Excellent results were also observed after combining porous silicon with a SiN
x
thin film, it increased the effective carrier lifetime to 104 µs, the diffusion length to 676 µm, the reflectance reduced to 3%, and the surface recombination velocity reduced to 1.6 cm/s. The obtained results therefore suggest that PECVD-based silicon-nitride-covered porous silicon shows promise in terms of cost-effectiveness and efficiency, thus helping to advance solar cell technology.
Full text
Available for:
EMUNI, FIS, FZAB, GEOZS, GIS, IJS, IMTLJ, KILJ, KISLJ, MFDPS, NLZOH, NUK, OILJ, PNG, SAZU, SBCE, SBJE, SBMB, SBNM, UKNU, UL, UM, UPUK, VKSCE, ZAGLJ
An exploration is made to investigate numerically and theoretically the time dependent flow of blood along with heat transfer through abnormal artery having trapezoidal shaped plaque. The flow is ...taken to be Newtonian, laminar, unsteady and incompressible. A suitable geometrical model is constructed to simulate the trapezoidal stenosis affected artery. The governed 2-dimensional momentum and heat transfer equations are conventionalized by assuming mild trapezoidal stenosis. The renovate partial differential equations are further converted into ordinary differential equations by assist of transformations. The novelty of the work is to consider unsteady blood flow through trapezoidal shape stenosed artery. A technique of finite difference is used to discretize the updated dimensionless model numerically. Comprehensive graphical outcomes for a flow of blood are obtained. The effect of trapezoidal plaque on blood velocity, pressure and temperature are shown by surface graph inside the artery and also shown with the help of line graph.
Full text
Available for:
IZUM, KILJ, NUK, PILJ, PNG, SAZU, UL, UM, UPUK
This work aimed to study one of the most important challenges in orthopaedic implantations, known as stress shielding of total shoulder implants. This problem arises from the elastic modulus mismatch ...between the implant and the surrounding tissue, and can result in bone resorption and implant loosening. This objective was addressed by designing and optimising a cellular-based lattice-structured implant to control the stiffness of a humeral implant stem used in shoulder implant applications. This study used a topology lattice-optimisation tool to create different cellular designs that filled the original design of a shoulder implant, and were further analysed using finite element analysis (FEA). A laser powder bed fusion technique was used to fabricate the Ti-6Al-4V test samples, and the obtained material properties were fed to the FEA model. The optimised cellular design was further fabricated using powder bed fusion, and a compression test was carried out to validate the FEA model. The yield strength, elastic modulus, and surface area/volume ratio of the optimised lattice structure, with a strut diameter of 1 mm, length of 5 mm, and 100% lattice percentage in the design space of the implant model were found to be 200 MPa, 5 GPa, and 3.71 mm
, respectively. The obtained properties indicated that the proposed cellular structure can be effectively applied in total shoulder-replacement surgeries. Ultimately, this approach should lead to improvements in patient mobility, as well as to reducing the need for revision surgeries due to implant loosening.
Full text
Available for:
IZUM, KILJ, NUK, PILJ, PNG, SAZU, UL, UM, UPUK
Computer-aided design (CAD) has become an integral part of engineering education, particularly for those studying mechanical engineering. By providing practical skills that are highly valued in the ...engineering industry, proficiency in CAD systems enhances students’ employability. Generally, CAD systems provide students with the tools and knowledge necessary to excel in their engineering education and future careers. In order to help teachers to give the best training to their students and to make the right evaluations, an automatized tool is needed to support the evaluation of CAD models during training sessions. After an extensive bibliographical search, this paper proposes a CAD Model Automatized Assessment (MAA) Tool for mechanical courses called the CAD MAA Tool. This tool is mainly based on a developed model that takes into account different aspects of modeling, such as geometric, feature-based, and parametric modeling. To correctly evaluate a given part compared to a reference one, the proposed model uses different coefficients fixed by the teacher according to their teaching strategies or course objectives.
Magnesium alloys are still attractive materials for applications that necessitate light weight due to their low density, moderate strength, and good corrosion resistance. AZ91 is one of the widely ...applied magnesium alloys due to its very good castability and strength. However, one of the drawbacks of magnesium alloys is the low elastic modulus. So, reinforcing AZ91 with carbon short fibers with the aim of further increasing the strength and improving the elastic modulus is investigated in this study. Squeeze cast AZ91-23 vol.% carbon short carbon (AZ91-C) and the unreinforced AZ91 are deeply examined by tensile testing at different temperatures (20, 100, 150, 200, 250, and 300 °C). Tensile stress-strain curves are measured and the tensile parameters (yield stress, ultimate tensile strength and strain) are defined and presented against the test temperature. Yield stress of AZ91 at 20 °C (109 MPa) is doubled (226 MPa) in the reinforced AZ91-C. Yield stress is found to slightly decrease with increasing the test temperature. Ultimate tensile strength of AZ91 at 20 °C (198 MPa) is increased (262 MPa) in the reinforced AZ91-C. The improvement of the ultimate tensile strength due to reinforcing increases with increasing the test temperature. Flow curves are determined and described by a modified Mecking-Kocks relationship and the flow parameters are determined and described as a function of the test temperature. Microstructure investigation was undertaken of the fractured tensile specimens at the grain boundaries rich in eutectic structure formed at the grain boundaries. Mixed brittle/ductile fracture mode is detected on the fracture surface of unreinforced AZ91, while the SEM investigations show matrix/carbon fiber detachment and fiber fracture as main fracture modes.
Full text
Available for:
IZUM, KILJ, NUK, PILJ, PNG, SAZU, UL, UM, UPUK
Limb disability is a frequent healthcare problem, especially for patients in primary care. Orthotic treatment has become the most common practice for either rehabilitation or permanent assistance, ...due to the emergence of 3D scanning and 3D printing technologies. A CAD model rebuilt from captured data is a key step in the rapid prototyping process of customized orthoses. An accurate and robust surface reconstruction technique remains a research challenge, aiming for a well-fitting design and the patient’s comfort. Thus, this paper presents of a new 3D curve-based reconstruction algorithm to obtain a precise 3D surface of an orthotic device from a scanned body part. Numerical experiments of two orthosis design case studies are shown to evaluate the reliability and accuracy of the proposed approach compared to other reconstruction methods.
The strength and hardness of the composites were investigated. The present results showed that the strength and hardness of the composites increased with the addition of graphene nanosheets. Graphene ...nanosheets may act as obstacles for the dislocation movement and finally promote for the dislocations accumulation having an important role for the improvement of mechanical properties of the composites. The difference in thermal expansion coefficient was also responsible for the improvement of the strength and hardness of the composites.
The present study is established on a simulation using CFD analysis in COMSOL. Blood acted as the base fluid with this simulation. The taken flow is been modeled as incompressible, unsteady, laminar ...and Newtonian fluid, which is appropriate at high rates of shear. The characteristic of flow of blood is been studied in order to determine pressure, velocity and temperature impact caused by an abdominal aortic aneurysm (AAA). This work employs nanoparticles of the Iron Oxide (Fe3O4) type. The CFD technique is utilized to evaluate the equations of mass, momentum, and energy. The COMSOL software is utilized to generate a normal element sized mesh. The findings of this study demonstrate that velocity alters through aneurysmal part of the aorta, that velocity is higher in a diseased segment, and that velocity increases before and after the aneurysmal region. For the heat transfer feature, the reference temperature and general inward heat flux is taken as 293.15K and 800W/m2. The nanoparticles altered blood's physical properties, including conductivity, dynamic viscosity, specific heat, and density. The inclusion of Iron Oxide (Fe3O4) nanoparticles managed to prevent overheating because taken nanoparticles have significant thermal conductivity. These findings will be extremely beneficial in the treatment of abdominal aortic aneurysm.
Full text
Available for:
GEOZS, IJS, IMTLJ, KILJ, KISLJ, NLZOH, NUK, OILJ, PNG, SAZU, SBCE, SBJE, UILJ, UL, UM, UPCLJ, UPUK, ZAGLJ, ZRSKP
The additive manufacturing (AM) field is rapidly expanding, attracting significant scientific attention. This family of processes will be widely used in the evolution of Industry 4.0, particularly in ...the production of customized components. However, as the complexity and variability of additive manufacturing processes increase, there is an increasing need for advanced techniques to ensure quality control, optimize performance, and reduce production costs. Multiple tests are required to optimize processing variables for specific equipment and processes, to achieve optimum processing conditions. The application of digital twins (DTs) has significantly enhanced the field of additive manufacturing. A digital twin, abbreviated as DT, refers to a computer-generated model that accurately depicts a real-world object, system, or process. A DT comprises the complete additive manufacturing process, from the initial conception phase to the final manufacturing phase. It enables the manufacturing process to be continuously monitored, studied, and optimized in real time. DT has emerged as an important tool in the additive manufacturing industry. They allow manufacturers to enhance the process, improve product quality, decrease costs, and accelerate innovation. However, the development of DT in AM is an iterative and continuous process. It requires collaboration between domain experts, data scientists, engineers, and manufacturing teams to guarantee an accurate representation of the process by the digital twin. This paper aims to provide a comprehensive analysis of the current state of DT for additive manufacturing, examining their applications, benefits, challenges, and future directions.
AZ91 is one of the most broadly used Mg alloys because of its good castability and reasonable mechanical properties. Strengthening AZ91 with carbon short fibers aims to increase tensile and fatigue ...strength, creep, and wear resistance. One of the proposed applications of reinforced AZ91 is the production of pistons for trucks. Such reciprocating parts are subjected to alternating fatigue loads which can lead to fatigue failure. In this respect, studying the tensile and fatigue behavior of materials subjected to such loading conditions is of great interest. The alternating low-cycle fatigue (LCF) and high-cycle fatigue (HCF) of unreinforced AZ91 and carbon fiber-reinforced AZ91 (AZ91-C) were investigated at 20 °C and 250 °C. Tensile tests were carried out at the same testing temperature to find the appropriate fatigue testing stress and strain for stress-controlled and strain-controlled tests, respectively. The fatigue curves of stress against the number of cycles (S–N) revealed that the composite AZ91-C’s fatigue strength was 55 MPa under HCF, while that of the matrix alloy AZ91 was only 37 MPa at 250 °C. Fracture investigations were conducted on the broken test samples. The fracture approach in the matrix material (AZ91) is mixed ductile/brittle containing fatigue serration, fiber fracture, and separation in the reinforced material (AZ91-C).