Soundness of additively manufactured parts depends on a lot of process and geometrical parameters. A wrong process design leads to defects such as lack of fusion or keyhole porosity that have a ...detrimental effect on the mechanical properties of the printed parts. Process parameter optimization is thus a formidable challenge that requires in general a huge amount of experimental data. Among the others, heat source power and scan speed are the most defects-affecting parameters to be optimized. The energy density is used in literature to quantify their combination. Unfortunately, in different works it was demonstrated that it fails if used as design parameter mainly because it does not take into account the material properties and the interaction between heat source and the powder bed. In this contribution, a modified volumetric energy density equation that takes into account the powder-heat source interaction to optimize the combination of power-scan speed values for porosity assessment in powder bed fusion process design is proposed and verified on both AlSi10Mg alloy and Maraging steel 300.
Full text
Available for:
DOBA, EMUNI, FIS, FZAB, GEOZS, GIS, IJS, IMTLJ, IZUM, KILJ, KISLJ, MFDPS, NLZOH, NUK, OBVAL, OILJ, PILJ, PNG, SAZU, SBCE, SBJE, SBMB, SBNM, SIK, UILJ, UKNU, UL, UM, UPUK, VKSCE, ZAGLJ
Improving soft tissue attachment and reducing bacterial colonization on titanium abutments are key factors for the long-term maintenance of healthy soft and hard peri-implant tissues. This in vitro ...study was conducted to compare the biocompatibility and antibacterial activity of four different surfaces: uncoated Ti6Al4V, anodized, and coated with titanium nitride or zirconium nitride. Surface topography was investigated with a high-resolution system for measuring surface finishes. Human gingival fibroblast (HGF) adhesion and proliferation were examined using MTT assay, Scanning Electron Microscopy (SEM) imaging, immunofluorescence analysis and real-time PCR for selected target genes. The hemolysis and AMES tests were performed to assess the chemical compounds' blood compatibility and mutagenic potential, respectively. Antibacterial activity was tested against five bacterial strains isolated from the oral cavity (Streptococcus salivarius, S. sanguinis, S. mutans, S. sobrinus, S. oralis), and the percentage of dead bacteria was calculated. Roughness measurements confirmed a substantial similarity between the surfaces and their compatibility with clinical applications. MTT assay, SEM analysis and immunofluorescence staining showed adhesion and proliferation of HGFs cultured on all the examined surfaces. PCR confirmed that HGFs produced extracellular matrix components efficiently on all the surfaces. No hemolytic activity was detected, and the AMES test confirmed the surfaces' clinical safety. For all tested bacterial strains, biofilms grown on the zirconium nitride surface showed a higher percentage of dead bacteria than on the other disks. The titanium nitride surface inactivated bacterial biofilms, too, but to a lesser extent.
Full text
Available for:
DOBA, IZUM, KILJ, NUK, PILJ, PNG, SAZU, SIK, UILJ, UKNU, UL, UM, UPUK
Compare the accuracy of intraoral digital impression in full-arch implant-supported fixed dental prosthesis acquired with eight different intraoral scanner (Ios).
A polymethyl methacrylate acrylic ...model of an edentulous mandible with six scan-abutment was used as a master model and its dimensions measured with a coordinate measuring machine. Eight different Ios were used to generate digital impression: True Definition, Trios, Cerec Omnicam, 3D progress, CS3500, CS3600, Planmeca Emelard and Dental Wings. Fifteen digital impressions were made. A software called “Scan-abut” was developed to analyse and compare the digital impression with the master model, obtaining the scanning accuracy. The three-dimensional (3D) position and distance analysis were performed.
Mean value of the 3D position analysis showed that the True Definition (31 μm ± 8 μm) and Trios (32 μm ± 5 μm) have the best performance of the group. The Cerec Omnicam (71 μm ± 55 μm), CS3600 (61 μm ± 14 μm) have an average performance. The CS3500 (107 μm ± 28 μm) and Planmeca Emelard (101 μm ± 38 μm) present a middle-low performance, while the 3D progress (344 μm ± 121 μm) and Dental Wings (148 μm ± 64 μm) show the low performance. The 3D distance analysis showed a good linear relationship between the errors and scan-abutment distance only with the True Definition and CS3600.
Not all scanners are suitable for digital impression in full-arch implant-supported fixed dental prosthesis and the weight of the output files is independent from the accuracy of the Ios.
Display omitted
•Fatigue strength was found insensitive to the build relative to scraper direction.•Fatigue strength is highly sensitive to porosity morphology, size and distribution.•In most cases, ...lack of fusion was the killer defect.
Additive manufacturing is an emerging technique that is not only subjected to the interest of academic world because of its peculiar characteristics to obtain new material properties and optimized 3D geometries, but it also finds the interest of the industrial sector because of the possibility to build advanced components never realized until now. Among the additive manufacturing processes, Laser Powder Bed Fusion process is perhaps the most used in producing components out of metallic materials. In particular, thanks to its low density and its hypoeutectic favourable composition, AlSi10Mg alloy is particular suitable for the production of lightweight components by additive manufacturing. However, for safety reasons, their mechanical, static and cyclic, characteristics need to be well understood and predicted. Unfortunately, they are dramatically influenced by process parameters that in turn may promote killer defects dangerous for the fatigue strength of load bearing mechanical components. This contribution is aimed at highlighting the influence of defects on the fatigue resistance of AlSi10Mg samples produced by laser powder bed fusion. The combination of process parameters were obtained that maximizes the fatigue strength and reduces the scattering of the results.
Full text
Available for:
GEOZS, IJS, IMTLJ, KILJ, KISLJ, NLZOH, NUK, OILJ, PNG, SAZU, SBCE, SBJE, UILJ, UL, UM, UPCLJ, UPUK, ZAGLJ, ZRSKP
Purpose: To compare the flexural properties and the adhesion of Lactobacillus salivarius (LS), Streptococcus mutans (SM), and Candida albicans (CA) on heat-polymerized (CV), CAD-CAM milled (CAD), or ...3D-printed (3D) Poly (methylmethacrylate) (PMMA).Methods: Ultimate Flexural Strength (UFS), Flexural Strain (FS) (%) at Flexural Strength, and Flexural Modulus (FM) of specimens (65.0×10.0×3.3 mm) from each PMMA group (n=6) were calculated by using the 3-point bending test. The surface roughness profiles (R) were measured before and after polishing with a contact profilometer. LS, SM, and CA adhesion on PMMA specimens (n=18) (10 mm in diameter, 3 mm in height) was assessed after 90 minutes and 16 hours by using scanning electron microscopy. The Kruskal-Wallis test with post hoc analysis was performed to compare the groups (alpha=0.05).Results: Mean UFS values were 80.79±7.64 MPa for CV, 110.23±5.03 MPa for CAD, and 87.34±6.39 MPa for 3D. Mean FS values were 4.37±1.04% for CV, 4.71±0.62% for CAD, and 6.19±0.13 % for 3D. Mean FM values were 2542±301 MPa for CV, 3435±346 MPa for CAD, and 2371±197 MPa for 3D. CAD had the lowest average R value (0.29±0.16 µm) before polishing, and bacterial adhesion after 90 minutes of incubation. R value and microbial adhesion were not different amongst groups after polishing and 16 hours of incubation, respectively.Conclusion: The CAD group displayed the best flexural properties, except for FS, the lowest roughness before polishing and bacterial adhesion after 90 minutes of incubation. All tested PMMAs had similar surface roughness after polishing, and microbial adhesion after 16 hours of incubation.
Advances in additive manufacturing technologies facilitate the fabrication of cellular materials that have tailored functional characteristics. The application of solid freeform fabrication ...techniques is especially exploited in designing scaffolds for tissue engineering. In this review, firstly, a classification of cellular materials from a geometric point of view is proposed; then, the main approaches on geometric modeling of cellular materials are discussed. Finally, an investigation on porous scaffolds fabricated by additive manufacturing technologies is pointed out. Perspectives in geometric modeling of scaffolds for tissue engineering are also proposed.
Full text
Available for:
FZAB, GIS, IJS, KILJ, NLZOH, NUK, OILJ, SBCE, SBMB, UL, UM, UPUK
In tolerancing activities focusing on the allocation of geometrical tolerances, many critical issues originate from the non-optimal assignment of responsibilities among the organization units ...involved. This paper aims to depict relations between different tolerancing activities and relevant specifications, assigning them to the proper actor and, therefore, expanding the ISO 8015:2011 “responsibility principle”. A classification among tolerancing activities, specifications, and media is proposed; a horizontal hierarchical framework among functional, manufacturing, and verification specifications and a vertical hierarchical framework along the supply chain are discussed. Examples of both hierarchical structures are presented.
Additive Manufacturing (AM) brought a revolution in parts design and production. It enables the possibility to obtain objects with complex geometries and to exploit structural optimization ...algorithms. Nevertheless, AM is far from being a mature technology and advances are still needed from different perspectives. Among these, the literature highlights the need of improving the frameworks that describe the design process and taking full advantage of the possibilities offered by AM. This work aims to propose a workflow for AM guiding the designer during the embodiment design phase, from the engineering requirements to the production of the final part. The main aspects are the optimization of the dimensions and the topology of the parts, to take into consideration functional and manufacturing requirements, and to validate the geometric model by computer-aided engineering software. Moreover, a case study dealing with the redesign of a piston rod is presented, in which the proposed workflow is adopted. Results show the effectiveness of the workflow when applied to cases in which structural optimization could bring an advantage in the design of a part and the pros and cons of the choices made during the design phases were highlighted.
The purpose of this study was to investigate the marginal precision of computer numeric control-milled frameworks fabricated of grade 4 commercially pure titanium or cobalt-chrome alloy through ...digital technology and to compare them with conventional cast frameworks.
A titanium cast of a mandibular arch with six implant analogs was used as a master. The master cast was measured with a coordinate measuring machine. Fifteen rigid anatomic frameworks were created on the master cast in cast gold alloy and milled in titanium or cobalt-chrome material. The fifteen anatomic frameworks were measured in the same manner as the master cast. While the milled frameworks were measured once, at the end of the milling process, the cast anatomic frameworks were measured twice: immediately after the casting and divesting procedures and again after a technical adaptation procedure. Each anatomic framework was weighed. To compare the measurements obtained from each group of frameworks, descriptive statistics were calculated and one-way analysis of variance was performed, with values considered statistically significant at P < .05.
The mean weight of the cast frameworks was 33.41 g, the cobalt-chrome frameworks weighed 18.12 g on average, and the titanium frameworks averaged 8.7 g. The mean values for three-dimensional deviation of the center point position for each group of frameworks were 261 μm (cast frameworks before adaptation), 49 μm (cast frameworks after adaptation), 26 μm (milled frameworks in cobalt-chrome), and 26 μm (milled frameworks in titanium).
Within the limitations of this in vitro study, absolute passive fit cannot be achieved, regardless of material and fabrication technique. Anatomic milled frameworks fabricated in titanium or cobalt-chrome presented reduced center point deviation compared to cast frameworks. Titanium frameworks weighed less than cobalt-chrome and cast gold alloy frameworks.
Material extrusion additive manufacturing enables us to combine more materials in the same nozzle during the deposition process. This technology, called material coextrusion, generates an expanded ...range of material properties, which can gradually change in the design domain, ensuring blending or higher bonding/interlocking among the different materials. To exploit the opportunities offered by these technologies, it is necessary to know the behavior of the combined materials according to the materials fractions. In this work, two compatible pairs of materials, namely Polylactic Acid (PLA)-Thermoplastic Polyurethane (TPU) and Acrylonitrile Styrene Acrylate (ASA)-TPU, were investigated by changing the material fractions in the coextrusion process. An original model describing the distribution of the materials is proposed. Based on this, the mechanical properties were investigated by analytical and numerical approaches. The analytical model was developed on the simplified assumption that the coextruded materials are a set of rods, whereas the more realistic numerical model is based on homogenization theory, adopting the finite element analysis of a representative volume element. To verify the deposition model, a specific experimental test was developed, and the modeled material deposition was superimposed and qualitatively compared with the actual microscope images regarding the different deposition directions and material fractions. The analytical and numerical models show similar trends, and it can be assumed that the finite element model has a more realistic behavior due to the higher accuracy of the model description. The elastic moduli obtained by the models was verified in experimental tensile tests. The tensile tests show Young's moduli of 3425 MPa for PLA, 1812 MPa for ASA, and 162 MPa for TPU. At the intermediate material fraction, the Young's modulus shows an almost linear trend between PLA and TPU and between ASA and TPU. The ultimate tensile strength values are 63.9 MPa for PLA, 35.7 MPa for ASA, and 63.5 MPa for TPU, whereas at the intermediate material fraction, they assume lower values. In this initial work, the results show a good agreement between models and experiments, providing useful tools for designers and contributing to a new branch in additive manufacturing research.
Full text
Available for:
IZUM, KILJ, NUK, PILJ, PNG, SAZU, UL, UM, UPUK