Engineered cementitious composite (ECC) featuring extraordinary tensile ductility is a promising option for many structural applications but its large-scale manufacture is not eco-friendly due to its ...binding ingredient, Portland cement. One of the potential alternatives to ECC is engineered geopolymer composites (EGC) that have been increasingly studied in recent years. This paper presents a comprehensive review of the state-of-the-art of EGC in terms of design theory, mix design, fabrication process, engineering properties, durability and environmental benefit, with special focus on the effects of different material composition factors including precursor, activator, aggregate, additive and fibre on the critical material properties of EGC especially uniaxial tensile properties. The correlations between essential mechanical properties are discussed in depth. The unique tensile behaviour of EGC can be tailored by modifying the material composition that would change its internal microstructure and in turn alter the matrix properties and fibre-matrix interfacial behaviour. Compared to typical ECC, around 64% of EGC mixtures have higher tensile strain capacity (over 2.49%) and about 27% of mixtures exhibit larger tensile strength (over 4.86 MPa). Through adjusting the mix design of EGC, it holds promises as a cost-effective and sustainable material for applications against dynamic loadings, fire and chemical attacks, as well as 3D concrete printing. This review summarises the recent advances in EGC and identifies the remaining challenges in development of EGC with desired properties for practical applications.
Full text
Available for:
GEOZS, IJS, IMTLJ, KILJ, KISLJ, NLZOH, NUK, OILJ, PNG, SAZU, SBCE, SBJE, UILJ, UL, UM, UPCLJ, UPUK, ZAGLJ, ZRSKP
Understanding the dielectric breakdown behavior of polymer nanocomposites is crucial to the design of high‐energy‐density dielectric materials with reliable performances. It is however challenging to ...predict the breakdown behavior due to the complicated factors involved in this highly nonequilibrium process. In this work, a comprehensive phase‐field model is developed to investigate the breakdown behavior of polymer nanocomposites under electrostatic stimuli. It is found that the breakdown strength and path significantly depend on the microstructure of the nanocomposite. The predicted breakdown strengths for polymer nanocomposites with specific microstructures agree with existing experimental measurements. Using this phase‐field model, a high throughput calculation is performed to seek the optimal microstructure. Based on the high‐throughput calculation, a sandwich microstructure for PVDF–BaTiO3 nanocomposite is designed, where the upper and lower layers are filled with parallel nanosheets and the middle layer is filled with vertical nanofibers. It has an enhanced energy density of 2.44 times that of the pure PVDF polymer. The present work provides a computational approach for understanding the electrostatic breakdown, and it is expected to stimulate future experimental efforts on synthesizing polymer nanocomposites with novel microstructures to achieve high performances.
A comprehensive phase‐field model is developed to investigate the breakdown behavior of polymer nanocomposites with different microstructures under electrostatic stimuli, whose results agree with existing experimental measurements. Based on the phase‐field model, a high throughput calculation is performed to design and optimize a sandwich microstructure for PVDF–BaTiO3 nanocomposites, obtaining an enhanced energy density of 2.44 times than that of the pure polymer.
Full text
Available for:
BFBNIB, FZAB, GIS, IJS, KILJ, NLZOH, NUK, OILJ, SAZU, SBCE, SBMB, UL, UM, UPUK
Understanding the breakdown mechanisms of polymer-based dielectrics is critical to achieving high-density energy storage. Here a comprehensive phase-field model is developed to investigate the ...electric, thermal, and mechanical effects in the breakdown process of polymer-based dielectrics. High-throughput simulations are performed for the P(VDF-HFP)-based nanocomposites filled with nanoparticles of different properties. Machine learning is conducted on the database from the high-throughput simulations to produce an analytical expression for the breakdown strength, which is verified by targeted experimental measurements and can be used to semiquantitatively predict the breakdown strength of the P(VDF-HFP)-based nanocomposites. The present work provides fundamental insights to the breakdown mechanisms of polymer nanocomposite dielectrics and establishes a powerful theoretical framework of materials design for optimizing their breakdown strength and thus maximizing their energy storage by screening suitable nanofillers. It can potentially be extended to optimize the performances of other types of materials such as thermoelectrics and solid electrolytes.
Impossible voltage plateau regulation for the cathode materials with fixed active elemental center is a pressing issue hindering the development of Na‐superionic‐conductor (NASICON)‐type ...Na3V2(PO4)2F3 (NVPF) cathodes in sodium‐ion batteries (SIBs). Herein, a high‐entropy substitution strategy, to alter the detailed crystal structure of NVPF without changing the central active V atom, is pioneeringly utilized, achieving simultaneous electronic conductivity enhancement and diffusion barrier reduction for Na+, according to theoretical calculations. The as‐prepared carbon‐free high‐entropy Na3V1.9(Ca,Mg,Al,Cr,Mn)0.1(PO4)2F3 (HE‐NVPF) cathode can deliver higher mean voltage of 3.81 V and more advantageous energy density up to 445.5 Wh kg−1, which is attributed by the diverse transition‐metal elemental substitution in high‐entropy crystalline. More importantly, high‐entropy introduction can help realize disordered rearrangement of Na+ at Na(2) active sites, thereby to refrain from unfavorable discharging behaviors at low‐voltage region, further lifting up the mean working voltage to realize a full Na‐ion storage at the high voltage plateau. Coupling with a hard carbon (HC) anode, HE‐NVPF//HC SIB full cells can deliver high specific energy density of 326.8 Wh kg−1 at 5 C with the power density of 2178.9 W kg−1. This route means the unlikely potential regulation in NASICON‐type crystal with unchangeable active center becomes possible, inspiring new ideas on elevating the mean working voltage for SIB cathodes.
A high‐entropy effect is delicately introduced into fluorophosphate cathode for sodium‐ion batteries by in situ partial substitution of active V central atom, preparing a high‐entropy carbon‐free Na3V1.9(Ca,Mg,Al,Cr,Mn)0.1(PO4)2F3 cathode, suppressing the occurrence of detrimental phase transition process in the low‐voltage region, and further lifting up the mean working voltage of pristine Na3V2(PO4)2F3, enhancing sodium storage behavior, rate capability, and cycle performance.
Full text
Available for:
BFBNIB, FZAB, GIS, IJS, KILJ, NLZOH, NUK, OILJ, SAZU, SBCE, SBMB, UL, UM, UPUK
The MYB proteins comprise one of the largest families of transcription factors (TFs) in plants. Although several MYB genes have been characterized to play roles in secondary metabolism, the MYB ...family has not yet been identified in apple. In this study, 229 apple MYB genes were identified through a genome-wide analysis and divided into 45 subgroups. A computational analysis was conducted using the apple genomic database to yield a complete overview of the MYB family, including the intron-exon organizations, the sequence features of the MYB DNA-binding domains, the carboxy-terminal motifs, and the chromosomal locations. Subsequently, the expression of 18 MYB genes, including 12 were chosen from stress-related subgroups, while another 6 ones from other subgroups, in response to various abiotic stresses was examined. It was found that several of these MYB genes, particularly MdoMYB121, were induced by multiple stresses. The MdoMYB121 was then further functionally characterized. Its predicted protein was found to be localized in the nucleus. A transgenic analysis indicated that the overexpression of the MdoMYB121 gene remarkably enhanced the tolerance to high salinity, drought, and cold stresses in transgenic tomato and apple plants. Our results indicate that the MYB genes are highly conserved in plant species and that MdoMYB121 can be used as a target gene in genetic engineering approaches to improve the tolerance of plants to multiple abiotic stresses.
Full text
Available for:
DOBA, IZUM, KILJ, NUK, PILJ, PNG, SAZU, SIK, UILJ, UKNU, UL, UM, UPUK
Acoustic Emission (AE) waveforms contain information on microscopic structural features that can be related with damage of coal rock masses. In this paper, the Hilbert-Huang transform (HHT) method is ...used to obtain detailed structural characteristics of coal rock masses associated with damage, at different loading stages, from the analyses of the characteristics of AE waveforms. The results show that the HHT method can be used to decompose the target waveform into multiple intrinsic mode function (IMF) components, with the energy mainly concentrated in the
C
1
–
C
4
IMF components, where the
C
1
component has the highest frequency and the largest amount of energy. As the loading continues, the proportion of energy occupied by the low-frequency IMF component shows an increasing trend. In the initial compaction stage, the Hilbert marginal spectrum is mainly concentrated in the low frequency range of 0–40 kHz. The plastic deformation stage is associated to energy accumulation in the frequency range of 0–25 kHz and 200–350 kHz, while the instability damage stage is mainly concentrated in the frequency range of 0–25 kHz. At 20 kHz, the instability damage reaches its maximum value. There is a relatively clear instantaneous energy peak at each stage, albeit being more distinct at the beginning and at the end of the compaction phase. Since the effective duration of the waveform is short, its resulting energy is small, and so there is a relatively high value from the instantaneous energy peak. The waveform lasts a relatively long time after the peak that coincides with failure, which is the period where the waveform reaches its maximum energy level. The Hilbert three-dimensional energy spectrum is generally zero in the region where the real energy is zero. In addition, its energy spectrum is intermittent rather than continuous. It is therefore consistent with the characteristics of the several dynamic ranges mentioned above, and it indicates more clearly the low-frequency energy concentration in the critical stage of instability failure. This study well reflects the response law of geophysical signals in the process of coal rock instability and failure, providing a basis for monitoring coal rock dynamic disasters.
Full text
Available for:
EMUNI, FIS, FZAB, GEOZS, GIS, IJS, IMTLJ, KILJ, KISLJ, MFDPS, NLZOH, NUK, OILJ, PNG, SAZU, SBCE, SBJE, SBMB, SBNM, UKNU, UL, UM, UPUK, VKSCE, ZAGLJ
As context is important to gene expression, so is the preprocessing of microarray to transcriptomics. Microarray data suffers from several normalization and significance problems. Arbitrary fold ...change (FC) cut-offs of >2 and significance p-values of <0.02 lead data collection to look only at genes which vary wildly amongst other genes. Therefore, questions arise as to whether the biology or the statistical cutoff are more important within the interpretation. In this paper, we reanalyzed a zebrafish (D. rerio) microarray data set using GeneSpring and different differential gene expression cut-offs and found the data interpretation was drastically different. Furthermore, despite the advances in microarray technology, the array captures a large portion of genes known but yet still leaving large voids in the number of genes assayed, such as leptin a pleiotropic hormone directly related to hypoxia-induced angiogenesis.
The data strongly suggests that the number of differentially expressed genes is more up-regulated than down-regulated, with many genes indicating conserved signalling to previously known functions. Recapitulated data from Marques et al. (2008) was similar but surprisingly different with some genes showing unexpected signalling which may be a product of tissue (heart) or that the intended response was transient.
Our analyses suggest that based on the chosen statistical or fold change cut-off; microarray analysis can provide essentially more than one answer, implying data interpretation as more of an art than a science, with follow up gene expression studies a must. Furthermore, gene chip annotation and development needs to maintain pace with not only new genomes being sequenced but also novel genes that are crucial to the overall gene chips interpretation.
Full text
Available for:
DOBA, IZUM, KILJ, NUK, PILJ, PNG, SAZU, SIK, UILJ, UKNU, UL, UM, UPUK
The Roles of CD73 in Cancer Gao, Zhao-wei; Dong, Ke; Zhang, Hui-zhong
BioMed research international,
01/2014, Volume:
2014
Journal Article
Peer reviewed
Open access
Purinergic signaling has emerged as an important player in cancer progression and is regulated by a series of nucleotidases. Among the enzyme cascade, CD73, which catelyzes AMP breakdown to ...adenosine, has been found to be overexpressed in many types of cancer. Various factors and mechanisms are employed to regulate expression of CD73. Accumulating studies have shown that CD73 is a key regulatory molecule of cancer cells proliferation, migration and invasion in vitro, tumor angiogenesis, and tumor immune escape in vivo. With such important roles in cancer, CD73 has become an appealing therapy target. Recent evidences in mice models demonstrated that targeted blockade of CD73 could be a favorable therapeutic approach for cancer patients in the future. In this review, we will summarize the multiple roles of CD73 in cancer development, including its clinical significance, its promotive effects on tumor growth, metastasis, and angiogenesis, and its suppressive effects on immune response, regulatory mechanisms of CD73 expression, and current situation of anti-CD73 cancer therapy.
Full text
Available for:
DOBA, FZAB, GIS, IJS, IZUM, KILJ, NLZOH, NUK, OILJ, PILJ, PNG, SAZU, SBCE, SBMB, SIK, UILJ, UKNU, UL, UM, UPUK, VSZLJ
MicroRNAs (miRs) are involved in lymphoma progression by regulating tumor cell interaction with microenvironment. MiR155 is overexpressed in diffuse large B-cell lymphoma (DLBCL) and its biological ...effect on tumor microenvironment needs to be futher investigated.
MiR155 was detected by quantitative real-time PCR in patients with newly diagnosed DLBCL. The mechanism of action of miR155 on lymphoma progression and tumor microenvironment was examined in vitro in B-lymphoma cell lines and in vivo in a murine xenograft model.
Serum miR155 was significantly elevated, correlated with tumor miR155 expression, and indicated poor disease outcome in DLBCL. MiR155 overexpression was associated with decreased peripheral blood CD8+T cells and inhibition of T-cell receptor signaling. Of note, EBV-positive patients showed higher serum miR155 than EBV-negative patients. In co-culture systems of B-lymphoma cells with immune cells, miR155 induced Fas-mediated apoptosis of CD8+T cells, which could be targeted by anti-PD-1 and anti-PD-L1 antibodies. Moreover, miR155 enhanced lymphoma cell PD-L1 expression, recruited CD8+T cells by PD-1/PD-L1 interaction and inhibited CD8+T cell function via dephosphorylating AKT and ERK. MiR155-induced AKT/ERK inactivation was more obvious in CD8+T cells co-cultured with EBV-infected B-lymphoma cells. In vivo in a murine xenograft model established with subcutaneous injection of A20 cells, PD-L1 blockade particularly retarded miR155-overexpressing tumor growth, consistent with maintenance of CD8+T cells and their function.
As a oncogenic biomarker of B-cell lymphoma, serum miR155 was related to lymphoma progression through modulating PD-1/PD-L1-mediated interaction with CD8+T cells of tumor microenvironment, indicating the sensitivity of B-cell lymphoma to PD-L1 blockade. Also CD8+T cells could be a therapeutic mediator of immune checkpoint inhibitors in treating EBV-associated lymphoid malignancies.
Full text
Available for:
DOBA, IZUM, KILJ, NUK, PILJ, PNG, SAZU, SIK, UILJ, UKNU, UL, UM, UPUK
Polymer‐based dielectrics are attracting increasing attention due to their high‐density energy storage. However, mitigating the heat generation in real capacitors has been a challenge. Here an ...electrothermal breakdown phase‐field model is developed to fundamentally understand the thermal effects on the dielectric breakdown of polymer‐based dielectrics in real capacitor configurations including the increase in the dielectric loss and the decrease in the breakdown strength. While both enhancing the thermal conductivity and reducing the electrical conductivity of the polymer nanocomposites can reduce the thermal effects, it is found that reducing the electrical conductivity is more effective. This work is expected to not only stimulate attention to the thermal effects in polymer‐based dielectrics but also provide a fundamental guidance to mitigate the heat‐induced deterioration of breakdown strength.
An electrothermal breakdown phase‐field model is developed to fundamentally understand the thermal effects on the breakdown behavior of polymer‐based dielectrics with different microstructures. The predicted temperature‐dependent breakdown strengths agree with the available experimental measurements. It is found that reducing the electrical conductivity is more effective than enhancing the thermal conductivity of the polymer nanocomposite to reduce the thermal effects.
Full text
Available for:
FZAB, GIS, IJS, KILJ, NLZOH, NUK, OILJ, SAZU, SBCE, SBMB, UL, UM, UPUK