VSE knjižnice (vzajemna bibliografsko-kataložna baza podatkov COBIB.SI)
-
Investigation of mechanical properties of horn powder-filled epoxy compositesKumar, Duraisamy ...Recent environmental concerns focus on the development of bio-composites, due to their low cost, and eco-friendly and bio-degradability characteristics. The aim of this work is to investigate the ... properties of particle-filled composites fabricated using bio-waste horn powder (HP) and epoxy resin. Composites were fabricated according to a Taguchi L 9 (3x3) orthogonal array. The HP particles and matrix were mixed in an appropriate ratio, compression-moulded and cured at room temperature to produce the specimens. Properties, such as ultimate tensile strength, tensile modulus, elongation percentage at break, flexural strength, flexural modulus, impact strength and microstructure of the specimens, were investigated. Scanning electron microscopy (SEM) micrographs of tensile tested specimens show good compatibility between HP particles and resin, when the HP volume is at 10 % and increases in agglomeration with increase in the HP volume percentage. Optimization of factors was done using grey relational analysis (GRA) and analysis of variance (ANOVA). The optimum factor levels were found to be the highest NaOH concentration (con.), A 3 (i.e., 0.3 N), the smallest HP size, B 1 (i.e., 125 [micro]m) and the lowest HP volume percentage, C 1 (i.e., 10 %). The contribution of influencing factors in decreasing order were found to be, HP volume percentage with 90.87 %, HP size with 6.43 % and NaOH concentration with 0.78 %. From the R squared and R squared adjusted values of the properties, it is determined that most of the values are above 95 %, confirming a 95 % confidence level. Comparison between the optimum specimen and untreated HP specimens reveals that the optimum specimen has better properties. Hence, HP/epoxy composites can find application in various sectorsVir: Strojniški vestnik = Journal of mechanical engineering. - ISSN 0039-2480 (Vol. 63, no. 2, Feb. 2017, str. 138-147, SI 19)Vrsta gradiva - članek, sestavni delLeto - 2017Jezik - angleškiCOBISS.SI-ID - 15303707
vir: Strojniški vestnik = Journal of mechanical engineering. - ISSN 0039-2480 (Vol. 63, no. 2, Feb. 2017, str. 138-147, SI 19)
Vnos na polico
Trajna povezava
- URL:
Faktor vpliva
Dostop do baze podatkov JCR je dovoljen samo uporabnikom iz Slovenije. Vaš trenutni IP-naslov ni na seznamu dovoljenih za dostop, zato je potrebna avtentikacija z ustreznim računom AAI.
Leto | Faktor vpliva | Izdaja | Kategorija | Razvrstitev | ||||
---|---|---|---|---|---|---|---|---|
JCR | SNIP | JCR | SNIP | JCR | SNIP | JCR | SNIP |
Baze podatkov, v katerih je revija indeksirana
Ime baze podatkov | Področje | Leto |
---|
Povezave do osebnih bibliografij avtorjev | Povezave do podatkov o raziskovalcih v sistemu SICRIS |
---|---|
Kumar, Duraisamy | |
Rajendra Boopathy, Sadayan | |
Sangeetha, Dharmalingam | |
Bharathiraja, Govindarajan |
Vir: Osebne bibliografije
in: SICRIS
Izberite prevzemno mesto:
Prevzem gradiva po pošti
Naslov za dostavo:
Med podatki člana manjka naslov.
Storitev za pridobivanje naslova trenutno ni dostopna, prosimo, poskusite še enkrat.
S klikom na gumb "V redu" boste potrdili zgoraj izbrano prevzemno mesto in dokončali postopek rezervacije.
S klikom na gumb "V redu" boste potrdili zgoraj izbrano prevzemno mesto in naslov za dostavo ter dokončali postopek rezervacije.
S klikom na gumb "V redu" boste potrdili zgoraj izbrani naslov za dostavo in dokončali postopek rezervacije.
Obvestilo
Trenutno je storitev za avtomatsko prijavo in rezervacijo nedostopna. Gradivo lahko rezervirate sami na portalu Biblos ali ponovno poskusite tukaj kasneje.
Gesla v Splošnem geslovniku COBISS
Izbira mesta prevzema
Gradivo iz matične enote je brezplačno. Če je gradivo na mesto prevzema dostavljeno iz drugih enot, lahko knjižnica to storitev zaračuna.
Mesto prevzema | Status gradiva | Rezervacija |
---|
Rezervacija v teku
Prosimo, počakajte trenutek.
Rezervacija je uspela.
Rezervacija ni uspela.
Rezervacija...
Članska izkaznica:
Mesto prevzema: