VSE knjižnice (vzajemna bibliografsko-kataložna baza podatkov COBIB.SI)
-
Effect of laser shock peening on fretting wear behaviour of AISI 304 stainless alloy [Elektronski vir]Li, Chao, strojništvo ...Unlike many other surface treatment techniques, such as shot peening (SP), low plasticity burnishing (LPB), ultrasonic surface rolling process (USRP), ultrasonic nanocrystal surface modification ... (UNSM), laser shock peening (LSP) is a non-contact process. This means that LSP achieves surface modification without direct physical contact, thereby eliminating the risk of media contamination and undesired wear on the peening equipment. As a surface hardening technology, LSP tends to produce a hardened layer with a high gradient of residual stress (RS) in the near-surface, significantly enhancing wear resistance. The well-known wear theories applied for numerical prediction, whether Archard model or dissipated frictional-energy model, contain a multiplier for contact pressure and relative slip amplitude or shear stress and relative slip amplitude , respectively. These multipliers are sensitive to the mechanical properties near the surface. Additionally, the wear profile is governed not only by the wear effect but also by the deformation of materials. Therefore, to accurately evaluate the wear performance for surface-hardened materials, the influence of RS is hard to be overlooked. In this work, the finite element method (FEM) is utilised to construct a 3D numerical model, which ignores and considers RS, for both as-received and LSP-treated samples. Two distinct RS distributions induced by different scanning strategies (one- and five-time), are introduced in the finite element (FE) model. The numerical simulation results are then compared with the experimental data to verify the accuracy of the fretting wear model built in this study. On this basis, the impact of different RS distributions on fretting wear characteristics, including wear profile and volume, is extensively investigated. The findings reveal that higher amplitude RS can reduce the degree of fretting wear to a greater extent, highlighting the beneficial role of RS in enhancing wear resistance. Furthermore, the numerical models incorporating RS demonstrate superior predictive accuracy compared to those that omit RS. This naturally underscores the importance of integrating RS in numerical simulations of LSP and other surface-hardened materials. Previous article in issueNext article in issue Keywords Laser shock peeningResidual stressFretting wearFinite element method 1. Introduction Fretting wear, a specific wear type, arises at the interfaces of two components subjected to small-amplitude oscillatory motion or vibration [1]. The fretting wear mechanism is characterized by high local stresses, microslip motion, and repetitive contact cycles, leading to concentrated wear and surface damage, rendering components vulnerable to material loss and reduced lifespan [2]. Notably, fretting wear can act as a precursor to fatigue and fracture failures [3], [4], [5]. The cyclic nature of fretting motion, combined with the presence of local stress concentrations, can initiate and propagate fatigue cracks, potentially resulting in catastrophic failures under applied loads.Vir: Tribology international [Elektronski vir]. - ISSN 1879-2464 (Vol. 193, article no. 109386, May 2024, str. 1-17)Vrsta gradiva - e-članek ; neleposlovje za odrasleLeto - 2024Jezik - angleškiCOBISS.SI-ID - 197751043
Avtor
Li, Chao, strojništvo |
Amanov, Auezhan |
Wang, Can, fizik |
Wang, Lihua |
Abdel Wahab, Magd
Teme
laser |
napetost |
priskušanje materialov |
laser shock peening |
fretting wear |
materials
![loading ... loading ...](themes/default/img/ajax-loading.gif)
Vnos na polico
Trajna povezava
- URL:
Faktor vpliva
Dostop do baze podatkov JCR je dovoljen samo uporabnikom iz Slovenije. Vaš trenutni IP-naslov ni na seznamu dovoljenih za dostop, zato je potrebna avtentikacija z ustreznim računom AAI.
Leto | Faktor vpliva | Izdaja | Kategorija | Razvrstitev | ||||
---|---|---|---|---|---|---|---|---|
JCR | SNIP | JCR | SNIP | JCR | SNIP | JCR | SNIP |
Baze podatkov, v katerih je revija indeksirana
Ime baze podatkov | Področje | Leto |
---|
Povezave do osebnih bibliografij avtorjev | Povezave do podatkov o raziskovalcih v sistemu SICRIS |
---|---|
Li, Chao, strojništvo | ![]() |
Amanov, Auezhan | ![]() |
Wang, Can, fizik | ![]() |
Wang, Lihua | ![]() |
Abdel Wahab, Magd | 59211 |
Vir: Osebne bibliografije
in: SICRIS
Izberite prevzemno mesto:
Prevzem gradiva po pošti
Naslov za dostavo:
Med podatki člana manjka naslov.
Storitev za pridobivanje naslova trenutno ni dostopna, prosimo, poskusite še enkrat.
S klikom na gumb "V redu" boste potrdili zgoraj izbrano prevzemno mesto in dokončali postopek rezervacije.
S klikom na gumb "V redu" boste potrdili zgoraj izbrano prevzemno mesto in naslov za dostavo ter dokončali postopek rezervacije.
S klikom na gumb "V redu" boste potrdili zgoraj izbrani naslov za dostavo in dokončali postopek rezervacije.
Obvestilo
Trenutno je storitev za avtomatsko prijavo in rezervacijo nedostopna. Gradivo lahko rezervirate sami na portalu Biblos ali ponovno poskusite tukaj kasneje.
Gesla v Splošnem geslovniku COBISS
Izbira mesta prevzema
Gradivo iz matične enote je brezplačno. Če je gradivo na mesto prevzema dostavljeno iz drugih enot, lahko knjižnica to storitev zaračuna.
Mesto prevzema | Status gradiva | Rezervacija |
---|
Rezervacija v teku
Prosimo, počakajte trenutek.
Rezervacija je uspela.
Rezervacija ni uspela.
Rezervacija...
Članska izkaznica:
Mesto prevzema: