VSE knjižnice (vzajemna bibliografsko-kataložna baza podatkov COBIB.SI)
-
Microstructure and residual stress analysis after steel and laser alloyingGrum, Janez, 1946- ; Žnidaršič, Matjaž, 1964-The paper treats laser alloying by remelting of the parent metal and the filler material. With the selection of the filler material in powder form, the influence of silicon carbide in powder form on ... the efficiency of melting and alloying was studied too. The SiC powder is a readily available material known for numerous applications due to its high hardness and corrosion resistance. In laser alloying experiments, low-carbon steel was used. When the SiC powder is added in laser remelting, it completely disintegrates into Si and C which then dissolve in the molten pool. The remelted layer of the parent metal will pick up carbon whereas silicon will make a solution. Self-through-hardening of the thin remelted and alloyed surface layer considerably increases the microhardness of the surface layer, i.e., to more than 800 HV_0,1. The increased hardness results in a considerable increase in wear resistance of the material. During the melting process of the two materials, fast and efficient alloying, i.e., remelting by dissolving C and Si, can be ensured; therefore, the surface practically need not to be machined after the process. Because of the high hardness and good surface quality only fine grinding may be used if needed. As regards residual stresses, they are favourable since in the thin surface layer even compression residual stresses occur, which then slowly and uniformly transform into tensile residual stresses.Vir: Computer integrated manufacturing and high speed machining : knjiga sažetaka (Str. IV-089)Vrsta gradiva - prispevek na konferenciLeto - 2002Jezik - angleškiCOBISS.SI-ID - 5253403
![loading ... loading ...](themes/default/img/ajax-loading.gif)
Vnos na polico
Trajna povezava
- URL:
Faktor vpliva
Dostop do baze podatkov JCR je dovoljen samo uporabnikom iz Slovenije. Vaš trenutni IP-naslov ni na seznamu dovoljenih za dostop, zato je potrebna avtentikacija z ustreznim računom AAI.
Leto | Faktor vpliva | Izdaja | Kategorija | Razvrstitev | ||||
---|---|---|---|---|---|---|---|---|
JCR | SNIP | JCR | SNIP | JCR | SNIP | JCR | SNIP |
Baze podatkov, v katerih je revija indeksirana
Ime baze podatkov | Področje | Leto |
---|
Povezave do osebnih bibliografij avtorjev | Povezave do podatkov o raziskovalcih v sistemu SICRIS |
---|---|
Grum, Janez, 1946- | 03551 |
Žnidaršič, Matjaž, 1964- | 10897 |
Vir: Osebne bibliografije
in: SICRIS
Izberite prevzemno mesto:
Prevzem gradiva po pošti
Naslov za dostavo:
Med podatki člana manjka naslov.
Storitev za pridobivanje naslova trenutno ni dostopna, prosimo, poskusite še enkrat.
S klikom na gumb "V redu" boste potrdili zgoraj izbrano prevzemno mesto in dokončali postopek rezervacije.
S klikom na gumb "V redu" boste potrdili zgoraj izbrano prevzemno mesto in naslov za dostavo ter dokončali postopek rezervacije.
S klikom na gumb "V redu" boste potrdili zgoraj izbrani naslov za dostavo in dokončali postopek rezervacije.
Obvestilo
Trenutno je storitev za avtomatsko prijavo in rezervacijo nedostopna. Gradivo lahko rezervirate sami na portalu Biblos ali ponovno poskusite tukaj kasneje.
Gesla v Splošnem geslovniku COBISS
Izbira mesta prevzema
Gradivo iz matične enote je brezplačno. Če je gradivo na mesto prevzema dostavljeno iz drugih enot, lahko knjižnica to storitev zaračuna.
Mesto prevzema | Status gradiva | Rezervacija |
---|
Rezervacija v teku
Prosimo, počakajte trenutek.
Rezervacija je uspela.
Rezervacija ni uspela.
Rezervacija...
Članska izkaznica:
Mesto prevzema: