Nowadays, the most commonly used fixation systems are non-resorbable, but new resorbable magnesium alloy fixation screws have been introduced recently. Therefore, the aim of this study was to compare ...the magnesium fixation screw and the commonly used non-resorbable titanium screw in an animal model. Four 3-wall defect sites were covered with collagen membranes in the mandible of twenty beagle dogs (two sites on the left and two on the right). Each membrane was fixed with either four magnesium screws or four titanium screws. Post-operative follow-up revealed the expected observations such as transient inflammation and pain. Both groups showed a good healing response, with no differences between groups. Micro-CT analysis showed no significant difference between groups in terms of BV/TV or soft tissue volume. The void volume in the magnesium fixation screw group continued to decrease on average between the different timepoints, but not significantly. Furthermore, a gradual progression of the degradation process of the magnesium screws was observed in the same group. Magnesium screws and titanium screws showed equal performance in tissue regeneration according to GBR principles. An additional advantage of magnesium screws is their resorbable nature, which eliminates the need for a second surgical step to remove the screws.
Introduction: Titanium-based implants can be used to fill voids in bone reconstruction surgery. Through additive manufacturing (AM), it is possible to produce titanium implants with osteoconductive ...properties such as high porosity and low stiffness. AM facilitates a level of design flexibility and personalization that is not feasible with traditional techniques. Methods: In this study, osseointegration into titanium alloy (Ti-6Al-4V) lattices was investigated for 12 weeks post-implantation using a novel bicortical load-bearing ovine model. The objective was to assess the safety and efficacy of AM-fabricated implants using two lattice structures of contrasting stiffness spanning the full width of the femoral condyle. Results: This was achieved by evaluating implant osseointegration and bone–implant contact properties by histomorphometry, scoring local implant tissue responses via histopathology, and micro-computed tomography reconstruction. Discussion: We found that Ti-6Al-4V implants facilitated widespread and extensive osseointegration, with bone maturation ongoing at the conclusion of the trial period. Following the implantation period, no adverse clinical indications that could be directly ascribed to the presence of the implanted device were identified, as determined by macroscopic and microscopic observation.
Chronic osteomyelitis in presence of orthopedic implants is a condition observed in the field of biomaterials as it impairs early bone-implant contact, fixation and integration. In this study, a ...surgical intramedullary tibial insertion was performed using a titanium wire previously inoculated with
Staphylococcus aureus
in order to develop an osteomyelitis model in a clinically relevant long bone and in absence of any prophylactic treatment. As such, twenty-two male Sprague-Dawley rats received a sterile or inoculated intramedullary biomaterial with either 2 × 10
6
or 1 × 10
7
S. aureus
colony forming units. Bacterial burden, inflammation, morphological changes, as well as newly formed bone tissues were evaluated for histopathology following a period of either eight or fifteen days of implantation. The implant inoculated in presence of the highest bacterial load was effective to produce significant periprosthetic infection observations in addition to hard and soft tissue inflammation consistent with the development of osteomyelitis. In contrast, neither the sterile nor the low-dose implant inoculation showed inflammation and clinical infection signs, but rather produced an expected bone remodeling and appropriate healing associated with biomaterial implantation. Complete health assessment is presented with histopathological periprosthetic results.
Disks consisting of macroporous nickel–titanium alloy (NiTi, Nitinol
®, Actipore
®) are used as implants in clinical surgery, e.g. for fixation of spinal dysfunctions. The morphological properties ...were studied by scanning electron microscopy (SEM) and by synchrotron radiation-based microtomography (SRμCT). The composition was studied by X-ray diffractometry (XRD), differential scanning calorimetry (DSC), and energy-dispersive X-ray spectroscopy (EDX). The mechanical properties were studied with temperature-dependent dynamical mechanical analysis (DMA). Studies on the biocompatibility were performed by co-incubation of porous NiTi samples with isolated peripheral blood leukocyte fractions (polymorphonuclear neutrophil granulocytes, PMN; peripheral blood mononuclear leukocytes, PBMC) in comparison with control cultures without NiTi samples. The cell adherence to the NiTi surface was analyzed by fluorescence microscopy and scanning electron microscopy. The activation of adherent leukocytes was analyzed by measurement of the released cytokines using enzyme-linked immunosorbent assay (ELISA). The cytokine response of PMN (analyzed by the release of IL-1ra and IL-8) was not significantly different between cell cultures with or without NiTi. There was a significant increase in the release of IL-1ra (
p
<
0.001
), IL-6 (
p
<
0.05
), and IL-8 (
p
<
0.05
) from PBMC in the presence of NiTi samples. In contrast, the release of TNF-
α by PBMC was not significantly elevated in the presence of NiTi. IL-2 was released from PBMC only in the range of the lower detection limit in all cell cultures. The material, clearly macroporous with an interconnecting porosity, consists of NiTi (martensite; monoclinic, and austenite; cubic) with small impurities of NiTi
2 and possibly NiC
x
. The material is not superelastic upon manual compression and shows a good biocompatibility.
Orthopedic medical devices are continuously evolving for the latest clinical indications in craniomaxillofacial, spine, trauma, joint arthroplasty, sports medicine, and soft tissue regeneration ...fields, with a variety of materials from new metallic alloys and ceramics to composite polymers, bioresorbables, or surface-treated implants. There is great need for qualified medical device pathologists to evaluate these next generation biomaterials, with improved biocompatibility and bioactivity for orthopedic applications, and a broad range of knowledge is required to stay abreast of this ever-changing field. Orthopedic implants require specialized imaging and processing techniques to fully evaluate the bone-implant interface, and the pathologist plays an important role in determining the proper combination of histologic processing and staining for quality slide production based on research and development trials and validation. Additionally, histomorphometry is an essential part of the analysis to quantify tissue integration and residual biomaterials. In this article, an overview of orthopedic implants and animal models, as well as pertinent insights for tissue collection, imaging, processing, and slide generation will be provided with a special focus on histopathology and histomorphometry evaluation.
This study compared the degradation profile, safety, and efficacy of bioresorbable magnesium alloy and polylactide–co-glycolide (PLGA) polymer osteosynthesis systems for the treatment of fractures in ...a load-sharing maxillofacial environment using a new mini-swine fracture fixation model.
Two types of clinically relevant situations were evaluated in 5 Yucatan miniature pigs. Defined porcine midface osteotomies of the supraorbital rim and zygoma were created and fixed with either a coated magnesium (test animals) or PLGA plate and screw osteosynthesis system (control animals). After surgery, the mini-pigs were able to recover for either 1 or 9 months with continuous in vivo post-implantation monitoring. Standardized computed tomography (CT) imaging was taken immediately postoperatively and at termination for all animals. The 9-month cohort also underwent CT at 2, 4, and 6 months after surgery. At necropsy, osteotomy sites and bone-implant units were harvested, and healing was evaluated by micro-CT, histopathology, and histomorphometry.
After clinical and radiologic follow-up examination, all fracture sites healed well for both the magnesium and polymer groups regardless of time point. Complete bone union and gradually disappearing osteotomy lines were observed across all implantation sites, with no major consistency change in periprosthetic soft tissue or in soft tissue calcification. Macroscopic and microscopic examination showed no negative influence of gas formation observed with magnesium during the healing process. Histopathologic analysis showed similar fracture healing outcomes for both plating systems with good biocompatibility as evidenced by a minimal or mild tissue reaction.
This study confirms that WE43 magnesium alloy exhibited excellent fracture healing properties before its full degradation without causing any substantial inflammatory reactions in a long-term porcine model. Compared with PLGA implants, magnesium represents a promising new biomaterial with reduced implant sizes and improved mechanical properties to support fracture healing in a load-sharing environment.
PDF
