Interferometric gravitational-wave detectors like LIGO need to be able to measure changes in their arm lengths of order 10−18 m or smaller. This requires very high laser power in order to raise the ...signal above shot noise. One significant limitation to increased laser power is an optomechanical interaction between the laser field and the detector's test masses that can form an unstable feedback loop. Such parametric instabilities have long been studied as a limiting effect at high power, and were first observed to occur in LIGO in 2014. Since then, passive and active means have been used to avoid these instabilities, though at power levels well below the final design value. Here we report on the successful implementation of tuned, passive dampers to tame parametric instabilities in LIGO. These dampers are applied directly to all interferometer test masses to reduce the quality factors of their internal vibrational modes, while adding a negligible amount of noise to the gravitational-wave output. In accordance with our model, the measured mode quality factors have been reduced by at least a factor of 10 with no visible increase in the interferometer's thermal noise level. We project that these dampers should remove most of the parametric instabilities in LIGO when operating at full power, while limiting the concomitant increase in thermal noise to approximately 1%.
Advanced gravitational-wave detectors such as the laser interferometer gravitational-wave observatories (LIGO) require an unprecedented level of isolation from the ground. When in operation, they ...measure motion of less than 10−19 m. Strong teleseismic events like earthquakes disrupt the proper functioning of the detectors, and result in a loss of data. An earthquake early-warning system, as well as a prediction model, have been developed to understand the impact of earthquakes on LIGO. This paper describes a control strategy to use this early-warning system to reduce the LIGO downtime by 30%. It also presents a plan to implement this new earthquake configuration in the LIGO automation system.
The two-stage vibration isolation and positioning platform provides passive and active isolation in all directions and translation. It uses a unique combination of position sensors, geophones and ...broadband seismometers to provide unprecedented levels of isolation.
•The paper presents the two-stage vibration isolation and positioning platform used in Advanced LIGO gravitational waves detectors.•The system can support a 1000kg of sensitive equipment and operate in ultra-high vacuum.•Each of the two stages provide passive and active isolation in all directions of translation and rotation (12 axis).•The active control strategy uses a unique combination of relative sensors, geophones and broadband seismometers.•The system reduces the motion to the level of 10−11 m/Hz at 1Hz and 10−12 m/Hz at 10Hz.
New generations of gravity wave detectors require unprecedented levels of vibration isolation. This paper presents the final design of the vibration isolation and positioning platform used in Advanced LIGO to support the interferometer's core optics. This five-ton two-and-half-m wide system operating in ultra-high vacuum. It features two stages of isolation mounted in series. The stages are imbricated to reduce the overall height. Each stage provides isolation in all directions of translation and rotation. The system is instrumented with a unique combination of low noise relative and inertial sensors. The active control provides isolation from 0.1Hz to 30Hz. It brings the platform motion down to 10−11 m/Hz at 1Hz. Active and passive isolation combine to bring the platform motion below 10−12 m/Hz at 10Hz. The passive isolation lowers the motion below 10−13 m/Hz at 100Hz. The paper describes how the platform has been engineered not only to meet the isolation requirements, but also to permit the construction, testing, and commissioning process of the fifteen units needed for Advanced LIGO observatories.
The two-stage vibration isolation and positioning platform (BSC-ISI) provides three orders of magnitude of isolation at all frequencies above 1Hz.
•The paper presents near a decade of research on the ...two-stage twelve-axis vibration isolation platforms developed for Advanced LIGO.•This system positions and isolates 1000kg of very sensitive equipment in all directions of translation and rotation.•The system provides more than three orders of magnitude of isolation over a very large bandwidth.•We show how results from the prototyping phases have been used for the production and commissioning of 15 units.•Isolation results show that the system brings the motion below 10−11m/Hz at 1Hz and 10−12 m/Hz at 10Hz.
This paper presents the results of the past seven years of experimental investigation and testing done on the two-stage twelve-axis vibration isolation platform for Advanced LIGO gravity waves observatories. This five-ton two-and-half-meter wide system supports more than a 1000kg of very sensitive equipment. It provides positioning capability and seismic isolation in all directions of translation and rotation. To meet the very stringent requirements of Advanced LIGO, the system must provide more than three orders of magnitude of isolation over a very large bandwidth. It must bring the motion below 10−11 m/Hz at 1Hz and 10−12 m/Hz at 10Hz. A prototype of this system has been built in 2006. It has been extensively tested and analyzed during the following two years. This paper shows how the experimental results obtained with the prototype were used to engineer the final design. It highlights how the engineering solutions implemented not only improved the isolation performance but also greatly simplified the assembly, testing, and commissioning process. During the past two years, five units have been constructed, tested, installed and commissioned at each of the two LIGO observatories. Five other units are being built for an upcoming third observatory. The test results presented show that the system meets the motion requirements, and reach the sensor noise in the control bandwidth.
We present a new approach for characterizing the loss factor of materials, using a suspended mechanical oscillator. Compared to more standard techniques, this method offers freedom in terms of the ...size and shape of the tested samples. Using a finite element model and the vibration measurements, the loss factor is deduced from the oscillator's ring-down. In this way the loss factor can be estimated independently for shear and compression deformation of the sample over a range of frequencies. As a proof of concept, we present measurements for EPO-TEK 353ND epoxy samples.
The Laser Interferometer Gravitational Wave Observatory (LIGO) has been directly detecting gravitational waves from compact binary mergers since 2015. We report on the first use of squeezed vacuum ...states in the direct measurement of gravitational waves with the Advanced LIGO H1 and L1 detectors. This achievement is the culmination of decades of research to implement squeezed states in gravitational-wave detectors. During the ongoing O3 observation run, squeezed states are improving the sensitivity of the LIGO interferometers to signals above 50 Hz by up to 3 dB, thereby increasing the expected detection rate by 40% (H1) and 50% (L1).
The measurement of minuscule forces and displacements with ever greater precision is inhibited by the Heisenberg uncertainty principle, which imposes a limit to the precision with which the position ...of an object can be measured continuously, known as the standard quantum limit
. When light is used as the probe, the standard quantum limit arises from the balance between the uncertainties of the photon radiation pressure applied to the object and of the photon number in the photoelectric detection. The only way to surpass the standard quantum limit is by introducing correlations between the position/momentum uncertainty of the object and the photon number/phase uncertainty of the light that it reflects
. Here we confirm experimentally the theoretical prediction
that this type of quantum correlation is naturally produced in the Laser Interferometer Gravitational-wave Observatory (LIGO). We characterize and compare noise spectra taken without squeezing and with squeezed vacuum states injected at varying quadrature angles. After subtracting classical noise, our measurements show that the quantum mechanical uncertainties in the phases of the 200-kilowatt laser beams and in the positions of the 40-kilogram mirrors of the Advanced LIGO detectors yield a joint quantum uncertainty that is a factor of 1.4 (3 decibels) below the standard quantum limit. We anticipate that the use of quantum correlations will improve not only the observation of gravitational waves, but also more broadly future quantum noise-limited measurements.
Really cool mirrors
Cooling objects to low temperature can increase the sensitivity of sensors and the operational performance of most devices. Removing most of the thermal vibrations—or phonons—such ...that the object reaches its motional quantum ground state has been achieved but typically with tiny, nanoscale objects. Using the suspended mirrors of the Laser Interferometer Gravitational-Wave Observatory (LIGO) that form a 10-kg optomechanical oscillator, Whittle
et al.
demonstrate the ability to cool such a large-scale object to nearly the motional ground state. An upgrade to LIGO with such a modification could increase its sensitivity and range to gravitational waves but also extend studies of quantum mechanics to large-scale objects.
Science
, abh2634, this issue p.
1333
A 10-kg mechanical oscillator, the mirror of LIGO, is cooled to near its motional quantum ground state.
The motion of a mechanical object, even a human-sized object, should be governed by the rules of quantum mechanics. Coaxing them into a quantum state is, however, difficult because the thermal environment masks any quantum signature of the object’s motion. The thermal environment also masks the effects of proposed modifications of quantum mechanics at large mass scales. We prepared the center-of-mass motion of a 10-kilogram mechanical oscillator in a state with an average phonon occupation of 10.8. The reduction in temperature, from room temperature to 77 nanokelvin, is commensurate with an 11 orders-of-magnitude suppression of quantum back-action by feedback and a 13 orders-of-magnitude increase in the mass of an object prepared close to its motional ground state. Our approach will enable the possibility of probing gravity on massive quantum systems.
Noise due to scattered light has been a frequent disturbance in the advanced LIGO gravitational wave detectors, hindering the detection of gravitational waves. The non stationary scatter noise caused ...by low frequency motion can be recognized as arches in the time-frequency plane of the gravitational wave channel. In this paper, we characterize the scattering noise for LIGO and Virgo's third observing run O3 from April, 2019 to March, 2020. We find at least two different populations of scattering noise and we investigate the multiple origins of one of them as well as its mitigation. We find that relative motion between two specific surfaces is strongly correlated with the presence of scattered light and we implement a technique to reduce this motion. We also present an algorithm using a witness channel to identify the times this noise can be present in the detector.
PDF
