ZnO crystallites were grown by electroless deposition on poly(methyl methacrylate) (PMMA) fiber mats prepared by an electrospinning technique. The electroless deposition involves three steps: ...sensitization, activation and deposition, which were performed by subsequently dipping the PMMA fiber mats in the appropriate solutions. After the deposition the PMMA fibers are uniformly coated with ZnO prisms which show hexagonal wurtzite structure and optical signatures (band-gap value and emission bands) typical for this semiconductor. By combining electroless deposition and electrospinning, different semiconductor coated polymer fibers can be obtained for a wide range of applications. Both methods are appropriate for large scale production, being scalable, cheap, efficient and suitable for large-area covering techniques.
•ZnO-coated PMMA fibers were prepared by combining two low cost and scalable techniques: electrospinning and electroless deposition.•PMMA fibers were uniformly coated with ZnO prisms shaped crystallites.•ZnO prisms show a hexagonal wurtzite structure and optical signatures typical for this semiconductor (band-gap value and emission bands).
A non-conventional, bioinspired device based on polypyrrole coated electrospun fibrous microstructures, which simultaneously works as artificial muscle and mechanical sensor is reported. Fibrous ...morphology is preferred due to its high active surface which can improve the actuation/sensing properties, its preparation still being challenging. Thus, a simple fabrication algorithm based on electrospinning, sputtering deposition and electrochemical polymerization produced electroactive aligned ribbon meshes with analogous characteristics as natural muscle fibers. These can simultaneously generate a movement (by applying an electric current/potential) and sense the effort of holding weights (by measuring the potential/current while holding objects up to 21.1 mg). Electroactivity was consisting in a fast bending/curling motion, depending on the fiber strip width. The amplitude of the movement decreases by increasing the load, a behavior similar with natural muscles. Moreover, when different weights were hung on the device, it senses the load modification, demonstrating a sensitivity of about 7 mV/mg for oxidation and - 4 mV/mg for reduction. These results are important since simultaneous actuation and sensitivity are essential for complex activity. Such devices with multiple functionalities can open new possibilities of applications as e.g. smart prosthesis or lifelike robots.
The work describes the development of a flexible, hydrogel embedded pH-sensor that can be integrated in inexpensive wearable and non-invasive devices at epidermal level for electrochemical ...quantification of H
ions in sweat. Such a device can be useful for swift, real time diagnosis and for monitoring specific conditions. The sensors' working electrodes are flexible poly(methyl methacrylate) electrospun fibers coated with a thin gold layer and electrochemically functionalized with nanostructured palladium/palladium oxide. The response to H
ions is investigated by cyclic voltammetry and electrochemical impedance spectroscopy while open circuit potential measurements show a sensitivity of aprox. -59 mV per pH unit. The modification of the sensing interface upon basic and acid treatment is characterized by scanning and transmission electron microscopy and the chemical composition by X-ray photoelectron spectroscopy. In order to demonstrate the functionality of the pH-sensor at epidermal level, as a wearable device, the palladium/palladium oxide working electrode and silver/silver chloride reference electrode are embedded within a pad of polyacrylamide hydrogel and measurements in artificial sweat over a broad pH range were performed. Sensitivity up to -28 mV/pH unit, response time below 30 s, temperature dependence of approx. 1 mV/°C as well as the minimum volume to which the sensor responses of 250 nanoliters were obtained for this device. The proposed configuration represents a viable alternative making use of low-cost and fast fabrication processes and materials.
Abstract
The present work reports a new configuration of soft artificial muscle based on a web of metal covered nylon 6/6 micrometric fibers attached to a thin polydimethylsiloxane (PDMS) film. The ...preparation process is simple and implies the attachment of metalized fiber networks to a PDMS sheet substrate while heating and applying compression. The resulting composite is versatile and can be cut in different shapes as a function of the application sought. When an electric current passes through the metallic web, heat is produced, leading to local dilatation and to subsequent controlled deformation. Because of this, the artificial muscle displays a fast and ample movement (maximum displacement of 0.8 cm) when applying a relatively low voltage (2.2 V), a consequence of the contrast between the thermal expanse coefficients of the PDMS substrate and of the web-like electrode. It was shown that the electrical current producing this effect can originate from both direct electric contacts, and untethered configurations i.e. radio frequency induced. Usually, for thermal activated actuators the heating is produced by using metallic films or conductive carbon-based materials, while here a fast heating/cooling process is obtained by using microfiber-based heaters. This new approach for untethered devices is an interesting path to follow, opening a wide range of applications were autonomous actuation and remote transfer of energy are needed.
The current study reports on the fabrication of composite scaffolds based on polycaprolactone (PCL) and cerium (Ce)-containing powders, followed by their characterization from compositional, ...structural, morphological, optical and biological points of view. First, CeO2, Ce-doped calcium phosphates and Ce-substituted bioglass were synthesized by wet-chemistry methods (precipitation/coprecipitation and sol-gel) and subsequently loaded on PCL fibres processed by electrospinning. The powders were proven to be nanometric or micrometric, while the investigation of their phase composition showed that Ce was present as a dopant within the crystal lattice of the obtained calcium phosphates or as crystalline domains inside the glassy matrix. The best bioactivity was attained in the case of Ce-containing bioglass, while the most pronounced antibacterial effect was visible for Ce-doped calcium phosphates calcined at a lower temperature. The scaffolds were composed of either dimensionally homogeneous fibres or mixtures of fibres with a wide size distribution and beads of different shapes. In most cases, the increase in polymer concentration in the precursor solution ensured the achievement of more ordered fibre mats. The immersion in SBF for 28 days triggered an incipient degradation of PCL, evidenced mostly through cracks and gaps. In terms of biological properties, the composite scaffolds displayed a very good biocompatibility when tested with human osteoblast cells, with a superior response for the samples consisting of the polymer and Ce-doped calcium phosphates.
Display omitted
•Gold covered electrospun polycaprolactone fibers (Au/PCL) as self-standing device.•O2 detection via electrochemical methods using the Au/PCL sensors.•Electrochemical O2 ...quantification in cellular media in two electrode configuration.
This work reports the use of electrospun conductive gold covered polycaprolactone fibers for the quantification of dissolved O2. The morphologies of the electrospun fibers obtained at a static and a dynamic drum collector were investigated by scanning electron microscopy. The reduction process of O2 at negative potentials is analyzed by cyclic voltammetry and electrochemical impedance spectroscopy (EIS) in sodium phosphate buffer (NaPB) pH 7.0 and in cellular media pH 7.4. The electrochemical sensing performance of Au/PCL towards O2 quantification in NaPB and cellular media is compared by using three electrochemical techniques: cyclic and linear sweep voltammetry and EIS. Measurements are done in a two electrode configuration, using a silver wire as reference, to show the applicability of the method for O2 quantification in cellular culture media.
Web-like architectures of ZnO and TiO2 nanotubes were fabricated based on a three-step process of templating polymer nanofibers produced by electrospinning (step 1). The electrospun polymer ...nanofibers were covered by radio-frequency magnetron sputtering with thin layers of semiconducting materials (step 2), with FESEM observations proving uniform deposits over their entire surface. ZnO or TiO2 nanotubes were obtained by subsequent calcination (step 3). XRD measurements proved that the nanotubes were of a single crystalline phase (wurtzite for ZnO and anatase for TiO2) and that no other crystalline phases appeared. No other elements were present in the composition of the nanotubes, confirmed by EDX measurements. Reflectance spectra and Tauc plots of Kubelka–Munk functions revealed that the band gaps of the nanotubes were lower than those of the bulk materials (3.05 eV for ZnO and 3.16 eV for TiO2). Photocatalytic performances for the degradation of Rhodamine B showed a large degradation efficiency, even for small quantities of nanotubes (0.5 mg/10 mL dye solution): ~55% for ZnO, and ~95% for TiO2.
•Fabrication of a new actuator configuration based on polyaniline/gold microtubes.•The actuator bends by switching the potential between −0.2 and 1V, even when simulated gastric fluid was used as ...electrolyte.•The charge transfer resistance and diffusion coefficients vary with the applied potential.
Morphology is a key element in the functionality of low dimensional structures including here electroactive polymers, especially when applications such as muscle like actuators are sought. The reason is that morphology in the context of a high specific surface object strongly influences specific parameters such as ionic diffusion, conductivity and consequently the actuation capability of the system. In the present work a new architecture for microtube-based actuating elements is presented. Free-standing fibrillar microtubes with diameter in the range of micrometers and with a core–shell polyaniline/gold structure are fabricated through a scalable approach. Aligned electrospun poly(methyl methacrylate) fibers are coated with gold and are further employed as microstructured electrodes for the electrochemical deposition of polyaniline. Further the poly(methyl methacrylate) core was dissolved, leading to a tubular structure. The polyaniline/gold microtubes show complex, rapid and reversible movement patterns, with great stability and consistency over repeated actuation cycles. Thus, when the potential is swept between −0.2 and 1V at different rates, the microtubes move, this movement being associated with the morphological and structural characteristics of the deposited polyaniline layer, a mechanism based on the expansion/contraction and conformational changes of the polymer chains due to the insertion/expulsion of ions. The response time of these electroactive microstructures during one cycle is in the range of seconds, a consequence of their low dimensionality and specific structure. Moreover the actuation takes place in different electrolytes including simulated gastric fluid, which enables a wide range of applications.
The development of soft actuators by using inexpensive raw materials and straightforward fabrication techniques, aiming at creating and developing muscle like micromanipulators, represents an ...important challenge nowadays. Providing such devices with biomimetic qualities, for example, sensing different external stimuli, adds even more complexity to the task. We developed electroactive polymer-coated microribbons that undergo conformational changes in response to external physical and chemical parameters. These were prepared following three simple steps. During the first step nylon-6/6 microribbons were fabricated by electrospinning. In a second step the microribbons were one side coated with a metallic layer. Finally, a conducting layer of polypyrrole was added by means of electrochemical deposition. Strips of polypyrrole-coated aligned microribbon meshes were tested as actuators responding to current, pH, and temperature. The electrochemical activity of the microstructured actuators was investigated by recording cyclic voltammograms. Chronopontentiograms for specific current, pH, and temperature values were obtained in electrolytes with different compositions. It was shown that, upon variation of the external stimulus, the actuator undergoes conformational changes due to the reduction processes of the polypyrrole layer. The ability of the actuator to hold and release thin wires, and to collect polystyrene microspheres from the bottom of the electrochemical cell, was also investigated.
Multiple and complex functionalities are a demand nowadays for almost all materials, including common day-to-day materials such as paper, textiles, wood, etc. In the present report, the surface ...temperature control of different types of materials, including paper and textiles, was demonstrated by Joule heating of metallic-web transparent electrodes both by direct current and by RF induced eddy currents. Polymeric submicronic fiber webs were prepared by electrospinning, and metal sputtering was subsequently performed to transform them into flexible transparent electrodes. These electrodes were thermally attached to different substrates, including paper, textiles and glass. Using thermochromic inks, we demonstrated a high degree of control of the substrates' surface temperature by means of the Joule effect. Metallic fiber webs appear to be excellently suited for use as transparent electrodes for controlling the surface temperature of common materials, their highly flexible nature being a major advantage when dealing with rough, bendable substrates. This kind of result could not be achieved on bendable substrates with rough surfaces such as paper or textiles while employing classical transparent electrodes i.e. metal oxides. Moreover, contactless heating with induced currents is a premiere for transparent electrodes and opens up a score of new application fields.
PDF
