Under the U.S. High Luminosity LHC Accelerator Upgrade Project (HL-LHC AUP), the 150 mm bore, high-field Nb 3 Sn low-β MQXFA quadrupole magnets are being fabricated, assembled and tested, in the ...context of the CERN Hi-Luminosity LHC (HL-LHC) upgrade. These magnets have 4.2 m magnetic length and 4.56 m long iron yoke. To date, eight MQXFA magnets have been tested. One of the magnets additionally underwent a successful endurance test with 40 triggered quenches, and two magnets did not perform as expected. This work summarizes for the first time the available strain gauge data from eight identical Nb 3 Sn MQXFA tested magnets, focusing on the endurance test, and on a possible cause of underperformance of the two magnets that did not pass the vertical test. We applied methods to prevent this from happening in future MQXFA magnets, which shown to be effective for last two tested magnets.
Hybrid magnets are currently under consideration as an economically viable option towards 20 T dipole magnets for next generation of particle accelerators. In these magnets, High Temperature ...Superconducting (HTS) materials are used in the high field part of the coil with so-called "insert coils", and Low Temperature Superconductors (LTS) like Nb 3 Sn and Nb-Ti superconductors are used in the lower field region with so-called "outsert coils". The attractiveness of the hybrid option lays on the fact that, on the one hand, the 20 T field level is beyond the Nb 3 Sn practical limits of 15-16 T for accelerator magnets and can be achieved only via HTS materials; on the other hand, the high cost of HTS superconductors compared to LTS superconductors makes it advantageous exploring a hybrid approach, where the HTS portion of the coil is minimized. We present in this paper an overview of different design options aimed at generating 20 T field in a 50 mm clear aperture. The coil layouts investigated include the Cos-theta design (CT), with its variations to reduce the conductor peak stress, namely the Canted Cos-theta design (CCT) and the Stress Management Cos-theta design (SMCT), and, in addition, the Block-type design (BL) including a form of stress management and the Common-Coil design (CC). Results from a magnetic and mechanical analysis are discussed, with particular focus on the comparison between the different options regarding quantity of superconducting material, field quality, conductor peak stress, and quench protection.
Within the U.S. Magnet Development Program, LBNL is planning to fabricate and test hybrid magnets combining Nb 3 Sn and Bi-2212 canted-cosine theta (CCT) magnets. The first planned hybrid magnet test ...integrates a 1 m long, 90 mm bore Nb 3 Sn dipole magnet (CCT5), and a 39 cm long, 30.8 mm bore Bi-2212 dipole magnet (BIN5c), which are already fabricated and were tested individually. The second planned hybrid magnet test integrates a 1.5 m long, 120 mm bore Nb 3 Sn dipole magnet (CCT6), still under design, and a 1 m long, 40 mm bore Bi-2212 dipole magnet (BiCCT1), which is under fabrication. This work gives an update of the status of the Bi-2212 CCT magnet program, and focuses on the first hybrid magnet (CCT5/BIN5c). The electromagnetic and mechanical analysis of the CCT5/BIN5c hybrid magnet is presented, as well as the proposed mechanical assembly process. The quench protection strategy associated with the hybrid magnet test is also presented.
The U.S. High-Luminosity LHC Accelerator Upgrade Project (HL-LHC AUP) has, in the recent years, developed assembly specifications for the 4.5 m long MQXFA magnets, which are 150 mm aperture ...high-field Nb 3 Sn low-β quadrupole magnets that are being built for the CERN Hi-Luminosity LHC (HL-LHC) upgrade. While the specifications were based on lessons learned from the LHC Accelerator Research Program (LARP) effort and the MQXFS and MQXFA prototype magnets, the experience gained from having both MQXFA07 and MQXFA08 magnets not meeting performance specifications during cold testing actually catalyzed a better understanding of the impact of the target assembly specifications and a subsequent refinement of the same. This paper summarizes a body of assembly data from the Pre-Series (MQXFA03-MQXFA07) and Series magnets (MQXFA08-MQXFA11) that have been built to date, and discusses the processes employed to successfully face the challenge of ensuring that the assembly specifications are met for the duration of the project.
The High Luminosity LHC (HL-LHC) Project is planning to install 16 cold-masses made with Nb 3 Sn quadrupole magnets in the LHC Interaction Regions to significantly increase its luminosity. Half of ...these cold masses are fabricated at BNL, FNAL, and LBNL under the US Accelerator Research Program (AUP). Each cold mass includes two identical Nb 3 Sn quadrupole magnets, called MQXFA with a magnetic length of 4.2 m. Currently, the AUP project has completed the fabrication and test of the first 5 pre-series magnets, and is working on the following 16 magnets for the series production. The brittleness and strain sensitivity of the Nb 3 Sn superconducting material requires a careful definition of the allowable maximum stress in the windings during magnet assembly and pre-load, and a tight control of their variation within the whole coil length. Therefore, a series of assembly and pre-load specifications have been defined with the goals of minimizing the risk of conductor degradation and providing the mechanical support required to reach the nominal current during powering. In this paper we present the specifications defined for the MQXFA magnets and applied during the different assembly phases and during the pre-load process of the first 5 pre-series magnets.
Towards 20 T Hybrid Accelerator Dipole Magnets Ferracin, P.; Ambrosio, G.; Arbelaez, D. ...
IEEE transactions on applied superconductivity,
09/2022, Letnik:
32, Številka:
6
Journal Article
Recenzirano
Odprti dostop
The most effective way to achieve very high collision energies in a circular particle accelerator is to maximize the field strength of the main bending dipoles. In dipole magnets using Nb-Ti ...superconductor the practical field limit is considered to be 8-9 T. When Nb 3 Sn superconductor material is utilized, a field level of 15-16 T can be achieved. To further push the magnetic field beyond the Nb 3 Sn limits, High Temperature Superconductors (HTS) need to be considered in the magnet design. The most promising HTS materials for particle accelerator magnets are Bi2212 and REBCO. However, their outstanding performance comes with a significantly higher cost. Therefore, an economically viable option towards 20 T dipole magnets could consist in an "hybrid" solution, where both HTS and Nb 3 Sn materials are used. We discuss in this paper preliminary conceptual designs of various 20 T hybrid magnet concepts. After the definition of the overall design criteria, the coil dimensions and parameters are investigated with finite element models based on simple sector coils. Preliminary 2D cross-section computation results are then presented and three main layouts compared: cos-theta, block, and common-coil. Both traditional designs and more advanced stress-management options are considered.
► CFD simulations of a variable geometry turbine under steady and pulsating flow. ► Most accumulations effects occur in the volute which also averages pressure pulses. ► Flow detachment around the ...nozzles blades leads to hysteretic effects in the stator. ► Rotor flow capacity is quasi-steady, but torque depends on the inflow conditions. ► A simple turbine model is proposed and agrees well with the CFD results.
This paper presents a numerical study analyzing the effect of pulsating flow in a variable geometry radial inflow turbine. The turbine behavior is analyzed under isentropic pulses, which are similar to those created by a rotating disk in a turbocharger test rig. Three different pulse frequencies (50, 90 and 130Hz) and two pulse amplitudes (100 and 180kPa) were considered. Turbine flow was studied throughout the pressure pulsation cycles in a wide range of off-design operating conditions, from low pressure ratio flow detachment to high pressure ratio choked flow. An overall analysis of the phasing of instantaneous mass flow and pressure ratio was first performed and the results show the non-quasi-steady behavior of the turbine as a whole as described in the literature. However, the analysis of the flow in the different turbine components independently gives a different picture. As the turbine volute has greater length and volume than the other components, it is the main source of non-quasi-steadiness of the turbine. The stator nozzles cause fewer accumulation effects than the volute, but present a small degree of hysteretic behavior due to flow separation and reattachment cycle around the vanes. Finally, the flow in the moving rotor behaves as quasi-steady, as far as flow capacity is concerned, although the momentum transfer between exhaust gas and blades (and thus work production and thermal efficiency) is affected by a hysteretic cycle against pressure ratio, but not if blade speed ratio is considered instead. A simple model to simulate the turbine stator and rotor is proposed, based on the results obtained from the CFD computations.
High-temperature superconducting <inline-formula><tex-math notation="LaTeX">\rm{REBa}_{2} Cu_{3} O_{7-x}</tex-math></inline-formula> ( REBCO ) conductors have the potential to generate a high ...magnetic field over a broad temperature range. The corresponding accelerator magnet technology, still in its infancy, can be attractive for future energy-frontier particle colliders such as a multi-TeV muon collider. To help develop the technology, we explore the requirements and potential characteristics of a REBCO magnet, operating at 4.2 or 20 K, with a dipole field of 8 - 10 T in a clear aperture of 150 mm. We use the canted <inline-formula><tex-math notation="LaTeX">\cos \theta</tex-math></inline-formula> magnet configuration to reduce the electromagnetic stresses on the conductors. We present the resulting dipole fields, field gradients for combined-function cases, conductor stresses, magnet dimensions and conductor lengths. We also discuss the conductor performance that is required to achieve the target dipole field at 4.2 and 20 K. The information can provide useful input to the development of REBCO magnet and conductor technology for collider-ring magnets in a muon collider.
The fruit fly
Anastrepha obliqua
is an economically important pest. The sterile insect technique to control it involves mass production and release of sterile flies to reduce the reproduction of the ...wild population. As noted in different Tephritidae, the performance of sterile males may be affected by the assimilation of nutrients under mass-rearing conditions. In the wild, the fly's life cycle suggests the acquisition of different organisms that could modulate its fitness and physiology. For
A
.
obliqua
, there is no information regarding microorganisms other than bacteria. This study analyzed bacteria, fungal, and archaea communities in the
A
.
obliqua
gut through denaturing gradient gel electrophoresis (DGGE) profiles of 16S (using a different set of primers for bacteria and archaea) and 18S ribosomal DNA markers. We found that wild flies presented higher microbial diversity related to fructose assimilation than laboratory species, suggesting that microorganisms have led to a specialized metabolism to process nutrients associated with an artificial diet. We identified species that have not been previously described in this fruit fly, especially actinobacteria and archaea, by employing different primer sets aimed at the same molecular marker but targeting diverse hypervariable regions of 16S rDNA. The possibility that Archaea affect fly fitness should not be ignored. This report on the intestinal microbial (bacteria, archaea, and fungi) composition of
A
.
obliqua
contributes to our understanding of the role of microorganisms in the development and physiology of the flies.
In high field magnet applications, Nb 3 Sn coils undergo a heat treatment step after winding. During this stage, coils radially expand and longitudinally contract due to the Nb 3 Sn phase change. In ...order to prevent residual strain from altering superconducting performances, the tooling must provide the adequate space for these dimensional changes. The aim of this paper is to understand the behavior of cable dimensions during heat treatment and to provide estimates of the space to be accommodated in the tooling for coil expansion and contraction. This paper summarizes measurements of dimensional changes on strands, single Rutherford cables, cable stacks, and coils performed between 2013 and 2015. These samples and coils have been performed within a collaboration between CERN and the U.S. LHC Accelerator Research Program to develop Nb 3 Sn quadrupole magnets for the HiLumi LHC. The results are also compared with other high field magnet projects.
PDF
