The high luminosity LHC (HL-LHC) project is aimed at studying and implementing the necessary changes in the LHC to increase its luminosity by a factor of five. Among the magnets that will be upgraded ...are the 16 superconducting low-β quadrupoles placed around the two high luminosity interaction regions (ATLAS and CMS experiments). In the current baseline scenario, these quadrupole magnets will have to generate a gradient of 140 T/m in a coil aperture of 150 mm. The resulting conductor peak field of more than 12 T will require the use of Nb 3 Sn superconducting coils. We present in this paper the HL-LHC low-β quadrupole design, based on the experience gathered by the US LARP program, and, in particular, we describe the support structure components to pre-load the coils, withstand the electro-magnetic forces, provide alignment and LHe containment, and integrate the cold mass in the LHC IRs.
HL-LHC IT STRING: Status and Perspectives Bajko, M.; Baglin, V.; Ballarino, A. ...
IEEE transactions on applied superconductivity,
08/2024, Letnik:
34, Številka:
5
Journal Article
Recenzirano
Odprti dostop
The HL-LHC IT STRING, an integrated test stand for the major components of the HL-LHC Inner Triplet (IT) zone, is in its construction phase in a surface building at CERN. The main motivation is to ...study and validate the collective behavior of the different systems: magnets, circuit protection, cryogenics for magnets and superconducting link, magnet powering, vacuum, alignment, and interconnections between magnets and superconducting link. During the past two years, the major focus has been on the technical infrastructure definition and implementation, while preparing the installation sequences and procedures for the major elements. The String Validation Program (SVP) has been agreed with the HL-LHC Work Packages, allowing to set up a joint and optimized test program and to integrate it in a schedule. In this paper we describe the IT String installations and describe the main differences between the HL-LHC IT String and the future HL-LHC machine. The main line of the test program and the motivation of a full thermal cycle with a cost benefit analysis will be presented.
CERN and INFN, Italy, have signed an agreement for R&D activities relating to high-luminosity LHC superconducting magnets, which include the design, construction, and cryogenic test of a set of five ...prototypes, one for each type foreseen, from the skew quadrupole to the dodecapole. The reference layout of these magnets is based on a superferric design type, which allows reaching the required integrated field strength with a relatively simple design. Since the number of magnets of all the types required for the series is 36, emphasis has been put on modularity, reliability, ease of construction, and on the use of an available superconducting wire. This paper presents the status of the development work being performed at INFN, LASA Laboratory, and at CERN, focusing on the following issues: the electromagnetic 2- and 3-D design including harmonic component study; the fringe field analysis; the magnet powering and quench protection; mechanical and construction main choices.
The High-Luminosity target neutral beam absorber (TAXN) is the radiation absorber of the neutral particle debris generated at the beam collisions carried out in the ATLAS and CMS detectors at the ...Large Hadron Collider (LHC). The new absorber will protect the superconducting magnets from this radiation to prevent their quenching at a design luminosity of7.5×1034cm−2s−1. This article describes the mechanical design of the TAXN assembly and the recombination chamber together with the thermal computations performed for the water-cooling and bakeout system prepared for the engineering design review held in January, 2021. It takes into account the internal integration of the zero degree calorimeter and beam rate of neutrals luminosity detector as well as their physics case overview. In addition, it provides the beam aperture breakdown and the heat deposition expected in the absorber.
The National Institute for Nuclear Physics (INFN) is developing, within the framework of a collaboration agreement with the European Organization for Nuclear Research (CERN), prototypes of five ...corrector magnets, from skew quadrupoles to dodecapoles, which will equip the high-luminosity interaction regions of the high-luminosity Large Hadron Collider. These magnets are based on a superferric design, which allows a relatively simple, modular, and easy-to-construct magnet. In this paper, we review the main features of the corrector magnets, and we present the results of the manufacture of the sextupole superconducting coils, from the development of suitable solutions for the winding and impregnation to the quality assessment on the series coils, including the results of the first cryogenic tests on a single coil.
After an overview of the radiation hardness needs for the normal conducting magnets installed in the present Large Hadron Collider (LHC) and for the future high-luminosity LHC (HL-LHC) exploitation, ...this paper describes the tests and modifications that have been carried out on the presently installed magnet types to evaluate their reliability and enhance their lifespan. In spite of the ongoing optimization, it has become evident that to comply with the HL-LHC requirement, new radiation hard magnets will be necessary for the most exposed locations: The solutions under study and the possible approaches will be discussed.
During 2016, one-quarter of the LHC main dipoles have has been powered above the 7.7 T operational field, to reach a field of 8.1 T. These tests were done to confirm the extrapolation of the training ...behavior based on a Gaussian tail of the quench distribution. In this paper, it is shown that a modified Gaussian distribution can be used to better model the quench distributions. We then present the data above 6.5 TeV, showing that they are compatible with the previous expectations. We present the data of retraining of sector 12, which was warmed up in 2016 to replace a magnet, and training of individual magnets that went through several thermal cycles: there is an indication that training campaigns during successive warm-ups and cool-downs could become shorter. We finally show that a significant correlation is found between the training of the installed magnet and individual test after a thermal cycle (second cool-down). On the other hand, no correlation is found with individual test under virgin conditions (first cool-down).
The Large Hadron Collider (LHC) main interconnection splices consist of Rutherford-type cable splice and busbar stabilizer splices. Busbar stabilizer splices have been consolidated during the first ...long LHC shutdown by soldering additional Cu shunts. In view of the large number of quality controls (QCs) that were integrated in the splice consolidation process, efficient and unambiguous QC procedures needed to be developed. Direct-current electrical resistance measurements have been selected for the control of the busbar splices and the individual shunts. About 400 000 resistance measurements performed at room temperature before and after each consolidation step have been analyzed. The resistance of the consolidated splices is comparable with the resistance of continuous busbars without splice. Resistance changes during the consolidation process correspond to those calculated from the changes in Cu cross-sectional area.
The design and construction of a wide-aperture, superconducting quadrupole magnet for the LHC insertion region is part of a study towards a luminosity upgrade of the LHC at CERN. The engineering ...design of components and tooling, the procurement, and the construction work presented in this paper includes innovative features such as more porous cable insulation, a new collar structure allowing horizontal assembly with a hydraulic collaring press, tuning shims for the adjustment of field quality, a fishbone like structure for the ground-plane insulation, and an improved quench-heater design. Rapid prototyping of coil-end spacers and trial-coil winding led to improved shapes, thus avoiding the need to impregnate the ends with epoxy resin, which would block the circulation of helium. The magnet construction follows established procedures for the curing and assembly of the coils, in order to match the workflow established in CERN's "large magnet facility." This requirement led to the design and procurement of a hydraulic press allowing for both a vertical and a horizontal position of the coil-collar pack, as well as a collapsible assembly mandrel, which guarantees the pack's four-fold symmetry during collaring. The assembly process has been validated with the construction of two short models, instrumented with strain gauges and capacitive pressure transducers. This also determines the final parameters for coil curing and shim sizes.
PDF
