The field of terahertz and millimeter wave science and technology has evolved in recent years into an area attracting a lot of attention from all sides of science, industry, and the public ....
We present observations of parasitic frequency components in the emission spectrum of typical photomixer sources for continuous wave (CW) terahertz generation. Broadband tunable photomixer systems ...are often used in combination with direct power detectors, e.g., for source and/or detector characterization. Here, spectral components besides the intended terahertz emission at the difference frequency of the two excitation lasers can significantly distort the measurement results. In this work, the appearance of parasitic mixing signals is observed in broadband measurements with a broadband antenna-coupled field-effect transistor as terahertz detector (TeraFET). The measurements reveal weaker spectral absorption features than expected and also a signal plateau towards higher frequencies, both strongly indicating a background in the detection signals. The photomixer emission is investigated in detail with a terahertz Fourier-transform infrared spectrometer (FTIR). We relate the observed parasitic frequency components with good quantitative agreement with the mode spectra of the semiconductor lasers. We also present one possible approach to overcome some of the issues, and we emphasize the importance of our findings to avoid distorted measurement results. To our knowledge, the essential aspect of parasitic mixing has so far been largely ignored in the literature where terahertz CW photomixer emitters are widely used for spectrally resolved measurements.
The 3D range-migration algorithm (RMA) and its 2D equivalent, the omega-k algorithm, are employed in a wide range of applications where reconstruction of synthetic aperture data is required, from ...satellite radar imaging of planets over seismic imaging of the earth crust, down to phased-array ultrasound and ultrasonic application, and recently in-line synthetic aperture radar for non-destructive testing. These algorithms are based on Fourier transforms and share their time-complexity. This limits highly-resolved measurement data to be processed at high speeds which would be advantageous for modern production feed lines. In this publication, we present the development and implementation of the RMA on a quantum computer that scales favourably compared to the time complexity of the classical RMA. We compare reconstruction results of simulated and measured data of the classical and quantum RMA. Hereby, the quantum RMA is run on a quantum simulator backend as well as on IBM's Q System One quantum computer. The results show that real world applications and testing tasks may benefit from future quantum computers.
Terahertz tomography is a promising method among non-destructive inspection techniques to detect faults and defects in dielectric samples. Recently, image quality was improved significantly through ...the incorporation of
information and off-axis data. However, this improvement has come at the cost of increased measurement time. To aim toward industrial applications, it is therefore necessary to speed up the measurement by parallelizing the data acquisition employing multi-channel setups. In this work, we present two tomographic frequency-modulated continuous wave (FMCW) systems working at a bandwidth of 230-320 GHz, equipped with an eight-channel detector array, and we compare their imaging results with those of a single-pixel setup. While in the first system the additional channels are used exclusively to detect radiation refracted by the sample, the second system features an f-θ lens, focusing the beam at different positions on its flat focal plane, and thus utilizing the whole detector array directly. The usage of the f-θ lens in combination with a scanning mirror eliminates the necessity of the formerly used slow translation of a single-pixel transmitter. This opens up the potential for a significant increase in acquisition speed, in our case by a factor of four to five, respectively.
We present a rotational terahertz imaging system for inline nondestructive testing (NDT) of press sleeves for the paper industry during fabrication. Press sleeves often consist of polyurethane (PU) ...which is deposited by rotational molding on metal barrels and its outer surface mechanically processed in several milling steps afterwards. Due to a stabilizing polyester fiber mesh inlay, small defects can form on the sleeve's backside already during the initial molding, however, they cannot be visually inspected until the whole production processes is completed. We have developed a fast-scanning frequenc-modulated continuous wave (FMCW) terahertz imaging system, which can be integrated into the manufacturing process to yield high resolution images of the press sleeves and therefore can help to visualize hidden structural defects at an early stage of fabrication. This can save valuable time and resources during the production process. Our terahertz system can record images at 0.3 and 0.5 THz and we achieve data acquisition rates of at least 20 kHz, exploiting the fast rotational speed of the barrels during production to yield sub-millimeter image resolution. The potential of automated defect recognition by a simple machine learning approach for anomaly detection is also demonstrated and discussed.
We present thickness measurements with millimeter and terahertz waves using frequency-modulated continuous-wave (FMCW) sensors. In contrast to terahertz time-domain spectroscopy (TDS), our FMCW ...systems provide a higher penetration depth and measurement rates of several kilohertz at frequency modulation bandwidths of up to 175 GHz. In order to resolve thicknesses below the Rayleigh resolution limit given by the modulation bandwidth, we employed a model-based signal processing technique. Within this contribution, we analyzed the influence of multiple reflections adapting a modified transfer matrix method. Based on a brute force optimization, we processed the models and compared them with the measured signal in parallel on a graphics processing unit, which allows fast calculations in less than 1 s. TDS measurements were used for the validation of our results on industrial samples. Finally, we present results obtained with reduced frequency modulation bandwidths, opening the window to future miniaturization based on monolithic microwave integrated circuit (MMIC) radar units.
Terahertz tomography is a non-contact inspection technique to image objects from multiple angles and reconstruct their 3D volume from intensity and time-of-flight transmission data, without the need ...for radiation protection measures. Unlike X-rays, terahertz radiation is subject to strong diffraction and refraction when propagating through dielectric materials, which often deteriorate the image reconstruction quality. Our solution to this problem applies ray tracing, considering the beam shape and an a priori model of the sample under investigation to predict the beam paths of the terahertz radiation. We present two reconstruction methods based on the resulting beam path predictions yielding higher image quality. Method 1 filters out beams deviating strongly, thus removing induced artifacts and errors from the reconstruction image. Method 2 employs off-axis measurements that acquire data along the full detection plane and in this way detect even strongly deflected beams. Considering these beams and the information they carry in the reconstruction enhances the image quality. Applying these methods to terahertz tomography, even complicated structures can be imaged. We display the significant enhancements achieved with the two methods by comparing the reconstruction results of different polymeric samples.
Terahertz tomography allows for non-contact tomographic inspection of dielectric materials without the need for radiation protection measures. Terahertz tomography offers the opportunity to inspect ...such objects from multiple angles not only by measuring the absorption but also by acquiring the time-of-flight of the radiation. Hence, this technique facilitates the reconstruction of the complete complex refractive index of a sample under test. Even complicated surface structures can be imaged, provided the feature size is above the diffraction limit roughly given by the wavelength of the terahertz radiation in use. For industrial applications, computational efficiency and imaging performance are crucial. Therefore, we apply the iterative conjugate gradient least square (CGLS) algorithm to reconstruct images from terahertz tomography data. To ensure reliable convergence of this semi-convergent CGLS algorithm a stopping mechanism based on the L-curve criterion is implemented. The result is a fast-converging, parallelizable method, which offers the flexibility to adapt to the specifics of terahertz tomography. As an example of this adaptability, we implement a non-negativity constraint, suppressing noise in the image and significantly enhancing reconstruction quality.
A millimeter-wave (mmW) classifier system applied to images synthesized from a coded-aperture based computational imaging (CI) radar is presented. A developed physical model of a CI system is used to ...generate the image dataset for the classification algorithm. A convolutional neural network (CNN) is integrated with the physical model and trained using the dataset comprising of synthesized mmW images obtained directly from the developed CI physical model. A <inline-formula> <tex-math notation="LaTeX">{k} </tex-math></inline-formula>-fold cross validation technique is applied during the training process to validate the classification model. The coded-aperture CI concept enables image reconstruction from a significantly reduced number of back-scattered measurements by facilitating physical layer compression. This physical layer compression can substantially simplify the data acquisition layer of imaging radars, which is realized using only two channels in this article. The integration of the classification algorithm with the CI numerical model is particularly important in enabling the training step to be carried out using relevant system metrics and without the necessity for experimental data. Leveraging the CI numerical model generated data, training step for the classification algorithm is achieved in real-time while also confirming that the numerically trained CI classifier offers high accuracy with both simulated and experimental data. The classifier integrated physical model also enables performance analysis of the classification algorithm to be carried out as a function of key system metrics such as signal-to-noise (SNR) level, ensuring a complete understanding of the classification accuracy under different operating conditions. The trained CI system is tested with synthesized mmW images from the physical model and a classification accuracy of 89% is achieved. The proposed model is also verified using experimental data validating the fidelity of the developed CI integrated classifier system. A classification latency of 3.8 ms per frame is achieved, paving the way for real-time automated threat detection (ATD) for security-screening applications.
Radomes protecting sensitive radar, navigational, and communications equipment of, e.g., aircraft, are strongly exposed to the environment and have to withstand harsh weather conditions and potential ...impacts. Besides their significance to the structural integrity of the radomes, it is often crucial to optimize the composite structures for best possible radio performance. Hence, there exists a significant interest in non-destructive testing techniques, which can be used for defect inspection of radomes in field use as well as for quality inspection during the manufacturing process. Contactless millimeter-wave and terahertz imaging techniques provide millimeter resolution and have the potential to address both application scenarios. We report on our development of a three-dimensional (3D) terahertz imaging system for radome inspection during industrial manufacturing processes. The system was designed for operation within a machining center for radome manufacturing. It simultaneously gathers terahertz depth information in adjacent frequency ranges, from 70 to 110 GHz and from 110 to 170 GHz by combining two frequency modulated continuous-wave terahertz sensing units into a single measurement device. Results from spiraliform image acquisition of a radome test sample demonstrate the successful integration of the measurement system.
PDF
