Interferometric gravitational-wave detectors like LIGO need to be able to measure changes in their arm lengths of order 10−18 m or smaller. This requires very high laser power in order to raise the ...signal above shot noise. One significant limitation to increased laser power is an optomechanical interaction between the laser field and the detector's test masses that can form an unstable feedback loop. Such parametric instabilities have long been studied as a limiting effect at high power, and were first observed to occur in LIGO in 2014. Since then, passive and active means have been used to avoid these instabilities, though at power levels well below the final design value. Here we report on the successful implementation of tuned, passive dampers to tame parametric instabilities in LIGO. These dampers are applied directly to all interferometer test masses to reduce the quality factors of their internal vibrational modes, while adding a negligible amount of noise to the gravitational-wave output. In accordance with our model, the measured mode quality factors have been reduced by at least a factor of 10 with no visible increase in the interferometer's thermal noise level. We project that these dampers should remove most of the parametric instabilities in LIGO when operating at full power, while limiting the concomitant increase in thermal noise to approximately 1%.
The first detection of gravitational waves by the Laser Interferometer Gravitational-Wave Observatory (LIGO) in 2015 launched the era of gravitational-wave astronomy. The quest for gravitational-wave ...signals from objects that are fainter or farther away impels technological advances to realize ever more sensitive detectors. Since 2019, one advanced technique, the injection of squeezed states of light, is being used to improve the shot-noise limit to the sensitivity of the Advanced LIGO detectors, at frequencies above ∼50 Hz. Below this frequency, quantum backaction, in the form of radiation pressure induced motion of the mirrors, degrades the sensitivity. To simultaneously reduce shot noise at high frequencies and quantum radiation pressure noise at low frequencies requires a quantum noise filter cavity with low optical losses to rotate the squeezed quadrature as a function of frequency. We report on the observation of frequency-dependent squeezed quadrature rotation with rotation frequency of 30 Hz, using a 16-m-long filter cavity. A novel control scheme is developed for this frequency-dependent squeezed vacuum source, and the results presented here demonstrate that a low-loss filter cavity can achieve the squeezed quadrature rotation necessary for the next planned upgrade to Advanced LIGO, known as "A+."
The Advanced Laser Interferometer Gravitational-wave Observatory (LIGO) detectors have completed their initial upgrade phase and will enter the first observing run in late 2015, with detector ...sensitivity expected to improve in future runs. Through the combined efforts of on-site commissioners and the Detector Characterization Group of the LIGO Scientific Collaboration, interferometer performance, in terms of data quality, at both LIGO observatories has vastly improved from the start of commissioning efforts to present. Advanced LIGO has already surpassed Enhanced LIGO in sensitivity, and the rate of noise transients, which would negatively impact astrophysical searches, has improved. Here we give details of some of the work which has taken place to better the quality of the LIGO data ahead of the first observing run.
We present a simple feedback description of parametric instabilities which can be applied to a variety of optical systems. Parametric instabilities are of particular interest to the field of ...gravitational-wave interferometry where high mechanical quality factors and a large amount of stored optical power have the potential for instability. In our use of Advanced LIGO as an example application, we find that parametric instabilities, if left unaddressed, present a potential threat to the stability of high-power operation.
The advanced LIGO detectors are currently in their final design stage, and the installation phase will start at the end of 2010: they will have about 10 times better sensitivity than initial LIGO, ...with a sensitive band ranging from 10 Hz to 10 kHz. As compared with previous LIGO detectors, there will be increased complexity in the optical configuration, improved seismic isolation system and significantly higher power circulating in the arm cavities. In the new detectors, the control of the angular orientation of the mirrors will be particularly challenging. The advanced LIGO (aLIGO) mirrors need to have a residual angular motion of the order of 1 nrad RMS in order to achieve high sensitivity. In the high power regime, the torque induced by radiation pressure effects will be comparable with the restoring torque of the mirror suspension, such that we must think of the opto-mechanical response, instead of just the mechanical response. These modifications have to be considered in order to design the control strategy for keeping the mirrors well aligned. Moreover, to meet the sensitivity target the alignment control noise coupled to the gravitational-wave channel must be well below at 10 Hz. We developed a model of the alignment sensing and control scheme of aLIGO which takes into account radiation pressure effects and meets the noise target.
We present a new approach for characterizing the loss factor of materials, using a suspended mechanical oscillator. Compared to more standard techniques, this method offers freedom in terms of the ...size and shape of the tested samples. Using a finite element model and the vibration measurements, the loss factor is deduced from the oscillator's ring-down. In this way the loss factor can be estimated independently for shear and compression deformation of the sample over a range of frequencies. As a proof of concept, we present measurements for EPO-TEK 353ND epoxy samples.
PDF
