A comprehensive cost correlation analysis was conducted based on available cost correlations, and new equipment cost correlation models were proposed based on QUE$TOR modeling. Cost correlations for ...various types of equipment such as pumps, compressors, heat exchangers, air coolers, and pressure vessels were generated on the basis of extracted cost data. The models were derived on the basis of robust multivariable regression with the aim of minimizing the residuals by using the genetic algorithm. The proposed compressor models for both centrifugal and reciprocating types showed that the Turton cost estimation for carbon steel compressor and Matche’s and Mhhe’s data were compatible with the generated model. According to the results, the cost trend in the Turton correlation for carbon steel had a somewhat lower estimation than these correlations. Further, the cost trend of the Turton correlation for carbon steel pressure vessels was close to the presented model trend for both bullet and sphere types. The Turton cost trend for U-tube shell-and-tube heat exchangers with carbon steel shell and stainless steel tube was close to the proposed heat exchanger model. Furthermore, the Turton cost trend for the flat-plate heat exchanger using carbon steel was similar to the proposed model with a slight difference.
A Thermo-Electric Energy Storage (TEES) system is proposed to provide peak-load support (1–2 daily hours of operation) for distributed users using small/medium-size photovoltaic systems (4 to 50 ...kWe). The purpose is to complement the PV with a reliable storage system that cancompensate the produc tivity/load mismatch, aiming at off-grid operation. The proposed TEES applies sensible heat storage, using insulated warm-water reservoirs at 120/160 °C, and cold storage at −10/−20 °C (water and ethylene glycol). The power cycle is a trans-critical CO2 unit including recuperation; in the storage mode, a supercritical heat pump restores heat to the hot reservoir, while a cooling cycle cools the cold reservoir; both the heat pump and cooling cycle operate on photovoltaic (PV) energy, and benefit from solar heat integration at low–medium temperatures (80–120 °C). This allows the achievement of a marginal round-trip efficiency (electric-to-electric) in the range of 50% (not considering solar heat integration).The TEES system is analysed with different resource conditions and parameters settings (hot storage temperature, pressure levels for all cycles, ambient temperature, etc.), making reference to standard days of each month of the year; exergy and exergo-economic analyses are performed to identify the critical items in the complete system and the cost of stored electricity.
Oscillating water column (OWC) systems are among the most credited solutions for an effective conversion of the notable energy potential conveyed by sea waves. Despite a renewed interest, however, ...they are often still at a demonstration phase and additional research is required to reach industrial maturity. Within this framework, this study provides a wave-to-wire model for OWC systems based on an impulse air turbine. The model performs a comprehensive simulation of the system to estimate the attendant electric energy production for a specific sea state, based on analytical models of the primary (fixed chamber) and secondary (air turbine) converters coupled with the tertiary converter (electric generator). A rigid piston model is proposed to solve the hydrodynamics, thermodynamics, and hydrodynamics of the chamber, in a coupled fashion with the impulse turbine aerodynamics. This is solved with a novel method by considering the cascades as sets of blades, each one consisting of a finite number of airfoils stacked in the radial direction. The model was applied for two Mediterranean sites located in Tuscany and Sardinia (Italy), which were selected to define the optimal geometry of the turbine for a specified chamber. For each system, the developed analytical wave-to-wire model was applied to calculate the performance parameters and the annual energy production in environmental conditions typical of the Mediterranean Sea. The selected impulse turbines are able to convert 13.69 and 39.36 MWh/year, with an efficiency of 4.95% and 4.76%, respectively, thus proving the interesting prospects of the technology.
The Hellisheidi geothermal power plant, located in Iceland, is a combined heat and power double-flash geothermal plant with an installed capacity of 303.3 MW of electricity and 133 MW of hot water. ...This study aimed to elucidate the environmental impacts of the electricity and heat production from this double-flash geothermal power plant. In this vein, firstly, the most updated inventory of the plant was generated, and secondly, a life-cycle assessment approach based on the exergy allocation factor was carried out instead of applying the traditionally used allocations in terms of mass and energy. The functional unit was defined as the production of 1 kWh of electricity and 1 kWh of hot water for district heating. The life-cycle stages included the (i) construction, (ii) operation (including abatement operations and maintenance), and (iii) well closure of the geothermal plant. All of the life-cycle stages from construction to dismantling were considered. Finally, the results on the partitioning of the environmental impact to electricity and heat with exergy allocations showed that most of the impact should be charged to electricity, as expected. Furthermore, the distribution of the environmental impacts among the life-cycle stages determined that the construction stage was the most impactful for the electricity and heat production. This result was attributable to the large consumption of steel that was demanded during the construction of the geothermal power plant (geothermal wells, equipment, and buildings). Impacts due to the abatement stage demonstrated that this stage satisfactorily reduced the total impact attributed to the three life-cycle stages of the geothermal power plant.
Geothermal energy is acknowledged globally as a renewable resource, which, unlike solar, wind or wave energy, can be continuously exploited. The geothermal fluids usually have some acid gas content, ...which needs to be precisely taken into account when predicting the actual potential of a power plant in dealing with an effective reinjection. One of the key parameters to assess is the solubility of the acid gas, as it influences the thermodynamic conditions (saturation pressure and temperature) of the fluid. Therefore, an enhanced solubility model for the CO2-H2S-water system is developed in this study, based on the mutual solubility of gases. The model covers a wide range of pressures and temperatures. The genetic algorithm is employed to calculate the correlation constants and corresponding solubility values of both CO2 and H2S as functions of pressure, temperature and the balance of the gas. The results are validated against previously published models and experimental data available in the literature. The proposed model estimates the pure gas solubility, which is also a feature of other models. The more innovative feature of the model is the solubility estimation of each CO2 or H2S in simultaneous presence, such as when the binary gas is injected into the pure water of the geothermal reinjection well. The proposed solubility model fits well with the available experimental data, with a mean deviation lower than 0.2%.
Geothermal energy could play a crucial role in the European energy market and future scenarios focused on sustainable development. Thanks to its constant supply of concentrated energy, it can support ...the transition towards a low-carbon economy. In the energy sector, the decision-making process should always be supported by a holistic science-based approach to allow a comprehensive environmental assessment of the technological system, such as the life cycle assessment (LCA) methodology. In the geothermal sector, the decision-making is particularly difficult due to the large variability of reported results on environmental performance across studies. This calls for harmonized guidelines on how to conduct LCAs of geothermal systems to enhance transparency and results comparability, by ensuring consistent methodological choices and providing indications for harmonized results reporting. This work identifies the main critical aspects of performing an LCA of geothermal systems and provides solutions and technical guidance to harmonize its application. The proposed methodological approach is based on experts’ knowledge from both the geothermal and LCA sectors. The recommendations cover all the life cycle phases of geothermal energy production (i.e., construction, operation, maintenance and end of life) as well as a selection of LCA key elements thus providing a thorough base for concerted LCA guidelines for the geothermal sector. The application of such harmonized LCA framework can ensure comparability among LCA results from different geothermal systems and other renewable energy technologies.
A detailed assessment of the cumulative cost of clean water production by a natural circulation solar thermal system is presented. The system is designed and sized for sufficient residence time for ...pasteurisation, in a buoyancy-driven self-compensating circuit. Since it does not consume electricity, it is suitable for developing countries or emergency locations with safe drinking water issues. The principles for design and off-design simulations are explained and discussed. The simulations were performed for seven different locations, representing variable climate conditions in selected regions where there is an evident need for safe water. The results include an exergy and exergo-economic analysis. The production capacity reaches typically from 0.04 to 0.1 m3/day per m2 of solar collector depending on the location. The annual cost of water production ranges between 2.2 and 6.8 €/m3 making the proposed system fairly competitive; the energy- and price-performance of the system is compared to a reverse osmosis/photovoltaic system, representing a high-tech alternative for the purpose of water purification.
Renewable energies are often subject to stochastic resources and daily cycles. Energy storage systems are consequently applied to provide a solution for the mismatch between power production ...possibility and its utilization period. In this study, a solar integrated thermo-electric energy storage (S-TEES) is analyzed both from an economic and environmental point of view. The analyzed power plant with energy storage includes three main cycles, a supercritical CO2 power cycle, a heat pump and a refrigeration cycle, indirectly connected by sensible heat storages. The hot reservoir is pressurized water at 120/160 °C, while the cold reservoir is a mixture of water and ethylene glycol, maintained at −10/−20 °C. Additionally, the power cycle’s evaporator section rests on a solar-heated intermediate temperature (95/40 °C) heat reservoir. Exergo-economic and exergo-environmental analyses are performed to identify the most critical components of the system and to obtain the levelized cost of electricity (LCOE), as well as the environmental indicators of the system. Both economic and environmental analyses revealed that solar energy converting devices are burdened with the highest impact indicators. According to the results of exergo-economic analysis, it turned out that average annual LCOE of S-TEES can be more than two times higher than the regular electricity prices. However, the true features of the S-TEES system should be only fully assessed if the economic results are balanced with environmental analysis. Life cycle assessment (LCA) revealed that the proposed S-TEES system has about two times lower environmental impact than referential hydrogen storage systems compared in the study.
The energy demand in healthcare and hospital premises has distinctive features. Due to specific constraints in terms of service continuity and indoor air quality, the demand is at a large extent ...constant during the day and throughout the year. Indeed, a healthcare facility must fulfil several different activities. Medical equipment needs electric energy, while the Heating, Ventilation and Air Conditioning systems require thermal energy. It is extremely difficult to define reference characteristics for the energy demand, since the proportions of the different consumptions are strongly connected with the specific activities/services carried out within each structure. The present work aims at analysing the energy demand of a healthcare facility located near Firenze (Italy). The energy demand has been analysed by means of the available documentation to get a basic knowledge of the expected consumption of each component of the facility. These data have been then correlated with information on the actual healthcare activity parameters (e.g. staff in service, medical services) and on weather conditions. As a result, the study led to the definition of the principal energy drivers that characterize the Healthcare Facility. The analysis procedure is thought of general interest for the community working in the field, representing a benchmark for the calibration of energy digital twins and a reference data set useful to carry out building energy efficiency optimization strategies.
Geothermal power plants (GPP) with high non condensable gases (NCG) content geothermal fluid have shown to be environmental impacting relating to their energy production, which could be critical if ...no corrective actions are achieved. The GPP of Kizildere 3 U1, located in Türkiye (Denizli), in where the geothermal fluid contains high percentage of CO2, 99% of the NCG fraction, which represents the 3% of the geothermal fluid mass, is taken as a relevant case study to implement a new innovation consisting of NCG reinjection to reduce the amount of NCGs released to the atmosphere. In order to calculate the present environmental impacts which the plant is causing (baseline); and the potential reduction of environmental impacts which can be achieved with the innovation (reinjection), a life cycle assessment (LCA) calculation were developed. Primary data were collected for all the relevant stages of the energy conversion cycle and complemented where necessary with secondary data from other geothermal power plants studies. The main results of the baseline environmental assessment show that the construction phase is the most impacting phase due to the materials used in the power plant building construction, electrical generation equipment and distributed machinery and infrastructures; the effects in the operation phase are dominated by the geothermal fluid composition. In this sense, the application of CO2 reinjection at the Turkish site into the reservoir will prevent the emission of 1,700 tons·year−1 in the pilot site and 10% of the total emissions released along the life span of the GPP.