Understanding the complexities associated with contact line dynamics on chemically heterogeneous and superhydrophobic surfaces is important for a wide variety of engineering problems. Despite ...significant efforts to capture the behavior of a droplet on these surfaces over the past few decades, modeling of the complex dynamics at the three-phase contact line is needed. In this work, we demonstrate that contact line distortion on heterogeneous and superhydrophobic surfaces is the key aspect that needs to be accounted for in the dynamic droplet models. Contact line distortions were visualized and modeled using a thermodynamic approach to develop a unified model for contact angle hysteresis on chemically heterogeneous and superhydrophobic surfaces. On a surface comprised of discrete wetting defects on an interconnected less wetting area, the advancing contact angle was determined to be independent of the defects, while the relative fraction of the distorted contact line with respect to the baseline surface was shown to govern the receding contact angle. This behavior reversed when the relative wettability of the discrete defects and interconnected area was inverted. The developed model showed good agreement with the experimental advancing and receding contact angles, both at low and high solid fractions. The thermodynamic model was further extended to demonstrate its capability to capture droplet shape evolution during liquid addition and removal in our experiments and those in literature. This study offers new insight extending the fundamental understanding of solid–liquid interactions required for design of advanced functional coatings for microfluidics, biological, manufacturing, and heat transfer applications.
Understanding of the molecular mechanisms of prostate cancer has led to development of therapeutic strategies targeting androgen receptor (AR). These androgen-receptor signaling inhibitors (ARSI) ...include androgen synthesis inhibitor-abiraterone and androgen receptor antagonists-enzalutamide, apalutamide, and darolutamide. Although these medications provide significant improvement in survival among men with prostate cancer, drug resistance develops in nearly all patients with time. This could be through androgen-dependent or androgen-independent mechanisms. Even weaker signals and non-canonical steroid ligands can activate AR in the presence of truncated AR-splice variants, AR overexpression, or activating mutations in AR. AR splice variant, AR-V7 is the most studied among these and is not targeted by available ARSIs. Non-androgen receptor dependent resistance mechanisms are mediated by activation of an alternative signaling pathway when AR is inhibited. DNA repair pathway, PI3K/AKT/mTOR pathway, BRAF-MAPK and Wnt signaling pathway and activation by glucocorticoid receptors can restore downstream signaling in prostate cancer by alternative proteins. Multiple clinical trials are underway exploring therapeutic strategies to overcome these resistance mechanisms.
Understanding liquid dynamics on surfaces can provide insight into nature's design and enable fine manipulation capability in biological, manufacturing, microfluidic and thermal management ...applications. Of particular interest is the ability to control the shape of the droplet contact area on the surface, which is typically circular on a smooth homogeneous surface. Here, we show the ability to tailor various droplet contact area shapes ranging from squares, rectangles, hexagons, octagons, to dodecagons via the design of the structure or chemical heterogeneity on the surface. We simultaneously obtain the necessary physical insights to develop a universal model for the three-dimensional droplet shape by characterizing the droplet side and top profiles. Furthermore, arrays of droplets with controlled shapes and high spatial resolution can be achieved using this approach. This liquid-based patterning strategy promises low-cost fabrication of integrated circuits, conductive patterns and bio-microarrays for high-density information storage and miniaturized biochips and biosensors, among others.
Sintering of tungsten nominally requires several hours at ultrahigh temperatures. We show this refractory metal can be sintered quickly by direct injection of current into dog bone shaped specimens. ...The current rate was varied from 10 A s−1 (fast) to 0.1 A s−1 (slow), leading to sintering in 2–200 s, respectively. Sintering occurred at the same current density, regardless of the current rate. In all instances, the samples sintered when they reached 1000°C. The phenomenological behavior of flash sintering of metals is described by three stages: an incubation time followed by electroluminescence, and finally by abrupt sintering to full density. It is conjectured that rapid sintering is instigated by the formation of Frenkel pairs (vacancies and interstitials), as well as electrons and holes. The point defects accelerate mass transport, whereas electrons and holes recombine to form photons. Calorimetric measurements show an endothermic reaction attributed to the creation of defects. Estimates suggest an unusually large concentration of Frenkel pairs. PS: Flash sintering is different than electro‐discharge‐sintering where a capacitor is discharged in a few milliseconds to sinter a metal. Here, instead of dumping large amount of energy at once, a power supply is programed to control the rate of current injection.
We show that cubic 8 mol% yttria (8YSZ) can be sintered at 750°C with the application of DC electrical fields; in comparison the lowest sintering temperature for 3YSZ was 850°C. Furthermore, cubic ...zirconia exhibits the onset of flash sintering at 30 V/cm, whereas 3YSZ begins flash sintering at 60 V/cm. However, the volume specific power dissipation for the onset of flash sintering remains similar at ∼10 mW/mm3. The easier sintering of 8YSZ is ascribed to its higher ionic conductivity.
We report, for first time, how electric fields influence the sintering of undoped BaTiO3, a ferroelectric material, and how this process affects the microstructure and the dielectric properties. ...Flash sintering is achieved at a furnace temperature of 688°C under a field of 500Vcm−1, producing specimens that are 94% dense. As a consequence, the grain size is much finer than in conventional sintering, which is shown to influence the Curie temperature and dielectric permittivity. Data obtained at different strengths of the electrical field, and current limits imposed on the specimen are presented in the form of a “processing map” that separates the safe region, where sintering is uniform, from the fail region, where the current flow in the sample becomes localized. The map illustrates that ceramics can respond by different mechanisms, with the dominant mechanism changing with the strength of the electrical parameters.
In‐situ flash experiments on rutile TiO2 were performed at the synchrotron at the Brookhaven National Laboratory. Pair distribution function analysis of total X‐ray scattering measurements yielded ...mean‐square atomic displacements of oxygen and titanium atoms during the progression of the 3 stages of flash. The displacements are measured to be far greater for oxygen atoms than for titanium atoms. These large displacements may signal an “elastic softening” of the lattice, which, recently, has been predicted as a precursor to the onset of flash.
Herein, inspired by
Acacia auriculiformis
fruit, the shish-kebab-like growth of ZnO on carbon urchin (ZnO@CU) was designed using microwave radiation, thus leading to a hierarchal 3D structure that ...can promote multiple internal reflections through polarization centers. This hierarchal structure was then dispersed in a designer polyetherimide (PEI) matrix containing dynamic covalent bonds that can undergo metathesis, triggered by temperature, to harness self-healing properties in the composite. Such key attributes are required for their potential use in EMI shielding applications where frequent repairs are indispensable. Morphological investigation revealed that the ZnO flower was periodically nucleated like shish-kebab structures on CU surfaces. CU was designed from short carbon fibers using a facile modified method. The EMI shielding performance of the resulting composites was investigated in the X-band, illustrating a shielding effectiveness of 40.6 dB for 2 wt% of ZnO@CU loading, and the composite can be preserved after the self-healing procedure. The ZnO 'kebabs' on CU shish' facilitated multiple scattering and numerous polarization centers to improve the EMI shielding performances at extremely low filler contents. In addition, the mechanical and thermal properties of the composite showed improved structural integrity and superior resistance to extreme temperatures, respectively. Overall, the proposed ZnO@CU/PEI composite has great potential to fulfill the increasing demands for lightweight EMI shielding materials in many fields.
Herein, inspired by
Acacia auriculiformis
fruit, the shish-kebab-like growth of ZnO on carbon urchin (ZnO@CU) was designed using microwave radiation, thus leading to a hierarchal 3D structure that can promote multiple internal reflections through polarization centers.
PDF
