U ovom su radu prikazani rezultati ispitivanja mikrostrukture kotača dizalice, kao i procedura navarivanja koja je uporabljena za popravak. Reparaturno navarivanje se sastojalo iz dodavanja navarenog ...sloja na kotač dizalice, koji je prethodno pretrpio oštećenja uslijed habanja. Detaljna analiza kontakta između tračnice i kotača provedena je za realne uvjete opterećenja, kao i pomoću numeričke simulacije, a na osnovu mehaničkih i kemjskih karakteristika materijala uporabljenih za izradu kotača, kao i za reparaturno navarivanje. Numeričke su simulacije provedene primjenom metode konačnih elemenata. Za potrebe analize, vrijednosti kontaktnih naprezanja između kotača dizalice i tračnice određene su prema Hertz-ovoj teoriji. Svi numerički modeli su rabljeni za analizu naprezanja za slučajeve s i bez pukotine u cilju određivanja utjecaja pukotine na integritet kotača dizalice, a dobiveni rezultati su upoređeni s teorijskim vrijednostima. Također, u obzir je uzeta i simetrija kontaktnog područka između kotača i tračnice, tj. napravljeni su numerički modeli sa simetričnom i asimetričnom pozicijom kontakta.
W pracy przedstawiono wyniki oceny makro- i mikrostruktury złączy zgrzewanych wybuchowo poddanych obróbce cieplnej. Materiałem podstawowym do wykonania platerów była stal niestopowa P355NH, a ...materiałami nakładanymi były stale austenityczne 316L i 254SMO oraz stal superduplex SAF2507. Ocenie poddano mikrostrukturę stali podłoża oraz nakładanych powłok ze szczególnym uwzględnieniem miejsca połączenia. Badania przeprowadzono na zgładach metalograficznych w przekroju poprzecznym złącza z wykorzystaniem mikroskopii świetlnej. Dodatkowo, w celu określenia właściwości mechanicznych złączy wykonano pomiary twardości. Evaluation of microstructure and selected mechanical properties of explosive welded joints after heat treatment Abstract The paper presents results of macro- and microstructure evaluation of explosive welded joints after heat treatment. As the base plate was non-alloyed steel – P355NH. The cladder plate were two austenitic steels (316L and 254SMO) and super duplex steel (SAF2507). The microstructure testing was carried out near to fusion line on the side of base plate and cladder plate. The evaluation was carried out in the cross sections of joints. To assess the mechanical properties changes before and after heat treatment, the hardness measurement was done.
W artykule przedstawiono próbę implantacyjną oceny skłonności do pęknięć zimnych złączy spawanych. Przedstawiono również wyniki próby dla stali 7CrMoVTiB10-10 oraz badania w zakresie oceny charakteru ...przełomu. Evaluation of susceptibility to cold cracking of welded joints in the implant test Abstract The paper presents the implant test method as useful for susceptibility to cold cracking evaluation of welded joints. Moreover, there are presented results of implant test for 7CrMoTiVB10-10 steel and fractures analyses with the use of light microscopy and scanning electron microscopy.
This work was planned to modify the microstructure of a solution-treated, cast Al-Si-Mg aluminum alloy by a plastic deformation method at a cryogenic temperature. It was found that cryo-rolling is an ...efficient low-temperature, plastic-deformation method that causes the transformation of a dendritic microstructure to an ultrafine-grained counterpart with a high dislocation density and the redistribution of hard silicon particles in the cast aluminum alloy. The results show cryo-rolling strains lead to an increment of the dislocation density because of the annihilation of the dislocations’ dynamic recovery. The microstructural refinement imposed by cryo-rolling seems to lead to a notable strength enhancement of the material because of the coupled impact of dislocation-strengthening and grain-boundary-strengthening mechanisms.
Plasma spray Cr2O3 ceramic layers are used as a separate coating or as a supplement to bio-reactive organic composite ceramics Ca10(PO4)6(OH)2-Al2O3-ZrO2-Cr2O3 and other bio-inert ceramics in ...composites of the types Al2O3–ZrO2–SrO–Cr2O3–Y2O3, ZrO2-TiO2-Cr2O3 and TiO2-Cr2O3 to increase the mechanical properties and resistance components of artificial joints on sliding abrasion and corrosion. This paper analyzes the influence of the plasma gun distance from the substrate on the mechanical properties and the microstructure of Cr2O3 layers deposited with the current of 40kW. The aim was to deposit layers with optimal characteristics that will enable the effective implementation of Cr2O3 layers on substrates of steel implants exposed to dry friction without lubrication and to corrosion of living tissues. The mechanical properties were tested by examining microhardness layers using the HV0.3 method and the strength was tested by tensile testing. The surface of powder particles was examined by SEM. The microstructures of layers were analyzed with the use of an optical microscope (OM) and a scanning electron microscope (SEM). The test results confirmed a possibility of effective application of bio-inert layers of Cr2O3 with other ceramics intended for the production of functional implants. / Метод плазменного напыления керамических Cr2O3 покрытий применяется как самостоятельное покрытие, так и в качестве дополнения к биоактивной органической композиционной керамике Ca10(PO4)6(OH)2-Al2O3-ZrO2-Cr2O3 и к иным биоинертным керамикам, создавая композиты типа Al2O3–ZrO2–SrO–Cr2O3– Y2O3, ZrO2-TiO2-Cr2O3 и TiO2-Cr2O3 с целью улучшения механических характеристик и повышения стойкости к износу и коррозии компонентов протеза сустава. В данной статье представлено каким образом расстояние между пистолетом для плазменного напыления и обрабатываемой поверхностью влияет на механические характеристики и микроструктуру Cr2O3 слоев покрытия, нанесенных при электоромощности 40 кВт. Цель нанесения различных слоев заключалась в определении лучших характеристик, которые обеспечат эффективное применение покрытия Cr2O3 для подложек металлических имплантатов, подверженных сухому трению без смазки, а также коррозии живых тканей. Анализ механических характеристик покрытия проведен на основании испытаний микротвердости методом HV0.3 и прочности соединений методом растяжения. Структура слоев испытана методом оптической микроскопии (ОМ), а поверхность испытана методом электронной микрографии (SEM). На основании полученных характеристик установлено, что эффективное применение биоинертных слоев Cr2O3 возможно и в сочетании с другими керамическими покрытиями, предназначенными для изготовления функциональных имплантатов. / Plazma sprej keramički slojevi Cr2O3 koriste se kao zasebna prevlaka ili kao dodatak bioreaktivnoj organskoj kompozitnoj keramici Ca10(PO4)6(OH)2-Al2O3-ZrO2-Cr2O3 i drugim bioinertnim keramikama, praveći kompozi tipa Al2O3-ZrO2-SrO-Cr2O3-Y2O3, ZrO2-TiO2-Cr2O3 i TiO2-Cr2O3 za povećanje mehaničkih karakteristika i otpornosti komponenti veštačkog zgloba na habanje klizanjem i koroziju. U radu je analiziran uticaj odstojanja plazma pištolja od podloge na mehaničke karakteristike i mikrostrukturu Cr2O3 slojeva deponovanih sa snagom napajanja od 40 kW. Cilj rada bio je da se deponuju slojevi optimalnih karakteristika koji će omogućiti efikasnu primenu Cr2O3 slojeva na podlogama čeličnih implantata izloženih suvom trenju bez podmazivanja i koroziji živih tkiva. Ispitivanje mehaničkih karakteristika realizovano je ispitivanjem mikrotvrdoće slojeva metodom HV0.3 i čvrstoće spoja metodom na zatezanje. Izgled površine čestica praha ispitan je metodom SEM. Mikrostrukture slojeva analizirane su uz primenu optičkog mikroskopa (OM) i skening elektronskog mikroskopa (SEM). Rezultati ispitivanja potvrdili su mogućnost efikasne primene bioinertnih slojeva Cr2O3 sa drugim keramikama namenjenim za izradu funkcionalnih implantata.
In this work, the main aim was to determine the effect of Mg addition on the crystallization kinetics and microstructure of Zn-10Al-1Cu alloy. The effectiveness of magnesium addition was detected on ...the basis of microstructure morphology investigations and changes occurring in the cooling curves of the investigated alloys. To describe the phenomena that occurred in the material during solidification under various conditions caused by a change in the chemical composition as a result of the appliance of modifiers, it was decided to use methods of thermal derivative analysis, allowing to effectively and accurately describe the crystallization kinetics of the tested materials. The scientific goal of the presented work was examination of the impact of magnesium addition and effect of the crystallization kinetics on the examined alloys. Determining the relationship between the changes in the derivative curve and the related microstructure, the influence of modifiers addition was analysed. The addition of Mg caused a shift of the solidification temperature values of phases and eutectics and monotectoid transformation (???) to lower temperature values, as well as the change of the morphology of the occurring eutectic ??+?.
W pracy opisano wpływ obróbki cieplnej na rozwój pęknięć zmęczeniowych w próbkach stal-tytan wykonanych metodą zgrzewania wybuchowego. Badane próbki o przekroju poprzecznym prostokątnym poddano ...zginaniu przy wartości średniej naprężenia równej zero. Dokonano pomiaru twardości w obszarze złącza. Wzrost pęknięć zmęczeniowych był cyklicznie mierzony przy użyciu mikroskopu optycznego. W próbkach obserwowano wzrost pęknięć zmęczeniowych równolegle do przyłożonego obciążenia, którego kierunek zmieniał się na linii złącza bimetalu. następnie obserwowano rozwój pęknięcia wzdłuż linii złącza powodując rozwarstwienie bimetalu. Rozwój pęknięć następował od strony stali lub tytanu w zależności od zastosowanej obróbki cieplnej (wielkość ziarna). Na przełomach bimetalu występują zarówno pęknięcia przebiegające transkrystaliczne jak i po granicy ziaren. Abstract The paper presents influence of heat treatment on the fatigue crack growth in steel-titanium specimens made by the explosive welding. The tested specimens of the rectangular cross-section were subjected to bending under the stress mean value equal to zero. The measurement of hardness was performed in the joint area. The fatigue crack growth was measured in cycles by means of the optical microscope. In the specimens, the fatigue crack growth was observed in parallel to the applied loading, the direction of which varied along the interface line. next, the crack growth was observed along the interface line when the bimetal was stratified. The crack growth started from the side of steel or titanium depending on the heat treatment (grain size). At the bimetal fractures there were both the cracks running transcrystalline and along the grain boundary ones as well.