At the end of the nineteenth and early twentieth century, in western part of Romania important buildings of reinforced concrete were built such as: water towers, bridges, industrial buildings. There ...are some buildings that used only reinforced concrete elements such as slabs, beams, walls and framing. Currently, these elements have low bearing capacity, putting at risk the security of buildings and their historical value. The main reasons are: low grade concrete, reinforcements without ductility that are highly damaged, low percentages of reinforcement. Different types of reinforcements do not provide the necessary ductility for buildings located in the seismic zone Banat, Romania. The article presents the state of degradation of these constructions and different ways to strengthen these historic buildings with reinforced concrete.
Design, description and experience with 45 years old cable-stayed SNP Bridge over the river Danube in Bratislava, Slovak Republic. Imperfection measurements, inspections, calculation of rating ...factors and evaluation of load-carrying capacities, proposal for exception, strengthening and its influence. Local and global buckling combined with shear lag effects. Influence of torsion at box girders. Development of cable-stayed bridges and position of the SNP Bridge in the world rankings of the large span cable-stayed bridges after 45 years from it opening.
The recommendations presented in this publication are inspired by the State of the Art Report edited by the RILEM Technical Committee TC 193 RLS
Bonded cement
-
based material overlays for the ...repair, the lining or the strengthening of slabs and pavements.
The objective is to lay out all the practical aspects to be considered in the design of concrete overlays: bonded concrete overlay process, assessment of the existing structure, surface preparation, overlay materials, design methods, construction procedure and quality control/assurance system, and maintenance.
Ce travail concerne l’étude du renforcement de structures en pierres par matériaux composites. Deux techniques de renforcement sont utilisées. L’un s’agit de renforcement par matrice cimentaire ...renforcé avec de textile de fibre de verre TRC. L’autre est renforcement par barres de fibre de verre de FRP suivant la technique de NSM (near-surface mounted). La première phase consiste en la caractérisation des matériaux et l’analyse des comportements mécaniques en compression en cisaillement et en traction de petits éléments de maçonnerie composées d’un assemblage de pierre et mortier bâtard. Les valeurs caractéristiques du comportement mécanique de la maçonnerie sont comparées avec les différents modèles dans la littérature qui calculent les paramètres caractéristiques avec une bonne approximation avec les résultats expérimentales. En plus, le comportement de matériaux de renforcement sont testés en traction ainsi que le comportement de l’adhésion entre le renfort et la maçonnerie est étudié. La deuxième phase se concentre sur le renforcement de murs de maçonnerie soumis sur deux types de chargement. L’un s’agit de cisaillement dans le plan des murs effectué avec l’essai de compression diagonale. Le deuxième représente des charges de flexion à 3 points hors plan des murs accompagné par des forces de compression axiale qui provoque une contrainte de compression de 0.2 MPa. L’essai de cisaillement s’est réalisé sur des murs carrés de cinq rangées de pierres avec mortier. Le renforcement par deux barres verticales de NSM FRP améliore significativement la ductilité et le module de cisaillement des murs, ainsi que le renforcement avec deux couches orthogonales de TRC améliore la résistance au cisaillement. Enfin l’application de modèles analytiques a permet de comparer les résultats expérimentaux aux résultats donnés avec les modèles. En plus, l’essai de flexion à 3 points est effectué sur des murs composés de douze rangées de pierres avec mortier. Le renforcement avec deux barres verticales et deux barres transversales a plus augmenté la rigidité élastique. En revanche, le renforcement avec TRC composé d’une seule couche de textile accompagné avec une barre verticale de FRP n’augmente pas la résistance de mur par rapport à la résistance du mur renforcé avec une seule couche de textile ou avec une barre verticale seule
This work concerns the study of the reinforcement of stone structures with composite materials. Two reinforcing techniques are used. One is reinforcement by cement matrix reinforced with textile TRC of glass fiber. The other is by reinforcing FRP fiberglass rods according to NSM technique (near-surface mounted). The first phase consists of materials characterization and analysis of mechanical behavior in compression shear and tensile of small masonry specimens made of stone and mortar. The characteristic values of the mechanical behavior of the masonry are compared with the different models in the literature which calculate the characteristic parameters and give a good approximation with the experimental results. In addition, the behavior of reinforced materials is tested in tension and the behavior of the adhesion between the reinforcement and the masonry is studied. The second phase focuses on strengthening masonry walls subjected to two types of loading. One is in-plane shear of walls made with the diagonal compression test. Represents the second bending loads to 3 points out of plane walls accompanied by axial compression forces which cause a compressive stress of 0.2 MPa. The shear test was performed on square walls of five rows of stones with mortar. Strengthening by two vertical bars NSM FRP significantly improves the ductility and shear modulus of the walls and the reinforcement with two orthogonal layers TRC improves shear strength. Finally the application of analytical models used to compare the experimental results with the results given by the models. In addition, the bending test with 3-point is carried out on walls composed of twelve rows of stones with mortar. The reinforcement with two vertical bars and two crossbars increased more elastic stiffness. However, the reinforcement with TRC composed of a single layer of textile accompanied with a vertical bar FRP does not increase the resistance of the wall relative to the resistance of the reinforced wall with a single layer of textile or with a simple vertical bar
Betonarme yapıların onarım ve güçlendirilmesinde (O/G) Lifli Polimer (FRP) malzemenin kullanımı son zamanlarda yaygınlaşmaya başlanmıştır. FRP malzemelerin, yüksek çekme mukavemeti, korozyona karşı ...dayanıklılığı ve bu malzeme ile yapılan O/G'nin, yapının işleyişini çok fazla etkilememesi gibi nedenlerle tercih edilen bir malzeme olmaktadır. Pamukkale Üniversitesi, Mühendislik Fakültesi, İnşaat Mühendisliği Bölümü, Yapı labaratuarlarında yapılan bu çalışmada dört adet betonarme kirişin FRP malzemelerle onarım ve/veya güçlendirilmesi yapılmıştır. Her deney kirişi için yük deplasman eğrisi elde edilerek elemanların statik yük altında O/G'den önceki ve sonraki davranışı karşılaştırılmıştır. Bu çalışma sonucunda FRP malzemelerle yapılan O/G'nin betonarme kirişlerin taşıma gücünü çok büyük ölçüde arttırdığı görülmüştür.
Betonarme yapıların onarım ve güçlendirilmesinde (O/G) Lifli Polimer (FRP) malzemenin kullanımı son zamanlarda yaygınlaşmaya başlanmıştır. FRP malzemelerin, yüksek çekme mukavemeti, korozyona karşı ...dayanıklılığı ve bu malzeme ile yapılan O/G'nin, yapının işleyişini çok fazla etkilememesi gibi nedenlerle tercih edilen bir malzeme olmaktadır. Pamukkale Üniversitesi, Mühendislik Fakültesi, İnşaat Mühendisliği Bölümü, Yapı labaratuarlarında yapılan bu çalışmada dört adet betonarme kirişin FRP malzemelerle onarım ve/veya güçlendirilmesi yapılmıştır. Her deney kirişi için yük deplasman eğrisi elde edilerek elemanların statik yük altında O/G'den önceki ve sonraki davranışı karşılaştırılmıştır. Bu çalışma sonucunda FRP malzemelerle yapılan O/G'nin betonarme kirişlerin taşıma gücünü çok büyük ölçüde arttırdığı görülmüştür.
Betonarme yapıların onarım ve güçlendirilmesinde (O/G) Lifli Polimer (FRP) malzemenin kullanımı son zamanlarda yaygınlaşmaya başlanmıştır. FRP malzemelerin, yüksek çekme mukavemeti, korozyona karşı ...dayanıklılığı ve bu malzeme ile yapılan O/G'nin, yapının işleyişini çok fazla etkilememesi gibi nedenlerle tercih edilen bir malzeme olmaktadır. Pamukkale Üniversitesi, Mühendislik Fakültesi, İnşaat Mühendisliği Bölümü, Yapı labaratuarlarında yapılan bu çalışmada dört adet betonarme kirişin FRP malzemelerle onarım ve/veya güçlendirilmesi yapılmıştır. Her deney kirişi için yük deplasman eğrisi elde edilerek elemanların statik yük altında O/G'den önceki ve sonraki davranışı karşılaştırılmıştır. Bu çalışma sonucunda FRP malzemelerle yapılan O/G'nin betonarme kirişlerin taşıma gücünü çok büyük ölçüde arttırdığı görülmüştür.
Electro stimulation as a physiotherapy technique is used as an analgesic and muscular strengthening so in pre-post surgery as in sportsmen or sportswomen, complementing other treatment techniques or ...physical training. Diverse electro stimulators promise encouraging results, besides that, do not describe their parameter. The purpose is to assess the efficiency of the combination of electro stimulation with physical exercise to increase the quadriceps quick strength, emphasizing its parameters and electrode collocation. It concluded in December 2008. Method: 6 healthy sportsmen (18-20 years) measured with a pre-post test en vertical jump, longitudinal and plyometric, so as a measure in time of quadriceps bank. Results: Electro stimulation combined with physical exercise increases the quick strength of quadriceps, but in high proportion to non trained individuals.
La electroestimulación como técnica de fisioterapia, es utilizada como analgésico y fortalecimiento muscular tanto en personas pre-post cirugía así como en deportistas, complementando otras técnicas de tratamiento o de entrenamiento físico. Diversos electroestimuladores prometen alentadores resultados, además, no describen sus parámetros. El propósito es valorar la eficacia de la combinación de electroestimulación con ejercicios físicos para aumentar la fuerza rápida del cuádriceps, haciendo énfasis en sus parámetros y colocación de electrodos. Concluyó en diciembre del 2008. Método: 6 sujetos deportistas sanos (18-20 años) con medición pre-post test en salto vertical, longitudinal y pliométrico, así como medición del tiempo en banco de cuadríceps. Resultados: La electroestimulación combinada con ejercicios físicos aumenta la fuerza rápida del cuadríceps, pero en mayor proporción en sujetos menos entrenados.
Betonarme yapıların onarım ve güçlendirilmesinde (O/G) Lifli Polimer (FRP) malzemenin kullanımı son zamanlarda yaygınlaşmaya başlanmıştır. FRP malzemelerin, yüksek çekme mukavemeti, korozyona karşı ...dayanıklılığı ve bu malzeme ile yapılan O/G’nin, yapının işleyişini çok fazla etkilememesi gibi nedenlerle tercih edilen bir malzeme olmaktadır. Pamukkale Üniversitesi, Mühendislik Fakültesi, İnşaat Mühendisliği Bölümü, Yapı labaratuarlarında yapılan bu çalışmada dört adet betonarme kirişin FRP malzemelerle onarım ve/veya güçlendirilmesi yapılmıştır. Her deney kirişi için yük deplasman eğrisi elde edilerek elemanların statik yük altında O/G’den önceki ve sonraki davranışı karşılaştınlmıştır. Bu çalışma sonucunda FRP malzemelerle yapılan O/G’nin betonarme kirişlerin taşıma gücünü çok büyük ölçüde arttırdığı görülmüştür.