With the aim of decreasing the number of experiments to obtain a perovskite solar cell (PSC) with maximum theoretical efficiency, in this paper, PSC performance was studied using the program solar ...cell capacitance simulator (SCAPS-1D). The PSC with the architecture ITO/TiO2/perovskite/spiro-MeOTAD/Au was investigated, while the selected perovskite was mixed cation Rb0.05Cs0.1FA0.85PbI3. The analysis was based on an experimentally prepared solar cell with a power conversion efficiency of ~7%. The PSC performance, verified by short-circuit current density (Jsc), open-circuit voltage (Voc), fill factor (FF) and power conversion efficiency (PCE), was studied by optimization of the simulation parameters responsible for improvement of the cell operation. The optimized parameters were absorber layer thickness, doping, defect concentration and the influence of the resistivity (the net effect of ohmic loss, Rs and the leakage current loss represented by the resistivity, Rshunt). The results of SCAPS-1D simulations estimated the theoretical power conversion efficiency of 15% for our material. We have showed that the main contribution to improvement of solar cell efficiency comes with lowering ohmic resistivity of the cell as well as doping and defect concentration, because their concentration is proportional to recombination rate.
Display omitted
The development of lipid nanoparticles requires knowledge on the crystalline structure, polymorphic transitions and lipid-drug interactions. This study aimed at introducing advanced ...techniques to characterize nanostructured lipid carriers (NLC) comprising palmitic acid, oleic acid, stabilizer and Domperidone. Crystallinity of single components and mixtures was investigated by laboratory Small Angle X-ray Scattering (SAXS). NLC were studied with laboratory Small and Wide Angle X-ray Scattering (SWAXS). Photon Correlation Spectroscopy and Freeze Fracture Transmission Electron Microscopy were used to monitor particle size, zeta potential and shape. Stability of NLC was investigated using synchrotron X-ray Diffraction (XRD) and SAXS and laboratory SAXS. Palmitic acid showed a lamellar structure (polymorph C), which was still present after particle preparation. Spherical 300 nm-sized particles with zeta potential values above −30 mV were obtained and Domperidone was incorporated in its amorphous form. During storage, no differences in synchrotron XRD spectra were seen. However, laboratory SAXS measurements showed a second lamellar structure, identified as polymorph B. Synchrotron SAXS temperature scans confirmed that polymorph B did not affect the morphology of the encapsulated drug or the shape of NLC. These results highlight the unique capabilities of laboratory and synchrotron X-ray Scattering and Diffraction for improved structural characterization of lipid nanoparticles.
Fluorine-doped tin oxide thin films (SnO2:F) are widely used as transparent conductive oxide electrodes in thin-film solar cells because of their appropriate electrical and optical properties. The ...surface morphology of these films influences their optical properties and therefore plays an important role in the overall efficiencies of the solar cells in which they are implemented. At rough surfaces light is diffusely scattered, extending the optical path of light inside the active layer of the solar cell, which in term improves light absorption and solar cell conversion efficiency. In this work, we investigated the surface morphology of undoped and doped SnO2 thin films and their influence on the optical properties of the films. We have compared and analysed the results obtained by several complementary methods for thin-film surface morphology investigation: atomic force microscopy (AFM), transmission electron microscopy (TEM), and grazing-incidence small-angle X-ray scattering (GISAXS). Based on the AFM and TEM results we propose a theoretical model that reproduces well the GISAXS scattering patterns.
Since the addition of BaTiO3 in perovskite solar cells (PSCs) provides a more energetically favorable transport route for electrons, resulting in more efficient charge separation and electron ...extraction, in this work we experimentally prepared such a PSC and used a modeling approach to point out which simulation parameters have an influence on PSC characteristics and how they can be improved. We added a layer of BaTiO3 onto the TiO2 electron transport layer and prepared a PSC, which had an FTO/TiO2/BaTiO3/FAPbI3/spiro-OMeTAD/Au architecture with a power conversion efficiency (PCE) of 11%. Further, we used the simulation program SCAPS-1D to investigate and optimize the device parameters (thickness of the BaTiO3 and absorber layers, doping, and defect concentration) resulting in devices with PCEs reaching up to 15%, and even up to 20% if we assume an ideal structure with no interlayer defects. Our experimental findings and simulations in this paper highlight the promising interplay of multilayer TiO2/BaTiO3 ETLs for potential future applications in PSCs.
SrMnO3 thin films were successfully prepared by spin coating the viscous solution obtained from the autocombustion synthesis. To ensure the transformation of the precursor solution into the manganite ...phase, conventional thermal treatment and novel phototreatment were applied. The thermal treatment resulted in stable hexagonal SrMnO3, while phototreatment yielded cubic SrMnO3 phase which is usually not stable at ambient conditions. The optical properties of the prepared materials were measured revealing the optical gaps of 1.5 eV for thermally treated material and about 1.3 – 1.4 eV for the phototreated samples. Comparison with ab initio result shows a higher theoretical value of 1.9 eV, ascribed to high exciton binding energy. Since these values are similar to the optical gap (1.48 eV) of widely studied formamidium lead iodide thin films, SrMnO3 thin films are promising candidates for active layers in inorganic perovskite solar cells.
•SrMnO3 thin films were successfully prepared by citric route.•A novel IPL phototreatment technique was applied for film deposition.•IPL phototreatment yielded cubic SrMnO3 phase.•Measured optical gaps are in a 1.3 – 1.5 eV range.•SrMnO3 films are promising active layers in perovskite solar cells.
A series of semi-transparent W-incorporated TiO2 thin films (TxW; x = 0,1,2,5, and 10) were fabricated by anodizing co-sputtered titanium-tungsten (WiTi1−i (0 ≤ i ≤ 0.05)). Field emission gun ...scanning electron microscopy, energy dispersive X-ray spectroscopy, X-ray photoelectron spectroscopy, Grazing incidence X-ray diffraction, and Raman spectroscopy were used to characterize TxW thin films, which confirmed the anatase form of TiO2 as well as the presence of W in the thin films. Optoelectronic and photoelectrochemical characterization showed that TxW thin films are markedly beneficial for reducing photo generated charges recombination. T1W exhibited the maximum charge carrier lifetime (0.29 µs) which is over two times of pristine T0W (0.13 µs). Methylene blue (MB) and imidacloprid (IMI) were selected as the target pollutants for the study of photocatalytic effectiveness of TxW under solar light. T1W showed maximum removal efficiency for MB at pH8. Moreover, response surface methodology analyses revealed that IMI removal efficiency enhanced about three times at pH 4 with adding 255 µM of H2O2.
Display omitted
•Fabrication of semi-transparent TxW thin films by anodizing co-sputtered WiT1−i films.•Enhancement charge carrier life time through W incorporation into TiO2 structure.•Photocatalytic activity association of with the ratio of W in TxW thin films.•Improvement MB removal efficiency with increasing pH.•IMI removal efficiency optimization using response surface methodology.
In this paper, we studied the influence of polyvinylpyrrolidone (PVP) as a stabilization additive on optical and electrical properties of perovskite formamidinium lead iodide (FAPI) polycrystalline ...thin films on ZnO nanorods (ZNR). FAPI (as an active layer) was deposited from a single solution on ZNR (low temperature processed electron transport layer) using a one-step method with the inclusion of an anti-solvent. The role of PVP in the formation of the active layer was investigated by scanning electron microscopy and contact angle measurements to observe the effect on morphology, while X-ray diffraction was used as a method to study the stability of the film in an ambient environment. The effect of the PVP additive on the optical and electrical properties of the perovskite thin films was studied via photoluminescence, UV-Vis measurements, and electrical impedance spectroscopy. We have demonstrated that PVP inclusion in solution-processed perovskite FAPI thin films prevents the degradation of the film in an ambient atmosphere after aging for 2 months. The inclusion of the PVP also improves the infiltration of FAPI perovskite into ZnO nanostructures, increases electrical conductivity and radiative recombination of the photo-generated charge carriers. These results show promising information for promoting PVP stabilized FAPI perovskites for the new generation of photovoltaic devices.
ZnO has prominent electron transport and optical properties, beneficial for photovoltaic application, but its surface is prone to the formation of defects. To overcome this problem, we deposited ...nanostructured TiO2 thin film on ZnO nanorods to form a stable shell. ZnO nanorods synthesized by wet-chemistry are single crystals. Three different procedures for deposition of TiO2 were applied. The influence of preparation methods and parameters on the structure, morphology, electrical and optical properties were studied. Nanostructured TiO2 shells show different morphologies dependent on deposition methods: (1) separated nanoparticles (by pulsed laser deposition (PLD) in Ar), (2) a layer with nonhomogeneous thickness (by PLD in vacuum or DC reactive magnetron sputtering), and (3) a homogenous thin layer along the nanorods (by chemical deposition). Based on the structural study, we chose the preparation parameters to obtain an anatase structure of the TiO2 shell. Impedance spectroscopy shows pure electron conductivity that was considerably better in all the ZnO@TiO2 than in bare ZnO nanorods or TiO2 layers. The best conductivity among the studied samples and the lowest activation energy was observed for the sample with a chemically deposited TiO2 shell. Higher transparency in the visible part of spectrum was achieved for the sample with a homogenous TiO2 layer along the nanorods, then in the samples with a layer of varying thickness.
Transparent conducting oxides (TCO) with high electrical conductivity and at the same time high transparency in the visible spectrum are an important class of materials widely used in many devices ...requiring a transparent contact such as light-emitting diodes, solar cells and display screens. Since the improvement of electrical conductivity usually leads to degradation of optical transparency, a fine-tuning sample preparation process and a better understanding of the correlation between structural and transport properties is necessary for optimizing the properties of TCO for use in such devices. Here we report a structural and magnetotransport study of tin oxide (SnO2), a well-known and commonly used TCO, prepared by a simple and relatively cheap Atmospheric Pressure Chemical Vapour Deposition (APCVD) method in the form of thin films deposited on soda-lime glass substrates. The thin films were deposited at two different temperatures (which were previously found to be close to optimum for our setup), 590 °C and 610 °C, and with (doped) or without (undoped) the addition of fluorine dopants. Scanning Electron Microscopy (SEM) and Grazing Incidence X-ray Diffraction (GIXRD) revealed the presence of inhomogeneity in the samples, on a bigger scale in form of grains (80–200 nm), and on a smaller scale in form of crystallites (10–25 nm). Charge carrier density and mobility extracted from DC resistivity and Hall effect measurements were in the ranges 1–3 × 1020 cm−3 and 10–20 cm2/Vs, which are typical values for SnO2 films, and show a negligible temperature dependence from room temperature down to −269 °C. Such behaviour is ascribed to grain boundary scattering, with the interior of the grains degenerately doped (i.e., the Fermi level is situated well above the conduction band minimum) and with negligible electrostatic barriers at the grain boundaries (due to high dopant concentration). The observed difference for factor 2 in mobility among the thin-film SnO2 samples most likely arises due to the difference in the preferred orientation of crystallites (texture coefficient).
The aim of this study was to examine the effect of positively charged (amine-modified) and negatively charged (carboxyl-modified) polystyrene nanoplastics (PS NPs) on the nanostructural, ...nanomechanical, and antioxidant responses of the marine diatom Cylindrotheca closterium. The results showed that both types of PS NPs, regardless of surface charge, significantly inhibited the growth of C. closterium during short-term exposure (3 and 4 days). However, longer exposure (14 days) to both PS NPs types did not significantly inhibit growth, which might be related to the detoxifying effect of the microalgal extracellular polymers (EPS) and the higher cell abundance per PS NPs concentration. The exposure of C. closterium to both types of PS NPs at concentrations above the corresponding concentrations that resulted in a 50% reduction of growth (EC50) demonstrated phytotoxic effects, mainly due to the excessive production of reactive oxygen species, resulting in increased oxidative damage to lipids and changes to antioxidant enzyme activities. Diatoms exposed to nanoplastics also showed a significant decrease in cell wall rigidity, which could make the cells more vulnerable. Atomic force microscopy images showed that positively charged PS NPs were mainly adsorbed on the cell surface, while both types of PS NPs were incorporated into the EPS that serves to protect the cells. Since microalgal EPS are an important food source for phytoplankton grazers and higher trophic levels, the incorporation of NPs into the EPS and interactions with the cell walls themselves may pose a major threat to marine microalgae and higher trophic levels and, consequently, to the health and stability of the marine ecosystem.
PDF
