The objective of this study was to evaluate the fracture load and retention force of different bonding systems while restoring one-piece zirconia implants with a novel cementation approach using a ...mesostructure. Polymer-infiltrated ceramic mesostructures (n = 112) were therefore designed as caps on the implant abutment, and a molar feldspathic ceramic crown was constructed on top of it as a suprastructure. For cementation, different bonding systems were used. Fracture load and retention force were measured immediately after storage in water at 37 °C for 24 h (n = 8) as well as after artificial aging in a chewing simulator and subsequent thermal cycling (n = 8). Combined restorations showed higher fracture load compared to monolithic restorations of polymer-infiltrated ceramic (n = 8) or feldspathic ceramic (n = 8) identical in shape. However, the fracture load of the combined restorations was significantly affected by aging, independent of the primers and cements used. Restorations cemented with primers containing methyl methacrylate and 10-methacryloyloxydecyl dihydrogen phosphate exhibited the highest retention force values. Aging did not affect the retention force significantly. Similar fracture load values can be expected from combination restorations when compared with monolithic crowns.
The most common three-dimensional (3D) printing method is material extrusion, where a pre-made filament is deposited layer-by-layer. In recent years, low-cost polycaprolactone (PCL) material has ...increasingly been used in 3D printing, exhibiting a sufficiently high quality for consideration in cranio-maxillofacial reconstructions. To increase osteoconductivity, prefabricated filaments for bone repair based on PCL can be supplemented with hydroxyapatite (HA). However, few reports on PCL/HA composite filaments for material extrusion applications have been documented. In this study, solvent-free fabrication for PCL/HA composite filaments (HA 0%, 5%, 10%, 15%, 20%, and 25% weight/weight PCL) was addressed, and parameters for scaffold fabrication in a desktop 3D printer were confirmed. Filaments and scaffold fabrication temperatures rose with increased HA content. The pore size and porosity of the six groups' scaffolds were similar to each other, and all had highly interconnected structures. Six groups' scaffolds were evaluated by measuring the compressive strength, elastic modulus, water contact angle, and morphology. A higher amount of HA increased surface roughness and hydrophilicity compared to PCL scaffolds. The increase in HA content improved the compressive strength and elastic modulus. The obtained data provide the basis for the biological evaluation and future clinical applications of PCL/HA material.
Zirconia implants that were restored with veneered zirconia displayed severe chipping rates of the restorations in clinical studies. Purpose of this study was to evaluate the fracture load of ...different zirconia implant supported monolithic crown materials (zirconia, alumina, lithium disilicate, feldspar ceramic and polymer-infiltrated ceramic) cemented with various cements (Harvard LuteCem SE, Harvard Implant Semi-permanent, Multilink Automix, VITA Adiva F-Cem). Flexural strength and fracture toughness of crown materials and compressive strength of the cements were measured. Fracture load values of crowns fabricated from lithium disilicate, feldspar ceramic and polymer-infiltrated ceramic were increased when cement with high compressive strength was used. Fracture loads for zirconia and alumina crowns were not influenced by the cement. Flexural strength and fracture toughness of the ceramics correlated linearly with the respective fracture load when using adhesive cement with high compressive strength. To achieve sufficient fracture load values, cementation with adhesive cement is essential for feldspar and polymer-infiltrated ceramic.
Objective
The purpose of this study is to compare the bonding performance and mechanical properties of two different resin composite cements using simplified adhesive bonding strategies.
Materials ...and methods
Shear bond strength of two resin composite cements (an adhesive cement: Panavia V5 PV5 and a self‐adhesive cement: RelyX Universal RUV) to human enamel, dentin, and a variety of restorative materials (microfilled composite, composite, polymer‐infiltrated ceramic, feldspar ceramic, lithium disilicate and zirconia) was measured. Thermocycle aging was performed with selected material combinations.
Results
For both cements, the highest shear bond strength to dentin was achieved when using a primer (PV5: 18.0 ± 4.2 MPa, RUV: 18.2 ± 3.3 MPa). Additional etching of dentin reduced bond strength for RUV (12.5 ± 4.9 MPa). On enamel, PV5 achieved the highest bond strength when the primer was used (18.0 ± 3.1 MPa), while for RUV etching of enamel and priming provided best results (21.2 ± 6.6 MPa). Shear bond strength of RUV to restorative materials was superior to PV5. Bonding to resin‐based materials was predominantly observed for RUV.
Conclusions
While use of RUV with the selective‐etch technique is slightly more labor intensive than PV5, RUV (with its universal primer) displayed a high‐bonding potential to all tested restorative materials, especially to resin.
Clinical significance
For a strong adhesion to the tooth substrate, PV5 (with its tooth primer) is to be preferred because etching with phosphoric acid is not required. However, when using a wide range of varying restorative materials, RUV with its universal primer seems to be an adequate option.
Abstract Statement of problem The best procedure for cementing a restoration to zirconia implants has not yet been established. Purpose The purpose of this in vitro study was to measure the retention ...of polymer-infiltrated ceramic crowns to zirconia 1-piece implants using a wide range of cements. The effect of ceramic primer treatment on the retention force was also recorded. The retention results were correlated with the shear bond strength of the cement to zirconia and the indirect tensile strength of the cements to better understand the retention mechanism. Material and methods The retention test was performed using 100 polymer-infiltrated ceramic crowns (Vita Enamic) and zirconia implants (ceramic.implant CI) The crowns were cemented with either temporary cement (Harvard Implant semipermanent, Temp Bond), glass-ionomer cement (Ketac Cem), self-adhesive cement (Perma Cem 2.0, RelyX Unicem Automix 2, Panavia SA), or adhesive cement (Multilink Implant, Multilink Automix, Vita Adiva F-Cem, RelyX Ultimate, Panavia F 2.0, Panavia V5 or Panavia 21) (n=5). Additionally ceramic primer was applied on the intaglio crown surface and implant abutment before cementation for all adhesive cements (Multilink Implant, Multilink Automix: Monobond plus; RelyX Ultimate Scotchbond Universal; Vita Adiva F-Cem: Vita Adiva Zr-Prime; Panavia F2.0, Panavia V5: Clearfil Ceramic Primer) and 1 self-adhesive cement containing 10-methacryloyloxydecyl dihydrogen phosphate (MDP) (Panavia SA: Clearfil Ceramic Primer). Crown debond fracture patterns were recorded. Shear bond strength was determined for the respective cement groups to polished zirconia (n=6). The diametral tensile strength of the cements was measured (n=10). Statistical analysis was performed using 1-way or 2-way analysis of variance followed by the Fisher LSD test (α=.05) within each test parameter. Results Adhesive and self-adhesive resin cements had shear bond strength values of 0.0 to 5.3 MPa and revealed similar retention forces. Cements containing MDP demonstrated shear bond strength values above 5.3 MPa and displayed increased retention. The highest retention values were recorded for Panavia F 2.0 (318 ±28 N) and Panavia 21 (605 ±82 N). All other adhesive and self-adhesive resin cements attained retention values between 222 ±16 N (Multilink Automix) and 270 ±26 N (Panavia SA), which were significantly higher ( P <.05) than glass-ionomer (Ketac Cem: 196 ±34 N) or temporary cement (Harvard Implant semipermanent: 43 ±6 N, Temp Bond: 127 ±13 N). Application of manufacturer-specific ceramic primer increased crown retention significantly only for Panavia SA. Conclusions Products containing MDP provided a high chemical bond to zirconia. Self-adhesive and adhesive resin cements with low chemical bonding capabilities to zirconia provided retention force values within a small range (220 to 290 N).
Objective
This study evaluated the loading capacity of CAD/CAM‐fabricated anterior feldspathic ceramic crowns bonded to one‐piece zirconia implants with different cements.
Material and methods
Fifty ...one‐piece zirconia implants were embedded in epoxy resin. The abutment aspect of one implant was optically scanned and a standardized upper canine was designed with CAD‐software. Fifty feldspathic ceramic crowns were milled, polished, and mounted on the implants either without any cement, with a temporary cement or with three different composite resin cements after surface pretreatment as recommended by the manufacturers (n = 10). After storage in distilled water at 37°C for 24 hr, specimens were loaded until fracture on the palatal surface of the crown at an angle of 45° to the long axis of the implant and loads until fracture were detected and compared. Compressive strength of the investigated cement materials was determined. Statistical analyses were done with One‐way ANOVA followed by post hoc Fisher LSD test (α = 0.05).
Results
The cements revealed significantly different compressive strength values (temporary cement: 37.1 ± 7.0 MPa; composite resin cements: 185.8 ± 21.3, 277.9 ± 22.1, and 389.0 ± 13.6 MPa, respectively). Load‐at‐fracture values had an overall mean value of 237.1 ± 58.2 N with no significant difference among the composite resin cements (p > 0.05). Fracture load values with the temporary cement or without cement were significantly lower (p < 0.002).
Conclusions
CAD/CAM‐fabricated anterior feldspathic ceramic crowns bonded to one‐piece zirconia implants provide sufficient resistance to intraoral forces.
Purpose To test if resin CAD/CAM materials should be considered for zirconia implants and how their mechanical properties affect the fracture load.Methods Fracture load of molar crowns of CAD/CAM ...materials (VITA CAD-Temp CT, Cerasmart CS, Lava Ultimate LU, Pekkton Ivory PK) on zirconia implants (ceramic.implant, 4.0 mm) fixed either with no cement, temporary cement (Harvard Implant semi-permanent HIS), self-adhesive (VITA Adiva S-Cem VAS) or either one of two adhesive cements (Multilink Automix MLA, VITA Adiva F-Cem VAF) was analyzed. The restorative materials were characterized by their flexural strength, fracture toughness, elemental composition and organic/inorganic ratio while compressive strength of the cements was measured.Results For the fracture load significantly highest mean values were found overall for PK (2921 ±300 N) > LU (2017 ±499 N) > CS (1463 ±367 N) = CT (1451 ±327 N) (p > 0.05). When analyzing the effect of the cement on the fracture load the overall ranking was VAF (2245 ±650 N) ≥ MLA (2188 ±708 N) ≥ VAS (2017 ±563 N) > HIS (1757 ±668 N) = no cement (1595 ±757 N) (p <0.05), meaning fracture load increased with the compressive strength of the cements. Additionally, a linear trend was found between the fracture load and the fracture toughness of the restorative materials.Conclusions All restorative materials exhibited fracture load values similar or higher than lithium disilicate tested previously. Fracture load of CT, CS and LU can be significantly increased when an adhesive cement with a high compressive strength is used.
Human gingival fibroblast (HGF-1) cells in the connective tissue provide an effective barrier between the alveolar bone and the oral environment. Cement margins of restorations with intrasulcular ...preparation or cemented implant restorations are in contact with HGF cells. However, it is unknown to what extend the cement surface finish affects the behavior of HGF cells. The purpose of this study was to compare the behavior of HGF-1 cells in contact with two different resin composite cements with three different surface treatments after light-curing and autopolymerization, respectively.
Disks of one adhesive (Multilink Automix, Ivoclar Vivadent MLA) and one self-adhesive (RelyX Unicem 2 Automix, 3 M RUN) resin composite cement were either light-cured or autopolymerized. Specimen surfaces were prepared with the oxygen inhibition layer intact, polished with P2500-grit silicon carbide paper or treated with a scaler. Cells were cultivated on the specimens for 24 h. Viability assay was performed, and cell morphology was examined with scanning electron microscopy. Additionally, roughness parameters of the specimen were analyzed with a 3D laser scanning microscope. Three-way ANOVA was applied to determine the effect of cement material, curing mode and surface treatment (a = 0.05).
Overall, cement material (p = 0.031), curing mode (p = 0.001), and surface treatment (p < 0.001) significantly affected relative cell viability of HGF. The autopolymerized specimen with the oxygen inhibition layer left intact displayed the lowest relative cell viability (MLA 25.7%, RUN 46.6%). Removal of the oxygen inhibition layer with a scaler increased cell viability but also resulted in higher surface roughness values.
HGF cell viability is affected by the surface treatment and the curing mode. The oxygen inhibition layer is an inhibitory factor for the viability of HGF cells. Autopolymerization enhances the cytotoxic potential of the oxygen inhibition layer.
To test three potential prosthetic material options for zirconia implants in regard to their mechanical properties, loading and retention capacity as well as to record abrasion after chewing ...simulation followed by thermocyclic aging.
Molar crowns (n = 96) of three different computer-aided design/computer-aided manufacturing (CAD/CAM) materials were produced and cemented on zirconia implants (ceramic.implant, Vita) with a diameter of 4.5 mm. Monolithic zirconia (Vita YZ YZ with RelyX Unicem 2 Automix RUN, polymer-infiltrated ceramic (Vita Enamic VE) with Vita Adiva F-Cem VAF and acrylate polymer (CAD Temp CT) with RelyX Ultimate RUL. Fracture load and retentive force of the crowns were measured after 24 h water storage at 37 °C and after a chewing simulation followed by thermocyclic aging. Abrasion was recorded by matching stereolithography-data of the crowns obtained before and after chewing simulation. Additionally, the mechanical properties and bonding capabilities of the crown and cement materials were assessed.
Fracture load values were significantly highest for YZ > VE = CT. Retention force values did not differ significantly between the materials. The aging procedure did not affect the fracture load values nor the retention force significantly. Abrasion depth of the crowns was lowest for YZ followed by VE and CT. On unpolished crowns, abrasion of YZ and VE tended to be higher than on polished specimens.
Based on the obtained in-vitro results, all tested materials can be recommended for the use on zirconia implants, although CT is only approved for temporary crowns. The loading and retention capacity of the materials were not significantly affected by aging.
Focusing on the basic structure as the subject of justice has tended to lead theorists to make a choice: either there is no global basic structure and therefore obligations of justice remain domestic ...only (the statist position) or there is sufficient institutional basis at the global level to warrant affirming a basic structure global in scope, meaning that duties of justice must also be global (the cosmopolitan position). Recent literature, however, has pointed out that this might be a false choice between denying and asserting the existence of a global basic structure. There are two main claims that I make in this paper. First, I claim that on a Rawlsian understanding of the basic structure, justice does not require one before its demands arise, but rather that under certain conditions, justice can require that a basic structure be established as an essential part of fulfilling its demands. This has the benefit of not restricting the scope of justice to the domestic sphere. Thus, the second claim is about determining, from a practice-dependent, non-ideal starting point, what those “certain conditions” are. Specifically, I argue that when currently existing global institutions begin impacting on the freedom of individuals to interact against a fair backdrop and pervasively impact on life chances, then the demands of justice will arise and we will need to establish a global basic structure. This paper, then, also has implications for the ideal/non-ideal theory debate, because I argue that the best way to globalize the basic structure is to begin from a non-ideal starting point.Article first published online: 9 NOV 2015
PDF
