The main aim of this article is to analyse the Si solar cell’s behaviour when it is exposed to light of different colours. An experimental work, with 100 experimental tests, was carried out, using an ...RGB LED. In order to obtain better fitting of the characteristic curves’ results, we used a novel discrete model, d1MxP. The obtained results showed that all experimental points of the tests were inside the two triangles that connected the three theoretical primary colours and the three experimental primary colours in the chromaticity diagram. With this diagram, the colour purity could be determined, which presented values between 20% and 60%. The primary colours of the three different LEDs of the light source presented a dominant wavelength that corresponded to the peak wavelengths of the light source spectrum, which showed high purity. However, the obtained results show that mixing colours may not lead to an increase in the cell’s output power. Additionally, an increase in the cell’s temperature was observed, due to the surplus absorbed energy, which was converted into heat, being one of the causes of the cell’s efficiency reduction.
Concentrating photovoltaic (CPV) systems have emerged as a transformative technology that incorporates radiation concentrators into the photovoltaic system to enable radiation to be concentrated onto ...a receiver—the solar cells. Different concentrator configurations have different impacts on the performance of the solar photovoltaic system. This research work aims to analyze the impact of different concentrators, comparing and identifying the most efficient structures for capturing and concentrating solar energy. Aiming at a deep analysis and comparison among concentrators shapes, this research work presents a unique investigation and revision among different structures such as flat, triangular, LFR, and parabolic concentrators. Moreover, since, in the UV–visible–NIR region, metals’ reflectance varies with the incident wavelength, five metals were considered: aluminum, gold, platinum, copper, and silver. Additionally, the research focuses on studying the effects of parameters critical to the quality of the concentration on the power obtained and on the uniformity of the radiation distribution on the surface of the receiver, as well as on the number of solar rays that reach the receiver. The power on the receiver increases proportionally with the number of reflector concentrators in the system and their reflectance. For parabolic geometries, the optical efficiency is affected by the receiver’s shadow on the concentrator and, in the case of the LFR, by a non-ideal alignment of the reflectors in relation to the receiver. However, in parabolic concentrator geometries, uniformity is usually lower, since in these configurations, the radiation is focused on specific areas of the receiver, usually the central zone.
Renewable resources for producing energy for self-consumption are growing, namely solar energy. This work focuses on the comparison of photovoltaic systems for energy production for self-consumption ...on a property in three different regions of Portugal using traditional and emerging technologies, without batteries’ implementation. According to Portuguese law, there is no stipulated value for selling surplus energy produced by a self consumption unit, to the public grid. In order to analyse the economic viability of the project, two scenarios are studied: the delivery, at zero cost of the surplus energy produced to the grid, and its sale. Furthermore, the same analysis is carried out considering partial shading on the photovoltaic generator. The results show that if there is no surplus production sale to the grid, the project becomes economically unviable for the four PV technologies. Otherwise, for the traditional technologies, the project is economically viable, presenting a payback time lower than 10 years. Using emerging technologies, the project becomes economically unviable. When applying partial shading on the generator, the project becomes, in all the scenarios under study, economically unviable. It can be concluded that introducing nanostructures in solar cells to power an infrastructure is not, for now, the best solution from an economic point of view, considering the current legislation. In addition, the shading makes the projects under study unviable, as it is a factor that cannot be controlled in its entirety.
The performance of photovoltaic solar cells is usually analyzed using continuous models, for instance, 1M5P. I-V and P-V curves are fitted by a mathematical expression from the electrical model. In ...the case of 1M5P, characteristics are fitted using five parameters that are obtained using a small number of I-V points from a wider set of data, keeping the curve shape given by the mathematical expression from the model. A novel model was recently proposed to overcome this issue. The d1MxP model is based on the discretization of the electrical behavior of the diodes in models such as 1M5P. The d1MxP methodology is equivalent to an analytical incremental calculation and since it connects the given points, the model error should be lower than the one obtained using models as 1M5P. It is based on the connection of adjacent points (with small voltage differences) instead of having the entire voltage range represented by some parameters (as the continuous models do, for instance, 1M5P). In this work, the d1MxP model is applied to perovskite solar cells and paint-type dye-sensitized solar cells. The aim is to analyze the behavior of the discrete model in different third-generation solar cells since their performance cannot be well characterized by the 1M5P model. The accuracy on the maximum power point is relevant, resulting in perovskite solar cells, an improvement of up to 2.61% and, in paint-type dye-sensitized solar cells, an increase of up to 5.03%.
This research work aims to study photovoltaic systems that generate energy for self-consumption using different traditional technologies, such as silicon, and emerging technologies, like nanowires ...and quantum. The photovoltaic system without batteries was implemented in a residential property in three different places, in Portugal. According to Portuguese Law, the sale of surplus energy to the grid is possible but the respective value for its selling is not defined. To evaluate the project viability, two different analyses are considered: with and without the sale of surplus energy to the grid. Results show that if there is no sale of excess energy produced to the grid, the project is not economically viable considering the four different technologies. Otherwise, using traditional technologies, the project is economically viable, presenting a payback time lower than 10 years. This shows that the introduction of nanostructures in solar cells is not yet a good solution in the application of solar systems namely with the current law. Furthermore, independently of the used technology, the current Portuguese law seems to difficult the investment return, which should not be the way to encourage the use of renewable sources.
