Narodna in univerzitetna knjižnica, Ljubljana (NUK)
-
Study of conventional mould design for gate location and cooling channelsDevos, S. ; Cardon, Ludwig ; Drstvenšek, IgorInjection moulding is a technique to shape melted plastic in the desired form. To become a good product there are a lot of parameters. In this paper we will discuss problems that can occur while ... manufacturing a product with injection moulding. One of the main problems we will discuss is the gate location of the product and the cooling of the mould. All these problems will be exanimate on a specific product. The product is the cover of an LPG tank of an car. It shows some design problems with the manufacturing cycle at the moment. Now some burned spots, warpage and flow lines are observed. When we examine the product it is noticed that the gate is positioned on a bad location. Actually, the gate location is located at a not symmetrical place. To avoid problems with the design it is suggested to put the location on a symmetrical position. To solve the burned spots and the warpage it is better to add some cooling. Once the calculated cooling is added and the correct gate location is chosen, we will do an analyse on the two different product. The results will show that with a good gate location and good cooling a lot of problems can be solved.Vir: Advances in production engineering & management. - ISSN 1854-6250 (Vol. 5, no. 4, dec. 2010, str. 235-244)Vrsta gradiva - članek, sestavni delLeto - 2010Jezik - angleškiCOBISS.SI-ID - 14673686
Avtor
Devos, S. |
Cardon, Ludwig |
Drstvenšek, Igor
Teme
injekcijsko brizganje |
hlajenje |
injection moulding |
gate location |
cooling |
simulation
![loading ... loading ...](themes/default/img/ajax-loading.gif)
vir: Advances in production engineering & management. - ISSN 1854-6250 (Vol. 5, no. 4, dec. 2010, str. 235-244)
![loading ... loading ...](themes/default/img/ajax-loading.gif)
![loading ... loading ...](themes/default/img/ajax-loading.gif)
![loading ... loading ...](themes/default/img/ajax-loading.gif)
Vnos na polico
Trajna povezava
- URL:
Faktor vpliva
Dostop do baze podatkov JCR je dovoljen samo uporabnikom iz Slovenije. Vaš trenutni IP-naslov ni na seznamu dovoljenih za dostop, zato je potrebna avtentikacija z ustreznim računom AAI.
Leto | Faktor vpliva | Izdaja | Kategorija | Razvrstitev | ||||
---|---|---|---|---|---|---|---|---|
JCR | SNIP | JCR | SNIP | JCR | SNIP | JCR | SNIP |
Baze podatkov, v katerih je revija indeksirana
Ime baze podatkov | Področje | Leto |
---|
Povezave do osebnih bibliografij avtorjev | Povezave do podatkov o raziskovalcih v sistemu SICRIS |
---|---|
Devos, S. | ![]() |
Cardon, Ludwig | ![]() |
Drstvenšek, Igor | 11943 |
Vir: Osebne bibliografije
in: SICRIS
Izberite prevzemno mesto:
Prevzem gradiva po pošti
Naslov za dostavo:
Med podatki člana manjka naslov.
Storitev za pridobivanje naslova trenutno ni dostopna, prosimo, poskusite še enkrat.
S klikom na gumb "V redu" boste potrdili zgoraj izbrano prevzemno mesto in dokončali postopek rezervacije.
S klikom na gumb "V redu" boste potrdili zgoraj izbrano prevzemno mesto in naslov za dostavo ter dokončali postopek rezervacije.
S klikom na gumb "V redu" boste potrdili zgoraj izbrani naslov za dostavo in dokončali postopek rezervacije.
Obvestilo
Trenutno je storitev za avtomatsko prijavo in rezervacijo nedostopna. Gradivo lahko rezervirate sami na portalu Biblos ali ponovno poskusite tukaj kasneje.
Gesla v Splošnem geslovniku COBISS
Izbira mesta prevzema
Gradivo iz matične enote je brezplačno. Če je gradivo na mesto prevzema dostavljeno iz drugih enot, lahko knjižnica to storitev zaračuna.
Mesto prevzema | Status gradiva | Rezervacija |
---|
Rezervacija v teku
Prosimo, počakajte trenutek.
Rezervacija je uspela.
Rezervacija ni uspela.
Rezervacija...
Članska izkaznica:
Mesto prevzema:
Naročanje gradiva za izposojo v čitalnice
Naročanje kopij člankov
Urnik dostave gradiva z oznako DS v signaturi