Dynamic three‐dimensional computed tomography (CT) imaging of liquid transport in porous media has primarily been conducted at high brilliance synchrotrons thus allowing fast, sometimes sub‐second, ...temporal resolution to be obtained. University laboratory CT instruments lack the photon flux available at synchrotrons, limiting the obtainable spatiotemporal resolution. Here, we discuss our experiences with instrumentation and software methods to conduct time‐resolved micro‐computed tomography (4D‐CT) experiments of flow in porous media, based on a conventional CT instrument operated with a highly undersampled number of projections. An experimental stage outfitted with syringe pumps placed on a slip ring allowed two‐phase flow experiments to be carried out with continuous unidirectional rotation and without obstruction of the liquid supply lines. An iterative reconstruction algorithm based on a priori information was used to provide high image quality and ∼30 s time resolution despite the few and low‐exposed projections compared to standard protocols. The experimental technique was demonstrated with imbibition and drainage in glass bead‐pack and Bentheimer sandstone samples with sub‐minute temporal resolution, allowing the liquid configurations just before and after fast dynamic phenomena such as cooperative pore‐filling events and Haines jumps to be captured. Power law scaling exponents for burst volumes associated with imbibition and drainage were estimated and compared with the literature. That 4D‐CT experiments can be carried out using conventional CT instruments to challenge contemporary permeability models is of high importance for many geo‐, bio‐ and environmental physics challenges.
Plain Language Summary
Computed Tomography or CT is well‐known as a technique for investigating objects in 3D non‐destructively. In principle, 3D movies, referred to as “dynamic CT” or “4D CT” is a simple extension, requiring just a series of standard CT experiments to be carried out in sequence. In practice, however, there is a high demand for clever methods and algorithms that can simultaneously obtain high spatial and temporal resolutions. When more than one fluid is being transported through a porous medium, a plethora of phenomena take place, and 4D‐CT has proven a powerful tool to better understand the physics of porous media. Most 4D‐CT studies in the past have been carried out at synchrotron facilities, which are extremely high flux X‐ray sources, but also a scarce and expensive resource. We describe our experiences with 4D‐CT measurements of fluid transport in porous media, as performed in our home laboratory.
Key Points
Time‐resolved 3D imaging of flow in porous media
Dynamic micro‐computed tomography
Semiconducting diblock copolymers of polyethylene (PE) and regioregular poly(3‐hexylthiophene) (P3HT) are demonstrated to exhibit a rich phase behaviour, judicious use of which permitted us to ...fabricate field‐effect transistors that show saturated charge carrier mobilities, μFET, as high as 2 × 10–2 cm2 V–1 s–1 and ON‐OFF ratios, Ion/Ioff ∼ 105 at contents of the insulating PE moiety as high as 90 wt %. In addition, the diblock copolymers display outstanding flexibility and toughness with elongations at break exceeding 600 % and true tensile strengths around 70 MPa, opening the path towards robust and truly flexible electronic components.
Diblock copolymers of polyethylene and regioregular poly(3‐hexylthiophene) show saturated charge‐carrier mobilities μFET as high as 2\.10‐2 cm2/Vs, ON‐OFF ratios Ion/Ioff ∼105, elongations at break >600 % and true tensile strengths ∼70 MPa at contents of the insulating PE moiety as high as 90 wt%.
For successful CO2 storage in underground reservoirs, the potential problem of CO2 leakage needs to be addressed. A profoundly improved understanding of the behavior of fractured cement under ...realistic subsurface conditions including elevated temperature, high pressure and the presence of CO2 saturated brine is required. Here, we report in situ X-ray micro computed tomography (μ-CT) studies visualizing the microstructural changes upon exposure of cured Portland cement with an artificially engineered leakage path (cavity) to CO2 saturated brine at high pressure. Carbonation of the bulk cement, self-healing of the leakage path in the cement specimen, and leaching of CaCO3 were thus directly observed. The precipitation of CaCO3, which is of key importance as a possible healing mechanism of fractured cement, was found to be enhanced in confined regions having limited access to CO2. For the first time, the growth kinetics of CaCO3 under more realistic well conditions have thus been estimated quantitatively. Combining the μ-CT observations with scanning electron microscopy resulted in a detailed understanding of the processes involved in the carbonation of cement.
Ordered graphene films have been fabricated on Fe-treated SiC and diamond surfaces using the catalytic conversion of sp3 to sp2 carbon. In comparison with the bare SiC (0001) surface, the ...graphitization temperature is reduced from over 1000°C to 600°C and for diamond (111), this new approach enables epitaxial graphene to be grown on this surface for the first time. For both substrates, a key development is the in situ monitoring of the entire fabrication process using real-time electron spectroscopy that provides the necessary precision for the production of films of controlled thickness. The quality of the graphene/graphite layers has been verified using angle-resolved photoelectron spectroscopy, scanning tunneling microscopy and low energy electron diffraction. Graphene is only formed on treated regions of the surface and so this offers a method for fabricating and patterning graphene structures on SiC and diamond in the solid-state at industrially realistic temperatures.
The formation of calcium carbonate (CaCO
) nanoparticles (NPs) in the presence of polystyrene sulfonate (PSS) as an additive was examined by time-resolved small-angle X-ray scattering (SAXS) in a ...flow system that mimics experimental conditions used at home facilities where the precipitation can be achieved in a beaker. The experiments were carried out at low concentrations to remain in the dilute regime. A model-independent analysis was performed using the Porod invariant which defines the scale factor, leaving only the distribution of radii as the adjustable parameter. The presence of the PSS additive strongly retards the precipitation of CaCO
NPs. The formation of NPs reaches a state of equilibrium after a few minutes. Here, it is shown that the concentration of precursors at a fixed PSS concentration plays a key role in determining the size of the NPs obtained. A full analysis of the SAXS patterns was carried out using the Hurd-Flower model to account for the weaker intensity decay than the classical Porod behaviour. The temporal evolution of the particle radii was determined. Wide-angle X-ray scattering experiments carried out simultaneously show that the particles formed have the structure of vaterite with growth consistent with the evolution of the Porod invariant.
Very high conductivities (>1000
S/cm) were obtained in poly(3,4-ethylenedioxythiophene) films oxidized with Fe(III)tosylate when the acidity during the polymerization process was controlled using a ...basic inhibitor. The best results were obtained with pyridine as inhibitor. The films could either be polymerized from a solution of 3,4-ethylenedioxythiophene (EDT), Fe(III)tosylate and pyridine or by vapor phase polymerization (VPP) of EDT on a surface coated with Fe(III)tosylate and pyridine.
By incorporating non-conducting adhesive (up to 75% vol.) in the vapor phase polymerized PEDT system, films with activation energy of 1/3 the value of pure PEDT, were obtained. The reason for this phenomenon could
not be explained by changes in the PEDT structure investigated with grazing incidence X-ray diffraction.
Chloroform is a general solvent for poly(3-hexylthiophene) (P3HT) active layers in field-effect transistors. However, its low boiling point and rapid evaporation limit the time for crystallization ...during the spin-coating process, and field-effect mobilities achieved for P3HT films spin-coated from chloroform are typically on the order of 0.01 cm2/(V s). Here we investigate a range of solvents with higher boiling points. We find that 1,2,4-trichlorobenzene with good solubility and a high boiling point significantly improves the field-effect mobilities up to 0.12 cm2/(V s) with on:off ratios of 106. By controlling the microstructure through the choice of solvent while keeping the molecular weight fixed, we observe a clear correlation between the field-effect mobility and the degree of microcrystalline order as measured by X-ray diffraction, as well as the strength of polaronic relaxation of charge carriers in the accumulation layer as measured by optical spectroscopy of field-induced charge.
The formation of calcium carbonate (CaCO3) nanoparticles (NPs) in the presence of polystyrene sulfonate (PSS) as an additive was examined by time‐resolved small‐angle X‐ray scattering (SAXS) in a ...flow system that mimics experimental conditions used at home facilities where the precipitation can be achieved in a beaker. The experiments were carried out at low concentrations to remain in the dilute regime. A model‐independent analysis was performed using the Porod invariant which defines the scale factor, leaving only the distribution of radii as the adjustable parameter. The presence of the PSS additive strongly retards the precipitation of CaCO3 NPs. The formation of NPs reaches a state of equilibrium after a few minutes. Here, it is shown that the concentration of precursors at a fixed PSS concentration plays a key role in determining the size of the NPs obtained. A full analysis of the SAXS patterns was carried out using the Hurd–Flower model to account for the weaker intensity decay than the classical Porod behaviour. The temporal evolution of the particle radii was determined. Wide‐angle X‐ray scattering experiments carried out simultaneously show that the particles formed have the structure of vaterite with growth consistent with the evolution of the Porod invariant.
The kinetics of precipitation of CaCO3 particles in the presence of polystyrene sulfonate was studied by small‐ and wide‐angle X‐ray scattering. Employment of the Porod invariant and the Hurd–Flower model provides essential information on the kinetics.
For successful CO
storage in underground reservoirs, the potential problem of CO
leakage needs to be addressed. A profoundly improved understanding of the behavior of fractured cement under realistic ...subsurface conditions including elevated temperature, high pressure and the presence of CO
saturated brine is required. Here, we report in situ X-ray micro computed tomography (μ-CT) studies visualizing the microstructural changes upon exposure of cured Portland cement with an artificially engineered leakage path (cavity) to CO
saturated brine at high pressure. Carbonation of the bulk cement, self-healing of the leakage path in the cement specimen, and leaching of CaCO
were thus directly observed. The precipitation of CaCO
, which is of key importance as a possible healing mechanism of fractured cement, was found to be enhanced in confined regions having limited access to CO
. For the first time, the growth kinetics of CaCO
under more realistic well conditions have thus been estimated quantitatively. Combining the μ-CT observations with scanning electron microscopy resulted in a detailed understanding of the processes involved in the carbonation of cement.
Block copolymers of regioregular poly(3-hexylthiophene) (P3HT) and polyethylene (PE) were synthesized through the chain transfer of olefin-terminated P3HT in the presence of cyclooctene via ...ring-opening metathesis polymerization (ROMP). Subsequent hydrogenation of the poly(cyclooctene) block yielded high molecular weight, crystalline−crystalline P3HT-PE block copolymers, which are thermally stable and resistant to solvents under ambient conditions. These copolymers were characterized by 1H NMR, DSC, and WAXS and represent the first materials of a class of crystalline−crystalline semiconducting−insulating block copolymers.