Colliders are built on a foundation of superconducting magnet technology that provides strong dipole magnets to maintain the beam orbit and strong focusing magnets to enable the extraordinary ...luminosity required to probe physics at the energy frontier. The dipole magnet strength plays a critical role in dictating the energy reach of a collider, and the superconducting magnets are arguably the dominant cost driver for future collider facilities. As the community considers opportunities to explore new energy frontiers, the importance of advanced magnet technology - both in terms of magnet performance and in the magnet technology's potential for cost reduction - is evident, as the technology status is essential for informed decisions on targets for physics reach and facility feasibility.
Continuous and recycling cultures were carried out with Aspergillus niger N402 wild-type and a glucoamylase overproducing transformant to investigate growth and product formation characteristics. In ...shake flask cultures, the amount of glucoamylase produced by the transformant was about five times more than by the wild-type strain. In contrast with these results, a twofold overproduction was found in glucose-limited continuous cultures, while no overproduction was found under maltodextrin-limitation. Two regions of specific growth rates could be distinguished, one at specific growth rates lower (domain I) and one at specific growth rates higher than 0.12 h-1 (domain II). In domain I changes in mycelium morphology and conidia formation were observed. It has been concluded that maintenance requirements are dependent on the specific growth rate over the whole range of measured growth rates. The deviation in linearity in the linear equation of substrate utilization, caused by this phenomenon, should be considered when continuous cultures with filamentous fungi are performed. In recycling cultures, xylose as limiting carbon source repressed glucoamylase production very strongly. Under maltodextrin-limitation a fivefold overproduction as found. After about 150 h, the total amount of glucoamylase produced was still increasing, while total amount of product, measured as carbon, remained constant. After this time no increase in the amount of biomass formed was observed. These results suggest autolysis and cryptic growth taking place in a recycling fermenter and cell death rate equalling growth rate.
Insertion Magnets Ambrosio, G; Anerella, M; Bossert, R ...
arXiv.org,
05/2017
Paper, Journal Article
Odprti dostop
Chapter 3 in High-Luminosity Large Hadron Collider (HL-LHC) : Preliminary Design Report. The Large Hadron Collider (LHC) is one of the largest scientific instruments ever built. Since opening up a ...new energy frontier for exploration in 2010, it has gathered a global user community of about 7,000 scientists working in fundamental particle physics and the physics of hadronic matter at extreme temperature and density. To sustain and extend its discovery potential, the LHC will need a major upgrade in the 2020s. This will increase its luminosity (rate of collisions) by a factor of five beyond the original design value and the integrated luminosity (total collisions created) by a factor ten. The LHC is already a highly complex and exquisitely optimised machine so this upgrade must be carefully conceived and will require about ten years to implement. The new configuration, known as High Luminosity LHC (HL-LHC), will rely on a number of key innovations that push accelerator technology beyond its present limits. Among these are cutting-edge 11-12 tesla superconducting magnets, compact superconducting cavities for beam rotation with ultra-precise phase control, new technology and physical processes for beam collimation and 300 metre-long high-power superconducting links with negligible energy dissipation. The present document describes the technologies and components that will be used to realise the project and is intended to serve as the basis for the detailed engineering design of HL-LHC.
As superconducting magnet technology is pushed towards higher performance, energy density and total stored energy follow exponentially. Protecting magnets becomes substantially more challenging with ...traditional methods being stretched to their limits. New technologies such as CLIQ (Coupling Loss Induced Quench) promise to provide a robust method to protect advanced magnets, however they become inductance limited in large magnet strings or at low field, leading to more complex configurations. A technique to substantially reduce this limitation and improve response time is presented, by winding coils in a bifilar fashion and connecting them in series for typical operation, while providing an anti-parallel connection for quasi-zero-inductance in a protection case. This allows for extremely high di/dt. The concept is then demonstrated on a small REBCO coil.
UMEP (Urban Multi-scale Environmental Predictor), a city-based climate service tool, combines models and tools essential for climate simulations. Applications are presented to illustrate UMEP's ...potential in the identification of heat waves and cold waves; the impact of green infrastructure on runoff; the effects of buildings on human thermal stress; solar energy production; and the impact of human activities on heat emissions. UMEP has broad utility for applications related to outdoor thermal comfort, wind, urban energy consumption and climate change mitigation. It includes tools to enable users to input atmospheric and surface data from multiple sources, to characterise the urban environment, to prepare meteorological data for use in cities, to undertake simulations and consider scenarios, and to compare and visualise different combinations of climate indicators. An open-source tool, UMEP is designed to be easily updated as new data and tools are developed, and to be accessible to researchers, decision-makers and practitioners.
•A GIS-based climate planning tool for researcher and practitioners is presented.•UMEP has broad utility for applications related to e.g. climate change mitigation.•Applications are presented to illustrate UMEP's potential.
Epoxy resins have long been a focus of magnet design. They provide strength and stability to the superconductor, to allow coil fabrication and consistent magnet performance. They are often cited as a ...main contributor to magnet performance, often as a limiting factor, from epoxy cracking and energy release. New resin systems are being designed to improve magnet quench and training performance through several means. Baseline candidate resin systems are evaluated for neat resin mechanical properties as well as behavior in Nb 3 Sn subscale composites. This data feeds additional resin system tuning to meet the goals stated above.
Epoxy resins have long been a focus of magnet design. They provide strength and stability to the superconductor, to allow coil fabrication and consistent magnet performance. They are often cited as a ...main contributor to magnet performance, often as a limiting factor, from epoxy cracking and energy release. New resin systems are being designed to improve magnet quench and training performance through several means. Baseline candidate resin systems are evaluated for neat resin mechanical properties as well as behavior in Nb3Sn subscale composites. Furthermore, this data feeds additional resin system tuning to meet the goals stated above.
With the successful test of the first two pre-series magnets the US HL-LHC Accelerator Upgrade Project has started production of the MQXFA magnets to be used in Q1/Q3 inner triplet elements of the ...HL-LHC. This good start comes after the test of two prototypes with limited performance, and it demonstrates the importance of learning from past issues. Therefore, in this paper we want to share the most important lessons learned so far, focusing on those which may be more interesting for similar projects. We will also present the status of MQXFA fabrication in the US.
In superconducting magnets, the irreversible transition of a portion of the conductor to resistive state is called a "quench." Having large stored energy, magnets can be damaged by quenches due to ...localized heating, high voltage, or large force transients. Unfortunately, current quench protection systems can only detect a quench after it happens, and mitigating risks in Low Temperature Superconducting (LTS) accelerator magnets often requires fast response (down to ms). Additionally, protection of High Temperature Superconducting (HTS) magnets is still suffering from prohibitively slow quench detection. In this study, we lay the groundwork for a quench prediction system using an auto-encoder fully-connected deep neural network. After dynamically trained with data features extracted from acoustic sensors around the magnet, the system detects anomalous events seconds before the quench in most of our data. While the exact nature of the events is under investigation, we show that the system can "forecast" a quench before it happens under magnet training conditions through a randomized experiment. This opens up the way of integrated data processing, potentially leading to faster and better diagnostics and detection of magnet quenches.
PDF
