Magnet programs at BNL, LBNL and FNAL have observed instabilities in high J/sub c/ Nb/sub 3/Sn strands and magnets made from these strands. This paper correlates the strand stability determined from ...a short sample-strand test to the observed magnet performance. It has been observed that strands that carry high currents at high fields (greater than 10 T) cannot sustain these same currents at low fields (1-3 T) when the sample current is fixed and the magnetic field is ramped. This suggests that the present generation of strand is susceptible to flux jumps (FJ). To prevent flux jumps from limiting stand performance, one must accommodate the energy released during a flux jump. To better understand FJ this work has focused on wire with a given sub-element diameter and shows that one can significantly improve stability by increasing the copper conductivity (higher residual resistivity ratio, RRR, of the Cu). This increased stability significantly improves the conductor performance and permits it to carry more current.
In 2004, the US DOE established the LHC Accelerator Research Program (LARP) with the goal of developing a technology base for future upgrades of the LHC. The focus of the magnet program, which is a ...collaboration of three US laboratories, BNL, FNAL and LBNL, is on development of high gradient quadrupoles using Nb 3 Sn superconductor. Other program components address issues regarding magnet design, radiation-hard materials, long magnet scale-up, quench protection, fabrication techniques and conductor and cable R&D. This paper presents an overall view of the program with emphasis on the current quadrupole project and outlines the long-term goals of the program
LBNL is using pressurized bladders in its high field superconducting magnet program Magnet RD3; a 14 T race track dipole, has been assembled and pre-stressed using such a system. The bladder, placed ...between the coil pack and the iron yoke, can provide 70 MPa of pressure while compressing the coil pack and tensioning a 40 mm thick structural aluminum shell. Interference keys replace the bladder's functionality as they are deflated and removed leaving the shell in 140 MPa of tension. During cool down, stress in the shell increases to 250 MPa as a result of the difference in thermal expansion between the aluminum shell and the inner iron yoke. A number of strain gauges mounted onto the shell were used to monitor its strain during assembly, cool-down and testing. This technique ensures that the final and maximum stress in the shell is reached before the magnet is ever energized. The use of a structural shell and pressurized bladders has simplified magnet assembly considerably. In this paper we describe the bladder system and its use in the assembly of a 14 T Nb/sub 3/Sn magnet.
The Superconducting Magnet Group at Lawrence Berkeley National Laboratory (LBNL) has been developing 3D finite element models to predict the behavior of high field Nb 3 Sn superconducting magnets. ...The models track the coil response during assembly, cool-down, and excitation, with particular interest on displacements when frictional forces arise. As Lorentz forces were cycled, irreversible displacements were computed and compared with strain gauge measurements. Additional analysis was done on the local frictional energy released during magnet excitation, and the resulting temperature rise. Magnet quenching and training was correlated to the level of energy release during such mechanical displacements under frictional forces. We report in this paper the computational results of the ratcheting process, the impact of friction, and the path-dependent energy release leading to a computed magnet training curve.
Test results are reported on four quadrupole magnet model tests (TQS01a, TQS01b, TQS01c, TQS02) in support of the development of a large-aperture superconducting quadrupole for the US LHC Accelerator ...Research Program (LARP). All four magnet assemblies used key and bladder technology to compress and support the coils within an iron yoke and an aluminum shell. The first three models tested different magnet assemblies of several coils, having MJR conductor, and gapped segmented bronze pole-islands. TQS02's coils utilized improved (RRP) conductor, and addressed TQS01's quench-training pattern, by utilizing titanium alloy (TiAl6V4) pole-islands, with no axial gaps during reaction. This paper summarizes the assembly, cool-down and performance of TQS01a, TQS01b, TQS01c, and TQS02 and compares measurements with design expectations.
... in order to further develop the block-coil geometry for future high-field accelerators, the bore size has to be increased to 30-50 mm. With respect to HD1, the main R&D challenges are: (a) design ...of the coil ends, to allow a magnetically efficient cross-section without obstructing the beam path; (b) design of the bore, to support the coil against the pre-load force; (c) correction of the geometric field errors.
Test results for HD1, a 16 tesla Nb3Sn dipole magnet LIETZKE, A. F; BARTLETT, S; HIGLEY, H ...
IEEE transactions on applied superconductivity,
06/2004, Letnik:
14, Številka:
2
Conference Proceeding, Journal Article
We present two techniques used in the analysis of voltage tap data collected during recent tests of superconducting magnets developed by the Superconducting Magnet Program at Lawrence Berkeley ...National Laboratory. The first technique was used on a quadrupole to provide information about quench origins that could not be obtained using the time-of-flight method. The second technique illustrates the use of data from transient flux imbalances occurring during magnet ramping to diagnose changes in the current–temperature margin of a superconducting cable. In both cases, the results of this analysis contributed to make improvements on subsequent magnets.
The Superconducting Magnet Program at LBNL has developed a magnet design supporting our new Subscale Magnet Program, that facilitates rapid testing of small superconducting racetrack coils in the ...field range of 10-12 Tesla. Several coils have been made from a variety of Nb/sub 3/Sn/Cu cables, insulated, wound, reacted, potted and assembled into a small reusable yoke and shell loading structure. Bladder and key technology have provided a rapid and efficient means for adjusting coil pre-stress during both initial assembly, and between thermal cycles. This affords the opportunity to test moderately long rectangular cable samples under "magnet conditions" on a time scale considerably closer to that for traditional short-sample cable tests. We have built and tested four coils with the initial aim of determining the feasibility of reducing overall conductor costs with "mixed-strand" cables. Details of cost reduction improvements, coil construction, magnet structure, and assembly procedures are reported, along with the relative performance of the mixed-strand coil.
PDF
