An electronic (e‐) skin is expected to experience significant wear and tear over time. Therefore, self‐healing stretchable materials that are simultaneously soft and with high fracture energy, that ...is high tolerance of damage or small cracks without propagating, are essential requirements for the realization of robust e‐skin. However, previously reported elastomers and especially self‐healing polymers are mostly viscoelastic and lack high mechanical toughness. Here, a new class of polymeric material crosslinked through rationally designed multistrength hydrogen bonding interactions is reported. The resultant supramolecular network in polymer film realizes exceptional mechanical properties such as notch‐insensitive high stretchability (1200%), high toughness of 12 000 J m−2, and autonomous self‐healing even in artificial sweat. The tough self‐healing materials enable the wafer‐scale fabrication of robust and stretchable self‐healing e‐skin devices, which will provide new directions for future soft robotics and skin prosthetics.
An extremely tough and water‐insensitive self‐healing elastomer crosslinked through multistrength hydrogen bonding interactions is described. The resultant crosslinking network in polymer film realizes exceptional mechanical properties such as notch‐insensitive high stretchability (1200%), a high toughness of 12 000 J m−2, and autonomous self‐healing even in artificial sweat. The tough self‐healing materials enable the wafer‐scale fabrication of robust and stretchable self‐healing e‐skin devices.
Nonconjugated segments in polymer semiconductors have been utilized to improve the processability of semiconducting polymers. Recently, several reports have described the improvement of ...stretchability of polymer semiconductors by incorporating nonconjugated spacers. However, the effect of relative flexibility of such conjugation breakers on mechanical and electrical properties has not yet been studied systematically. Here, conjugation breakers with different chain length and rigidity are incorporated into the backbone of diketopyrrolopyrrole‐based semiconductors. Interestingly, it is observed that the longer and more flexible conjugation breakers result in greater ductility and lower elastic modulus without significantly affecting mobility. The enhancement of stretchability is attributed to the reduced modulus and the decrease in crystallinity, as confirmed by X‐ray diffraction. With this newly established molecular design, transistors are prepared with a semiconducting polymer containing dodecyl segments as conjugation breakers. It is observed that this polymer retains a mobility of >0.36 cm2 V−1 s−1 at 100% strain, and after 100 cycles at 50% strain. Finally, its high stability against strain is also observed with a fully stretchable transistor fabricated. Taken together, the above results indicate that molecular engineering of conjugated polymers, i.e., by incorporating suitable conjugation breakers, can effectively tune mechanical properties without significantly compromising their electrical properties.
The effect of nonconjugated spacers on mechanical properties of polymer semiconductors is discussed. Longer and more flexible conjugation breakers lead to greater ductility and lower modulus without significant compromise in mobility. Specifically, a semiconducting polymer containing dodecyl segments maintains a moderate mobility (≈0.1 cm2 V−1 s−1) under 100% strain, and after 100 cycles at 50% strain.
The electrodeposition of lithium metal is a key process in next-generation, high energy density storage devices. However, the high reactivity of the lithium metal causes short cycling lifetimes and ...dendrite growth that can pose a serious safety issue. Recently, a number of approaches have been pursued to stabilize the lithium metal–electrolyte interface, including soft polymeric coatings that have shown the ability to enable high-rate and high-capacity lithium metal cycling, but a clear understanding of how to design and modify these coatings has not yet been established. In this work, we studied the effects of several polymers with systematically varied chemical and mechanical properties as coatings on the lithium metal anode. By examining the early stages of lithium metal deposition, we determine that the morphology of the lithium particles is strongly influenced by the chemistry of the polymer coating. We have identified polymer dielectric constant and surface energy as two key descriptors of the lithium deposit size. Low surface energy polymers were found to promote larger deposits with smaller surface areas. This may be explained by a reduced interaction between the coating and the lithium surface and thus an increase in the interfacial energy. On the other hand, high dielectric constant polymers were found to increase the exchange current and gave larger lithium deposits due to the decreased overpotentials at a fixed current density. We also observed that the thickness of the polymer coating should be optimized for each individual polymer. Furthermore, polymer reactivity was found to strongly influence the Coulombic efficiency. Overall, this work offers new fundamental insights into lithium electrodeposition processes and provides direction for the design of new polymer coatings to better stabilize the lithium metal anode.
Stretchable semiconducting polymers have been developed as a key component to enable skin-like wearable electronics, but their electrical performance must be improved to enable more advanced ...functionalities. Here, we report a solution processing approach that can achieve multi-scale ordering and alignment of conjugated polymers in stretchable semiconductors to substantially improve their charge carrier mobility. Using solution shearing with a patterned microtrench coating blade, macroscale alignment of conjugated-polymer nanostructures was achieved along the charge transport direction. In conjunction, the nanoscale spatial confinement aligns chain conformation and promotes short-range π-π ordering, substantially reducing the energetic barrier for charge carrier transport. As a result, the mobilities of stretchable conjugated-polymer films have been enhanced up to threefold and maintained under a strain up to 100%. This method may also serve as the basis for large-area manufacturing of stretchable semiconducting films, as demonstrated by the roll-to-roll coating of metre-scale films.
The promise of wearable and implantable devices has made stretchable organic semiconductors highly desirable. Though there are increasing attempts to design intrinsically stretchable conjugated ...polymers, their performance in terms of charge carrier mobility and maximum fracture strain is still lacking behind extrinsic approaches (i.e., buckling, Kirigami interconnects). Here, polymer crosslinking with flexible oligomers is applied as a strategy to reduce the tensile modulus and improve fracture strain, as well as fatigue resistance for a high mobility diketopyrrolopyrrole polymer. These polymers are crosslinked with siloxane oligomers to give stretchable films stable up to a strain ε = 150% and 500 strain‐and‐release cycles of 100% strain without the formation of nanocracks. Organic field‐effect transistors are prepared to assess the electrical properties of the crosslinked film under cyclic strain loading. An initial average mobility (μavg) of 0.66 cm2 V−1 s−1 is measured at 0% strain. A steady μavg above 0.40 cm2 V−1 s−1 is obtained in the direction perpendicular to the strain direction after 500 strain‐and‐release cycles of 20% strain. The μavg in the direction parallel to strain, however, is compromised due to the formation of wrinkles.
Improved elastic property in diketopyrrolopyrrole polymer is achieved by crosslinking with a flexible siloxane oligomer. An enhancement in fracture strain and yielding point and a decrease in tensile modulus with film crystalinity are observed. The improved fatigue resistance is attributed to the covalent crosslinks that prevent irreversible sliding between polymer chains during cyclic loading.
Skin-like electronics that can adhere seamlessly to human skin or within the body are highly desirable for applications such as health monitoring, medical treatment, medical implants and biological ...studies, and for technologies that include human-machine interfaces, soft robotics and augmented reality. Rendering such electronics soft and stretchable-like human skin-would make them more comfortable to wear, and, through increased contact area, would greatly enhance the fidelity of signals acquired from the skin. Structural engineering of rigid inorganic and organic devices has enabled circuit-level stretchability, but this requires sophisticated fabrication techniques and usually suffers from reduced densities of devices within an array. We reasoned that the desired parameters, such as higher mechanical deformability and robustness, improved skin compatibility and higher device density, could be provided by using intrinsically stretchable polymer materials instead. However, the production of intrinsically stretchable materials and devices is still largely in its infancy: such materials have been reported, but functional, intrinsically stretchable electronics have yet to be demonstrated owing to the lack of a scalable fabrication technology. Here we describe a fabrication process that enables high yield and uniformity from a variety of intrinsically stretchable electronic polymers. We demonstrate an intrinsically stretchable polymer transistor array with an unprecedented device density of 347 transistors per square centimetre. The transistors have an average charge-carrier mobility comparable to that of amorphous silicon, varying only slightly (within one order of magnitude) when subjected to 100 per cent strain for 1,000 cycles, without current-voltage hysteresis. Our transistor arrays thus constitute intrinsically stretchable skin electronics, and include an active matrix for sensory arrays, as well as analogue and digital circuit elements. Our process offers a general platform for incorporating other intrinsically stretchable polymer materials, enabling the fabrication of next-generation stretchable skin electronic devices.
In order to apply polymer semiconductors to stretchable electronics, they need to be easily deformed under strain without being damaged. A small number of conjugated polymers, typically with ...semicrystalline packing structures, have been reported to exhibit mechanical stretchability. Herein, a method is reported to modify polymer semiconductor packing‐structure using a molecular additive, dioctyl phthalate (DOP), which is found to act as a molecular spacer, to be inserted between the amorphous chain networks and disrupt the crystalline packing. As a result, large‐crystal growth is suppressed while short‐range aggregations of conjugated polymers are promoted, which leads to an improved mechanical stretchability without affecting charge‐carrier transport. Due to the reduced conjugated polymer intermolecular interactions, strain‐induced chain alignment and crystallization are observed. By adding DOP to a well‐known conjugated polymer, poly2,5‐bis(4‐decyltetradecyl)pyrrolo3,4‐cpyrrole‐1,4‐(2H,5H)‐dione‐(E)‐1,2‐di(2,2′‐bithiophen‐5‐yl)ethene (DPPTVT), stretchable transistors are obtained with anisotropic charge‐carrier mobilities under strain, and stable current output under strain up to 100%.
Bulky additive molecules residing between amorphous chain networks can disrupt the crystalline ordering of polymer semiconductors. The long‐range crystalline domains are suppressed while short‐range aggregations of conjugated polymers are promoted, leading to an improved thin‐film stretchability without affecting charge transport under an external strain up to 100%.
Molecular additives are often used to enhance dynamic motion of polymeric chains, which subsequently alter the functional and physical properties of polymers. However, controlling the chain dynamics ...of semiconducting polymer thin films and understanding the fundamental mechanisms of such changes is a new area of research. Here, cycloparaphenylenes (CPPs) are used as conjugated molecular additives to tune the dynamic behaviors of diketopyrrolopyrrole‐based (DPP‐based) semiconducting polymers. It is observed that the addition of CPPs results in significant improvement in the stretchability of the DPP‐based polymers without adversely affecting their mobility, which arises from the enhanced polymer dynamic motion and reduced long‐range crystalline order. The polymer films retain their fiber‐like morphology and short‐range ordered aggregates, which leads to high mobility. Fully stretchable transistors are subsequently fabricated using CPP/semiconductor composites as active layers. These composites are observed to maintain high mobilities when strained and after repeated applied strains. Interestingly, CPPs are also observed to improve the contact resistance and charge transport of the fully stretchable transistors. ln summary, these results collectively indicate that controlling the dynamic motion of polymer semiconductors is proved to be an effective way to improve their stretchability.
Conjugated carbon cyclic nanoring compounds are used as molecular additives to enhance the stretchability of semiconducting polymers without compromising mobility. The additives are shown to significantly decrease long‐range crystalline order, while short‐range ordered aggregates are well‐maintained. Fully stretchable transistors fabricated with the newly established polymer semiconductor/molecular additive blend films exhibit improved mobility retention under strain and after repeated applied strain.
Abstract
Intrinsically and fully stretchable active-matrix-driven displays are an important element to skin electronics that can be applied to many emerging fields, such as wearable electronics, ...consumer electronics and biomedical devices. Here, we show for the first time a fully stretchable active-matrix-driven organic light-emitting electrochemical cell array. Briefly, it is comprised of a stretchable light-emitting electrochemical cell array driven by a solution-processed, vertically integrated stretchable organic thin-film transistor active-matrix, which is enabled by the development of chemically-orthogonal and intrinsically stretchable dielectric materials. Our resulting active-matrix-driven organic light-emitting electrochemical cell array can be readily bent, twisted and stretched without affecting its device performance. When mounted on skin, the array can tolerate to repeated cycles at 30% strain. This work demonstrates the feasibility of skin-applicable displays and lays the foundation for further materials development.
PDF
