VSE knjižnice (vzajemna bibliografsko-kataložna baza podatkov COBIB.SI)
-
Influence of cooling speed on the microstructure and wear behaviour of hypereutectic FeCrC hardfacingsHornung, J. ...The main focus of this work is to show influences of the cooling rate on the microstructure and wear performance of Fe-Cr-C hardfacings. The coatings were produced by welding. The weld overlays were ... cooled from the molten stage in selected variations: (i) standard cooling - cooling on air at the steel welding table; (ii) passive cooling - cooling of the base material during the hardfacing process with a water cooled cooper plate with 12 1C; (iii) active cooling - cooling of the welding seam behind the main arc with CO2 gas at temperature of -80 1C. For each cooling situation the temperature of the weld seam was measured in the melt pool with help of thermocouple. It was shown, that different cooling conditions can lead to the significant changes in the cooling-off time t8/5, dilution of the hardfacing with substrate and microstructural features of the hardfacings under investigation. Three different wear tests (three-body abrasion according to ASTM G65 standard, impact/abrasion and solid particle erosion) were performed to study the wear performances of Fe-Cr-C hardfacing. Testing results have shown that if the cooling-off time t8/5 is too short it influences the brittleness and increases the residual stresses of the Fe-Cr-C hardfacing, which lowers its impact resistance. The effect of the cooling rate is in good correlation with wear test results and gives promise for further microstructure and process optimisation for the improved tribological performance.Vir: Materials Science & Engineering. A, Structural materials: Properties, Microstructure and Processing. - ISSN 0921-5093 (Vol. 576, 2013, str. 243-251)Vrsta gradiva - članek, sestavni delLeto - 2013Jezik - angleškiCOBISS.SI-ID - 12832283
Avtor
Hornung, J. |
Zikin, A. |
Pichelbauer, K. |
Kalin, Mitjan |
Kirchgaßner, M.
Teme
hitrost hlajenja |
erozija |
tribologija |
obraba |
zaostale napetosti |
Fe-Cr-C |
cooling speed |
erosion |
tribology |
abrasion |
residual stresses
vir: Materials Science & Engineering. A, Structural materials: Properties, Microstructure and Processing. - ISSN 0921-5093 (Vol. 576, 2013, str. 243-251)
Vnos na polico
Trajna povezava
- URL:
Faktor vpliva
Dostop do baze podatkov JCR je dovoljen samo uporabnikom iz Slovenije. Vaš trenutni IP-naslov ni na seznamu dovoljenih za dostop, zato je potrebna avtentikacija z ustreznim računom AAI.
Leto | Faktor vpliva | Izdaja | Kategorija | Razvrstitev | ||||
---|---|---|---|---|---|---|---|---|
JCR | SNIP | JCR | SNIP | JCR | SNIP | JCR | SNIP |
Baze podatkov, v katerih je revija indeksirana
Ime baze podatkov | Področje | Leto |
---|
Povezave do osebnih bibliografij avtorjev | Povezave do podatkov o raziskovalcih v sistemu SICRIS |
---|---|
Hornung, J. | |
Zikin, A. | |
Pichelbauer, K. | |
Kalin, Mitjan | 14556 |
Kirchgaßner, M. |
Vir: Osebne bibliografije
in: SICRIS
Izberite prevzemno mesto:
Prevzem gradiva po pošti
Naslov za dostavo:
Med podatki člana manjka naslov.
Storitev za pridobivanje naslova trenutno ni dostopna, prosimo, poskusite še enkrat.
S klikom na gumb "V redu" boste potrdili zgoraj izbrano prevzemno mesto in dokončali postopek rezervacije.
S klikom na gumb "V redu" boste potrdili zgoraj izbrano prevzemno mesto in naslov za dostavo ter dokončali postopek rezervacije.
S klikom na gumb "V redu" boste potrdili zgoraj izbrani naslov za dostavo in dokončali postopek rezervacije.
Obvestilo
Trenutno je storitev za avtomatsko prijavo in rezervacijo nedostopna. Gradivo lahko rezervirate sami na portalu Biblos ali ponovno poskusite tukaj kasneje.
Gesla v Splošnem geslovniku COBISS
Izbira mesta prevzema
Gradivo iz matične enote je brezplačno. Če je gradivo na mesto prevzema dostavljeno iz drugih enot, lahko knjižnica to storitev zaračuna.
Mesto prevzema | Status gradiva | Rezervacija |
---|
Rezervacija v teku
Prosimo, počakajte trenutek.
Rezervacija je uspela.
Rezervacija ni uspela.
Rezervacija...
Članska izkaznica:
Mesto prevzema: