VSE knjižnice (vzajemna bibliografsko-kataložna baza podatkov COBIB.SI)
-
Initiation and evolution of the aluminium-alloy transfer on hot-work tool steel at temperatures from 20 °C to 500 °CJerina, Jure ; Kalin, MitjanDuring the forming of aluminium alloys there are several difficulties associated with controlling the process parameters and the product quality due to the severity of the contact. Adhesion and, in ... particular, the formation of transfer films of aluminium alloys on the surfaces of hot-work tool steels are very negative phenomena in this process and require a better understanding. The present work is focused on the initiation and evolution of the transfer of the aluminium alloy EN AW-6060 to the nitrided hot-work tool steel AISI H13 in the temperature range from 20 °C to 500 °C. All the tests were performed under cross cylinder single-pass, dry-sliding-contact conditions over different sliding distances. The contact was investigated in terms of the surface area and the volume of the transferred aluminium alloy to the surface of the tool steel, the topography of the wear trace and the corresponding coefficient of friction. The results show the strong dependence of the tribological properties in the contacts of the nitrided hot-work tool steel and the aluminium alloy on the temperature. However, it was found that the whole tribological behaviour is largely already defined during the very early stages of sliding, i.e., at the initiation of sliding, after which it becomes even more pronounced as the temperature increases. At low temperatures (20-200 °C) the surface roughness of the tool steel was found to be the key initial cause of the aluminium alloyʼs transfer, while at higher temperatures (300-500 °C) this transfer occurred predominantly due to strong adhesion.Vir: Wear. - ISSN 0043-1648 (Vol. 319, iss. 1/2, Nov. 2014, str. 234-244)Vrsta gradiva - članek, sestavni delLeto - 2014Jezik - angleškiCOBISS.SI-ID - 13686299
Avtor
Jerina, Jure |
Kalin, Mitjan
Teme
hot-work tool steels |
aluminium alloys |
adhesion |
material transfers |
friction |
elevated temperatures |
orodna jekla |
aluminijeve zlitine |
trenje |
mazanje
Vnos na polico
Trajna povezava
- URL:
Faktor vpliva
Dostop do baze podatkov JCR je dovoljen samo uporabnikom iz Slovenije. Vaš trenutni IP-naslov ni na seznamu dovoljenih za dostop, zato je potrebna avtentikacija z ustreznim računom AAI.
Leto | Faktor vpliva | Izdaja | Kategorija | Razvrstitev | ||||
---|---|---|---|---|---|---|---|---|
JCR | SNIP | JCR | SNIP | JCR | SNIP | JCR | SNIP |
Baze podatkov, v katerih je revija indeksirana
Ime baze podatkov | Področje | Leto |
---|
Povezave do osebnih bibliografij avtorjev | Povezave do podatkov o raziskovalcih v sistemu SICRIS |
---|---|
Jerina, Jure | 33243 |
Kalin, Mitjan | 14556 |
Vir: Osebne bibliografije
in: SICRIS
Izberite prevzemno mesto:
Prevzem gradiva po pošti
Naslov za dostavo:
Med podatki člana manjka naslov.
Storitev za pridobivanje naslova trenutno ni dostopna, prosimo, poskusite še enkrat.
S klikom na gumb "V redu" boste potrdili zgoraj izbrano prevzemno mesto in dokončali postopek rezervacije.
S klikom na gumb "V redu" boste potrdili zgoraj izbrano prevzemno mesto in naslov za dostavo ter dokončali postopek rezervacije.
S klikom na gumb "V redu" boste potrdili zgoraj izbrani naslov za dostavo in dokončali postopek rezervacije.
Obvestilo
Trenutno je storitev za avtomatsko prijavo in rezervacijo nedostopna. Gradivo lahko rezervirate sami na portalu Biblos ali ponovno poskusite tukaj kasneje.
Gesla v Splošnem geslovniku COBISS
Izbira mesta prevzema
Gradivo iz matične enote je brezplačno. Če je gradivo na mesto prevzema dostavljeno iz drugih enot, lahko knjižnica to storitev zaračuna.
Mesto prevzema | Status gradiva | Rezervacija |
---|
Rezervacija v teku
Prosimo, počakajte trenutek.
Rezervacija je uspela.
Rezervacija ni uspela.
Rezervacija...
Članska izkaznica:
Mesto prevzema: