VSE knjižnice (vzajemna bibliografsko-kataložna baza podatkov COBIB.SI)
-
Application of a force model adapted for the precise turning of various metallic materialsHorváth, Richárd ; Lukács, JuditThe knowledge of cutting forces is critical. They might affect the load of the machine and, in the case of fine turning, the deformation of thin and slim workpieces. The generated forces depend not ... only on material properties (hardness, tensile strength) and on cutting parameters, but also on the tool edge geometry, that strongly determines the geometry of the chip (thickness and width). This article deals with the application of a force model adapted for precise turning technology. Three different types of materials widely used in mass production were taken into consideration (C45 and KO36 steel types and AS12 die-cast aluminium alloy). The components of cutting force were measured in three directions (Fc, Ff, Fp) and the specific cutting forces were calculated. The main values of specific cutting forces were introduced for precision turning (k1,0,1); using this, a new force model was constructed based on the theoretical parameters of the non-deformed chip cross-section (h eq is equivalent chip thickness and l eff effective length of the edge of the tool) in case of all three examined materials. Investigations revealed that the influence of l eff on specific cutting force components is not negligible; however, it has the least effect on k c and is the most influential in case of k p . The errors of the constructed new force models follow Gaussian distribution with low values of standard deviation. Thereby, the models can be applied to estimate cutting force components during the technological process planning procedure with adequate accuracy.Vir: Strojniški vestnik = Journal of mechanical engineering. - ISSN 0039-2480 (Vol. 63, no. 9, Sep. 2017, str. 489-500, SI 72)Vrsta gradiva - članek, sestavni delLeto - 2017Jezik - angleškiCOBISS.SI-ID - 15662107
vir: Strojniški vestnik = Journal of mechanical engineering. - ISSN 0039-2480 (Vol. 63, no. 9, Sep. 2017, str. 489-500, SI 72)
Vnos na polico
Trajna povezava
- URL:
Faktor vpliva
Dostop do baze podatkov JCR je dovoljen samo uporabnikom iz Slovenije. Vaš trenutni IP-naslov ni na seznamu dovoljenih za dostop, zato je potrebna avtentikacija z ustreznim računom AAI.
Leto | Faktor vpliva | Izdaja | Kategorija | Razvrstitev | ||||
---|---|---|---|---|---|---|---|---|
JCR | SNIP | JCR | SNIP | JCR | SNIP | JCR | SNIP |
Baze podatkov, v katerih je revija indeksirana
Ime baze podatkov | Področje | Leto |
---|
Povezave do osebnih bibliografij avtorjev | Povezave do podatkov o raziskovalcih v sistemu SICRIS |
---|---|
Horváth, Richárd | |
Lukács, Judit |
Vir: Osebne bibliografije
in: SICRIS
Izberite prevzemno mesto:
Prevzem gradiva po pošti
Naslov za dostavo:
Med podatki člana manjka naslov.
Storitev za pridobivanje naslova trenutno ni dostopna, prosimo, poskusite še enkrat.
S klikom na gumb "V redu" boste potrdili zgoraj izbrano prevzemno mesto in dokončali postopek rezervacije.
S klikom na gumb "V redu" boste potrdili zgoraj izbrano prevzemno mesto in naslov za dostavo ter dokončali postopek rezervacije.
S klikom na gumb "V redu" boste potrdili zgoraj izbrani naslov za dostavo in dokončali postopek rezervacije.
Obvestilo
Trenutno je storitev za avtomatsko prijavo in rezervacijo nedostopna. Gradivo lahko rezervirate sami na portalu Biblos ali ponovno poskusite tukaj kasneje.
Gesla v Splošnem geslovniku COBISS
Izbira mesta prevzema
Gradivo iz matične enote je brezplačno. Če je gradivo na mesto prevzema dostavljeno iz drugih enot, lahko knjižnica to storitev zaračuna.
Mesto prevzema | Status gradiva | Rezervacija |
---|
Rezervacija v teku
Prosimo, počakajte trenutek.
Rezervacija je uspela.
Rezervacija ni uspela.
Rezervacija...
Članska izkaznica:
Mesto prevzema: