VSE knjižnice (vzajemna bibliografsko-kataložna baza podatkov COBIB.SI)
-
Finite element analysis of notch depth and angle in notch shear cutting of stainless-steel sheetEmre Engin, KaanPiercing is a crucial process in the sheet metal forming industry, and the surface quality of the pierced part is an important parameter that defines the overall quality of the product. However, ... obtaining a good surface quality is a challenging task that depends on the effect of several process parameters and necessitates the use of non-conventional procedures. Notch shear cutting is a relatively new progressive approach in which the workpiece is indented with a notch form with a predefined notch angle and depth, and then the indented workpiece is subjected to conventional piercing. In this study, conventional piercing and notch shear cutting processes were experimentally performed on 1.4301 stainless steel sheet of 2 mm thickness. Then, finite element (FE) analyses were conducted utilizing Deform-2D software. After ensuring that the experimental and simulation works were consistent with each other, the FE analysis of notch shear cutting was carried out for three distinct notch depths (15 %, 30 %, and 60 % of the workpiece thickness) and six different notch angles (10º, 20º, 30º, 40º, 50º, and 60º). Investigations were performed on shear zone length distributions, which are direct indications of the surface quality on sheared workpieces, crack propagation angles, and required cutting loads. The best surface quality was obtained when the notch angle was set to 50º and the notch depth was set to 15 % of the workpiece thickness. It was also observed that notch angle and notch depth had a certain level of influence on required cutting load.Vir: Strojniški vestnik = Journal of mechanical engineering. - ISSN 0039-2480 (Vol. 69, no. 7/8, Jul./Aug. 2023, str. 326-338)Vrsta gradiva - članek, sestavni del ; neleposlovje za odrasleLeto - 2023Jezik - angleškiCOBISS.SI-ID - 159343363
vir: Strojniški vestnik = Journal of mechanical engineering. - ISSN 0039-2480 (Vol. 69, no. 7/8, Jul./Aug. 2023, str. 326-338)
Vnos na polico
Trajna povezava
- URL:
Faktor vpliva
Dostop do baze podatkov JCR je dovoljen samo uporabnikom iz Slovenije. Vaš trenutni IP-naslov ni na seznamu dovoljenih za dostop, zato je potrebna avtentikacija z ustreznim računom AAI.
Leto | Faktor vpliva | Izdaja | Kategorija | Razvrstitev | ||||
---|---|---|---|---|---|---|---|---|
JCR | SNIP | JCR | SNIP | JCR | SNIP | JCR | SNIP |
Baze podatkov, v katerih je revija indeksirana
Ime baze podatkov | Področje | Leto |
---|
Povezave do osebnih bibliografij avtorjev | Povezave do podatkov o raziskovalcih v sistemu SICRIS |
---|---|
Emre Engin, Kaan |
Vir: Osebne bibliografije
in: SICRIS
Izberite prevzemno mesto:
Prevzem gradiva po pošti
Naslov za dostavo:
Med podatki člana manjka naslov.
Storitev za pridobivanje naslova trenutno ni dostopna, prosimo, poskusite še enkrat.
S klikom na gumb "V redu" boste potrdili zgoraj izbrano prevzemno mesto in dokončali postopek rezervacije.
S klikom na gumb "V redu" boste potrdili zgoraj izbrano prevzemno mesto in naslov za dostavo ter dokončali postopek rezervacije.
S klikom na gumb "V redu" boste potrdili zgoraj izbrani naslov za dostavo in dokončali postopek rezervacije.
Obvestilo
Trenutno je storitev za avtomatsko prijavo in rezervacijo nedostopna. Gradivo lahko rezervirate sami na portalu Biblos ali ponovno poskusite tukaj kasneje.
Gesla v Splošnem geslovniku COBISS
Izbira mesta prevzema
Gradivo iz matične enote je brezplačno. Če je gradivo na mesto prevzema dostavljeno iz drugih enot, lahko knjižnica to storitev zaračuna.
Mesto prevzema | Status gradiva | Rezervacija |
---|
Rezervacija v teku
Prosimo, počakajte trenutek.
Rezervacija je uspela.
Rezervacija ni uspela.
Rezervacija...
Članska izkaznica:
Mesto prevzema: