VSE knjižnice (vzajemna bibliografsko-kataložna baza podatkov COBIB.SI)
-
Friction in linear orthogonal cutting of beech wood (Fagus sylvatica) considering ploughing effect forces due to cutting tool tip bluntnessMerhar, Miran ; Bučar, Bojan, 1961-2012The paper presents the calculation of the coefficient of friction between the cutting tool and the chip in case of linear orthogonal cutting in the direction of 90-0°. Beech wood was cut with HSS ... cutting-tool at the cutting speed of 0.03 m.s-1. Rake angles were 16, 22, 31 and 42°, and the depths of cut were 0.3, 0.25, 0.2, 0.15 and 0.1 mm. A type II chip according to Franz was formed at the angles of 16 and 22°, and a type I chip was formed at the angles of 31 and 42°. The force resulting from the ploughing effect due to cutting tool tip bluntness was subtracted from the forces measured perpendicularly to the direction of cutting Fy, while the force resulting from the ploughing effect and the fracture force for creation of new surfaces were subtracted from the forces measured in the direction of cutting Fx. The coefficient of friction at all rake angles and depths of cut, calculated from the difference of forces, was 0.46 on average with a standard deviation of 0.009. The model with subtracted forces resulting from the ploughing effect has proved to be correct; the calculated coefficient of friction at all rake angles and chip thicknesses is constant since the coefficient of friction has to be independent of the force magnitude, while in the literature found, the coefficient of friction varies with the chip thickness and rake angle.Vir: Wood research. - ISSN 1336-4561 (Vol. 58, no. 2, 2013, str. 319-328)Vrsta gradiva - članek, sestavni del ; neleposlovje za odrasleLeto - 2013Jezik - angleškiCOBISS.SI-ID - 2127241
![loading ... loading ...](themes/default/img/ajax-loading.gif)
Vnos na polico
Trajna povezava
- URL:
Faktor vpliva
Dostop do baze podatkov JCR je dovoljen samo uporabnikom iz Slovenije. Vaš trenutni IP-naslov ni na seznamu dovoljenih za dostop, zato je potrebna avtentikacija z ustreznim računom AAI.
Leto | Faktor vpliva | Izdaja | Kategorija | Razvrstitev | ||||
---|---|---|---|---|---|---|---|---|
JCR | SNIP | JCR | SNIP | JCR | SNIP | JCR | SNIP |
Baze podatkov, v katerih je revija indeksirana
Ime baze podatkov | Področje | Leto |
---|
Povezave do osebnih bibliografij avtorjev | Povezave do podatkov o raziskovalcih v sistemu SICRIS |
---|---|
Merhar, Miran | 22063 |
Bučar, Bojan, 1961-2012 | 01392 |
Vir: Osebne bibliografije
in: SICRIS
Izberite prevzemno mesto:
Prevzem gradiva po pošti
Naslov za dostavo:
Med podatki člana manjka naslov.
Storitev za pridobivanje naslova trenutno ni dostopna, prosimo, poskusite še enkrat.
S klikom na gumb "V redu" boste potrdili zgoraj izbrano prevzemno mesto in dokončali postopek rezervacije.
S klikom na gumb "V redu" boste potrdili zgoraj izbrano prevzemno mesto in naslov za dostavo ter dokončali postopek rezervacije.
S klikom na gumb "V redu" boste potrdili zgoraj izbrani naslov za dostavo in dokončali postopek rezervacije.
Obvestilo
Trenutno je storitev za avtomatsko prijavo in rezervacijo nedostopna. Gradivo lahko rezervirate sami na portalu Biblos ali ponovno poskusite tukaj kasneje.
Gesla v Splošnem geslovniku COBISS
Izbira mesta prevzema
Gradivo iz matične enote je brezplačno. Če je gradivo na mesto prevzema dostavljeno iz drugih enot, lahko knjižnica to storitev zaračuna.
Mesto prevzema | Status gradiva | Rezervacija |
---|
Rezervacija v teku
Prosimo, počakajte trenutek.
Rezervacija je uspela.
Rezervacija ni uspela.
Rezervacija...
Članska izkaznica:
Mesto prevzema: