Narodna in univerzitetna knjižnica, Ljubljana (NUK)
-
Influence of the precipitation temperature on the thrust force and torque in drilling an Al 2219-SiCp[sub] composite = Vpliv temperature izločevalnega žarjenja na potisno silo in navor pri vrtanju kompozita Al 2219-SiCGanesh, Radhakrishnan ; Chandrasekaran, KesavanThis paper aims at understanding the influence of the precipitation temperature on the drilling performance of an Al 2219-SiC composite. This type of composite is currently in use in aerospace ... industries. Drilling is the most frequently employed secondary machining owing to the requirements of the fabrication. This composite was subjected to the precipitation heat treatment, hence calling for a study of the precipitation-temperature effect on the machining performance. The composite was fabricated through the powder-metallurgy route. The drilling trials were conducted with a PCD drill of a 5 mm diameter and 118° point angle. The experiments were conducted with different spindle speeds of (500, 1000 and 1500) r/min and feed rates of (10, 15 and 20) mm/min. The thrust force and torque were the performance indicators. The influences of the mass fraction of reinforcement, the precipitation temperature, the feed rate and the spindle speed on the thrust force and torque during drilling were analyzed. It was observed that the drilling performance was influenced significantly by the feed rate followed by the precipitation temperature, the mass fraction and the particle size of reinforcement. The spindle speed did not influence much the machining performance.Vir: Materiali in tehnologije = Materials and technology. - ISSN 1580-2949 (Letn. 48, št. 4, jul.-aug. 2014, str. 563-569)Vrsta gradiva - članek, sestavni del ; neleposlovje za odrasleLeto - 2014Jezik - angleškiCOBISS.SI-ID - 1074602
vir: Materiali in tehnologije = Materials and technology. - ISSN 1580-2949 (Letn. 48, št. 4, jul.-aug. 2014, str. 563-569)
Vnos na polico
Trajna povezava
- URL:
Faktor vpliva
Dostop do baze podatkov JCR je dovoljen samo uporabnikom iz Slovenije. Vaš trenutni IP-naslov ni na seznamu dovoljenih za dostop, zato je potrebna avtentikacija z ustreznim računom AAI.
Leto | Faktor vpliva | Izdaja | Kategorija | Razvrstitev | ||||
---|---|---|---|---|---|---|---|---|
JCR | SNIP | JCR | SNIP | JCR | SNIP | JCR | SNIP |
Baze podatkov, v katerih je revija indeksirana
Ime baze podatkov | Področje | Leto |
---|
Povezave do osebnih bibliografij avtorjev | Povezave do podatkov o raziskovalcih v sistemu SICRIS |
---|---|
Ganesh, Radhakrishnan | |
Chandrasekaran, Kesavan |
Vir: Osebne bibliografije
in: SICRIS
Izberite prevzemno mesto:
Prevzem gradiva po pošti
Naslov za dostavo:
Med podatki člana manjka naslov.
Storitev za pridobivanje naslova trenutno ni dostopna, prosimo, poskusite še enkrat.
S klikom na gumb "V redu" boste potrdili zgoraj izbrano prevzemno mesto in dokončali postopek rezervacije.
S klikom na gumb "V redu" boste potrdili zgoraj izbrano prevzemno mesto in naslov za dostavo ter dokončali postopek rezervacije.
S klikom na gumb "V redu" boste potrdili zgoraj izbrani naslov za dostavo in dokončali postopek rezervacije.
Obvestilo
Trenutno je storitev za avtomatsko prijavo in rezervacijo nedostopna. Gradivo lahko rezervirate sami na portalu Biblos ali ponovno poskusite tukaj kasneje.
Gesla v Splošnem geslovniku COBISS
Izbira mesta prevzema
Gradivo iz matične enote je brezplačno. Če je gradivo na mesto prevzema dostavljeno iz drugih enot, lahko knjižnica to storitev zaračuna.
Mesto prevzema | Status gradiva | Rezervacija |
---|
Rezervacija v teku
Prosimo, počakajte trenutek.
Rezervacija je uspela.
Rezervacija ni uspela.
Rezervacija...
Članska izkaznica:
Mesto prevzema:
Naročanje gradiva za izposojo v čitalnice
Naročanje kopij člankov
Urnik dostave gradiva z oznako DS v signaturi