Narodna in univerzitetna knjižnica, Ljubljana (NUK)
-
Wear behaviour and cutting performance of surfaced inserts for wood machiningBendikiene, Regita ...Machining, in general, and wood machining, in particular, are complex to explain and many factors influence the process. Natural wood is a nonhomogeneous biological material, so each species of wood ... requires different machining conditions and tools. Understanding the properties of wood and choosing the proper cutting tools and machining parameters can improve the quality of wooden products, increase production efficiency, and improve machining. The objective of this study was to find the most suitable cutting tools for the machining of oak wood grown in Lithuania. This paper describes tests of two commercial cutting inserts made of high speed tool steel (CT01M-LA2 and 8X6FT) and two experimental inserts (EI) made by surfacing using a submerged arc welding (SAW) technique and a mixture of alloying elements spread on the surface under industrial flux. The results obtained from the milling tests demonstrated the suitability of the suggested surfaced inserts for machining oak wood. All tool wear parameters, such as cutting edge radius, edge recession, nose width, and cutting power, have been evaluated and compared. The cutting edge radius of EI after 3200 m of cutting length was ~ 5.00 %m, 3 to 4 times lower than the wear of standard tools; similarly, the edge recession of the surfaced inserts showed 2 to 3 times lower results. The results of this study indicate that the cutting power increases as the feed per cutter increases. These findings suggest that surfaced inserts can replace the commercial inserts used for wood machining.Vir: Strojniški vestnik = Journal of mechanical engineering. - ISSN 0039-2480 (Vol. 61, no. 7/8, Jul.-Aug. 2015, str. 459-464, SI 82)Vrsta gradiva - članek, sestavni delLeto - 2015Jezik - angleškiCOBISS.SI-ID - 14100763
Avtor
Bendikiene, Regita |
Keturakis, Gintaras |
Pilkaite, Tilmute |
Pupelis, Edmundas
Teme
rezkanje lesa |
navarjanje |
obraba robu |
obraba orodja |
hrast (les) |
SAW
vir: Strojniški vestnik = Journal of mechanical engineering. - ISSN 0039-2480 (Vol. 61, no. 7/8, Jul.-Aug. 2015, str. 459-464, SI 82)
Vnos na polico
Trajna povezava
- URL:
Faktor vpliva
Dostop do baze podatkov JCR je dovoljen samo uporabnikom iz Slovenije. Vaš trenutni IP-naslov ni na seznamu dovoljenih za dostop, zato je potrebna avtentikacija z ustreznim računom AAI.
Leto | Faktor vpliva | Izdaja | Kategorija | Razvrstitev | ||||
---|---|---|---|---|---|---|---|---|
JCR | SNIP | JCR | SNIP | JCR | SNIP | JCR | SNIP |
Baze podatkov, v katerih je revija indeksirana
Ime baze podatkov | Področje | Leto |
---|
Povezave do osebnih bibliografij avtorjev | Povezave do podatkov o raziskovalcih v sistemu SICRIS |
---|---|
Bendikiene, Regita | |
Keturakis, Gintaras | |
Pilkaite, Tilmute | |
Pupelis, Edmundas |
Vir: Osebne bibliografije
in: SICRIS
Izberite prevzemno mesto:
Prevzem gradiva po pošti
Naslov za dostavo:
Med podatki člana manjka naslov.
Storitev za pridobivanje naslova trenutno ni dostopna, prosimo, poskusite še enkrat.
S klikom na gumb "V redu" boste potrdili zgoraj izbrano prevzemno mesto in dokončali postopek rezervacije.
S klikom na gumb "V redu" boste potrdili zgoraj izbrano prevzemno mesto in naslov za dostavo ter dokončali postopek rezervacije.
S klikom na gumb "V redu" boste potrdili zgoraj izbrani naslov za dostavo in dokončali postopek rezervacije.
Obvestilo
Trenutno je storitev za avtomatsko prijavo in rezervacijo nedostopna. Gradivo lahko rezervirate sami na portalu Biblos ali ponovno poskusite tukaj kasneje.
Gesla v Splošnem geslovniku COBISS
Izbira mesta prevzema
Gradivo iz matične enote je brezplačno. Če je gradivo na mesto prevzema dostavljeno iz drugih enot, lahko knjižnica to storitev zaračuna.
Mesto prevzema | Status gradiva | Rezervacija |
---|
Rezervacija v teku
Prosimo, počakajte trenutek.
Rezervacija je uspela.
Rezervacija ni uspela.
Rezervacija...
Članska izkaznica:
Mesto prevzema:
Naročanje gradiva za izposojo v čitalnice
Naročanje kopij člankov
Urnik dostave gradiva z oznako DS v signaturi