Abstract
In the development of structural composites based on regenerated cellulose filaments, the physical and chemical interactions at the fibre-matrix interphase need to be fully understood. In ...the present study, continuous yarns and filaments of viscose (rayon) were treated with either polymeric diphenylmethane diisocyanate (pMDI) or a pMDI-based hardener for polyurethane resins. The effect of isocyanate treatment on mechanical yarn properties was evaluated in tensile tests. A significant decrease in tensile modulus, tensile force and elongation at break was found for treated samples. As revealed by size exclusion chromatography, isocyanate treatment resulted in a significantly reduced molecular weight of cellulose, presumably owing to hydrolytic cleavage caused by hydrochloric acid occurring as an impurity in pMDI. Yarn twist, fibre moisture content and, most significantly, the chemical composition of the isocyanate matrix were identified as critical process parameters strongly affecting the extent of reduction in mechanical performance. To cope with the problem of degradative reactions an additional step using calcium carbonate to trap hydrogen ions is proposed.
Cutinases have shown potential for hydrolysis of the recalcitrant synthetic polymer polyethylene terephthalate (PET). We have shown previously that the rate of this hydrolysis can be enhanced by the ...addition of hydrophobins, small fungal proteins that can alter the physicochemical properties of surfaces. Here we have investigated whether the PET-hydrolyzing activity of a bacterial cutinase from Thermobifida cellulosilytica (Thc_Cut1) would be further enhanced by fusion to one of three Trichoderma hydrophobins, i.e., the class II hydrophobins HFB4 and HFB7 and the pseudo-class I hydrophobin HFB9b. The fusion enzymes exhibited decreased kcat values on soluble substrates (p-nitrophenyl acetate and p-nitrophenyl butyrate) and strongly decreased the hydrophilicity of glass but caused only small changes in the hydrophobicity of PET. When the enzyme was fused to HFB4 or HFB7, the hydrolysis of PET was enhanced >16-fold over the level with the free enzyme, while a mixture of the enzyme and the hydrophobins led only to a 4-fold increase at most. Fusion with the non-class II hydrophobin HFB9b did not increase the rate of hydrolysis over that of the enzyme-hydrophobin mixture, but HFB9b performed best when PET was preincubated with the hydrophobins before enzyme treatment. The pattern of hydrolysis by the fusion enzymes differed from that of Thc_Cut1 as the concentration of the product mono(2-hydroxyethyl) terephthalate relative to that of the main product, terephthalic acid, increased. Small-angle X-ray scattering (SAXS) analysis revealed an increased scattering contrast of the fusion proteins over that of the free proteins, suggesting a change in conformation or enhanced protein aggregation. Our data show that the level of hydrolysis of PET by cutinase can be significantly increased by fusion to hydrophobins. The data further suggest that this likely involves binding of the hydrophobins to the cutinase and changes in the conformation of its active center.
In this study cutinases from Thermobifida cellulosilytica DSM44535 (Thc_Cut1 and Thc_Cut2) and Thermobifida fusca DSM44342 (Thf42_Cut1) hydrolyzing poly(ethylene terephthalate) (PET) were ...successfully cloned and expressed in E.coli BL21-Gold(DE3). Their ability to hydrolyze PET was compared with other enzymes hydrolyzing natural polyesters, including the PHA depolymerase (ePhaZmcl) from Pseudomonas fluorescens and two cutinases from T. fusca KW3. The three isolated Thermobifida cutinases are very similar (only a maximum of 18 amino acid differences) but yet had different kinetic parameters on soluble substrates. Their k cat and K m values on pNP–acetate were in the ranges 2.4–211.9 s–1 and 127–200 μM while on pNP–butyrate they showed k cat and K m values between 5.3 and 195.1 s–1 and between 1483 and 2133 μM. Thc_Cut1 released highest amounts of MHET and terephthalic acid from PET and bis(benzoyloxyethyl) terephthalate (3PET) with the highest concomitant increase in PET hydrophilicity as indicated by water contact angle (WCA) decreases. FTIR-ATR analysis revealed an increase in the crystallinity index A 1340/A 1410 upon enzyme treatment and an increase of the amount of carboxylic and hydroxylic was measured using derivatization with 2-(bromomethyl)naphthalene. Modeling the covalently bound tetrahedral intermediate consisting of cutinase and 3PET indicated that the active site His-209 is in the proximity of the O of the substrate thus allowing hydrolysis. On the other hand, the models indicated that regions of Thc_Cut1 and Thc_Cut2 which differed in electrostatic and in hydrophobic surface properties were able to reach/interact with PET which may explain their different hydrolysis efficiencies.
The polymer industry is under pressure to mitigate the environmental cost of petrol-based plastics. Biotechnologies contribute to the gradual replacement of petrol-based chemistry and the development ...of new renewable products, leading to the closure of carbon circle. An array of bio-based building blocks is already available on an industrial scale and is boosting the development of new generations of sustainable and functionally competitive polymers, such as polylactic acid (PLA). Biocatalysts add higher value to bio-based polymers by catalyzing not only their selective modification, but also their synthesis under mild and controlled conditions. The ultimate aim is the introduction of chemical functionalities on the surface of the polymer while retaining its bulk properties, thus enlarging the spectrum of advanced applications.
The present study investigated the effect of selected structural parameters on the mechanical performance of regenerated cellulose composites. The experimental setup comprised continuous viscose ...(rayon) yarns embedded in a matrix of epoxy resin. Mechanical and microscopic characterizations involved comparing the following: yarns consisting of untwisted filaments and twisted warp and weft yarns taken from a plain weave fabric, yarns with and without avivage (fiber finish), as well as yarns with and without an acrylic coating. During the epoxy treatment, samples were either prestressed or laid horizontally to preserve the original yarn structure. Tensile tests revealed that yarn crimp had a significant impact on the strength properties of composite specimens, a higher crimp ratio leading to a decrease in performance. Applying prestress to crimped yarns has proven to be an effective way to enable straight alignment in the loading direction, which is essential for the design of stiffness‐ and strength‐optimized yarn composites. Unlike an avivage, which did not markedly affect the mechanical properties of composite yarns, the application of an acrylic coating prior to resin impregnation was found to provide significantly increased extensibility and more ductile fracture behavior.
Enzyme-catalyzed hydrolysis of poly(ethylene terephthalate) using conventional and ultrasound energy (USe). The use of USe as heat source lead to an 6.6-fold increase of the released degradation ...products. Display omitted
•Ultrasound-enhanced cutinase activity towards PET hydrolysis is reported.•Ultrasonic activation is more effective when higher polymer surface is available.•A negative effect of polymer crystallinity on enzymatic hydrolysis was observed.
The application of ultrasound was found to enhance enzymatic hydrolysis of poly(ethylene terephthalate) (PET). After a short activation phase up to 6.6times increase in the amount of released products was found. PET powder with lower crystallinity of 8% was hydrolyzed faster when compared to PET with 28% crystallinity. Ultrasound activation was found to be around three times more effective on powders vs. films most likely due to a larger surface area accessible to the enzyme.
Summary
Due to the rising global environment protection awareness, recycling strategies that comply with the circular economy principles are needed. Polyesters are among the most used materials in ...the textile industry; therefore, achieving a complete poly(ethylene terephthalate) (PET) hydrolysis in an environmentally friendly way is a current challenge. In this work, a chemo‐enzymatic treatment was developed to recover the PET building blocks, namely terephthalic acid (TA) and ethylene glycol. To monitor the monomer and oligomer content in solid samples, a Fourier‐transformed Raman method was successfully developed. A shift of the free carboxylic groups (1632 cm−1) of TA into the deprotonated state (1604 and 1398 cm−1) was observed and bands at 1728 and 1398 cm−1 were used to assess purity of TA after the chemo‐enzymatic PET hydrolysis. The chemical treatment, performed under neutral conditions (T = 250 °C, P = 40 bar), led to conversion of PET into 85% TA and small oligomers. The latter were hydrolysed in a second step using the Humicola insolens cutinase (HiC) yielding 97% pure TA, therefore comparable with the commercial synthesis‐grade TA (98%).
A synergic chemo‐enzymatic depolymerization of poly(ethylene terephthalate) (PET) from textile waste was successfully carried out yielding 97% pure terephthalic acid that could be used for PET re‐synthesis.
PDF
