For the upgrade of its Inner Tracking System, the ALICE experiment plans to install a new tracker fully constructed with monolithic active pixel sensors implemented in a standard 180 nm CMOS imaging ...sensor process, with a deep pwell allowing full CMOS within the pixel. Reverse substrate bias increases the tolerance to non-ionizing energy loss (NIEL) well beyond 10131MeVneq∕cm2, but does not allow full depletion of the sensitive layer and hence full charge collection by drift, mandatory for more extreme radiation tolerance. This paper describes a process modification to fully deplete the epitaxial layer even with a small charge collection electrode. It uses a low dose blanket deep high energy n-type implant in the pixel array and does not require significant circuit or layout changes so that the same design can be fabricated both in the standard and modified process. When exposed to a 55Fe source at a reverse substrate bias of −6 V, pixels implemented in the standard and the modified process in a low and high dose variant for the deep n-type implant respectively yield a signal of about 115 mV, 110 mV and 90 mV at the output of a follower circuit. Signal rise times heavily affected by the speed of this circuit are 27.8+∕−5 ns, 23.2+∕−4.2 ns, and 22.2+∕−3.7 ns rms, respectively. In a different setup, the single pixel signal from a 90Sr source only degrades by less than 20% for the modified process after a 10151MeVneq∕cm2 irradiation, while the signal rise time only degrades by about 16+∕−2 ns to 19+∕−2.8 ns rms. From sensors implemented in the standard process no useful signal could be extracted after the same exposure. These first results indicate the process modification maintains low sensor capacitance, improves timing performance and increases NIEL tolerance by at least an order of magnitude.
The renewal of interest in Time of Flight Positron Emission Tomography (TOF-PET), as well as the necessity to precisely tag events in high energy physics (HEP) experiments at future colliders are ...pushing for an optimization of all factors affecting the time resolution of the whole acquisition chain comprising the crystal, the photo detector, and the electronics. The time resolution of a scintillator-based detection system is determined by the rate of photo electrons at the detection threshold, which depends on the time distribution of photons being converted in the photo detector. The possibility to achieve time resolution of about 100 ps Full Width at Half Maximum (FWHM) requires an optimization of the light production in the scintillator, the light transport and its transfer from the scintillator to the photo detector. In order to maximize the light yield, and in particular the density of photons in the first nanosecond, while minimizing the rise time and decay time, particular attention must be paid to the energy transfer mechanisms to the activator as well as to the energy transition type at the activator ion. Alternatively other light emission mechanisms can be considered. We show that particularly Cerenkov emission can be used for this purpose. Special emphasis was put on the light transport within the crystal and at its interface with the photo detector. Since light is produced isotropically in the scintillator the detector geometry must be optimized to decrease the optical path-length to the photo detector. Moreover light bouncing within the scintillator, affecting about 70% of the photons generated in currently used crystals, must be reduced as much as possible. We also investigate photonics crystals that are specifically designed to favor specific light propagation modes at the limit of total reflection inside and outside of the crystal and how they might increase the light transfer efficiency to the photo detector and hence improve time resolution. Examples for the production and deposition of photonics crystals as layers on Lutetium Yttrium Ortho-Silicate (LYSO) and Lutetium Yttrium Aluminum Perovskite (LuYAP) crystals are shown here, as well as first results on an improved light extraction resulting from this method.
Time of flight (TOF) measurements in positron emission tomography (PET) are very challenging in terms of timing performance, and should ideally achieve less than 100 ps FWHM precision. We present a ...time-based differential technique to read out silicon photomultipliers (SiPMs) which has less than 20 ps FWHM electronic jitter. The novel readout is a fast front end circuit (NINO) based on a first stage differential current mode amplifier with 20 Ω input resistance. Therefore the amplifier inputs are connected differentially to the SiPM's anode and cathode ports. The leading edge of the output signal provides the time information, while the trailing edge provides the energy information. Based on a Monte Carlo photon-generation model, HSPICE simulations were run with a 3 × 3 mm 2 SiPM-model, read out with a differential current amplifier. The results of these simulations are presented here and compared with experimental data obtained with a 3 × 3 × 15 mm 3 LSO crystal coupled to a SiPM. The measured time coincidence precision and the limitations in the overall timing accuracy are interpreted using Monte Carlo/SPICE simulation, Poisson statistics, and geometric effects of the crystal.
The MAPS foil Beolé, S.; Carnesecchi, F.; Contin, G. ...
Nuclear instruments & methods in physics research. Section A, Accelerators, spectrometers, detectors and associated equipment,
01/2023, Letnik:
1046, Številka:
C
Journal Article
Recenzirano
Odprti dostop
We present a method of embedding a Monolithic Active Pixel Sensor (MAPS) into a flexible printed circuit board (FPC) and its interconnection by means of through-hole copper plating. The resulting ...assembly, baptised “MAPS foil”, is a flexible, light, protected, and fully integrated detector module. By using widely available printed circuit board manufacturing techniques, the production of these devices can be scaled easily in size and volume, making it a compelling candidate for future large-scale applications.
A first series of prototypes that embed the ALPIDE chip has been produced, functionally tested, and shown to be working.
Developments in quantum technologies in the last decades have led to a wide range of applications, but have also resulted in numerous novel approaches to explore the low energy particle physics ...parameter space. The potential for applications of quantum technologies to high energy particle physics endeavors has however not yet been investigated to the same extent. In this paper, we propose a number of areas where specific approaches built on quantum systems such as low-dimensional systems (quantum dots, 2D atomic layers) or manipulations of ensembles of quantum systems (single atom or polyatomic systems in detectors or on detector surfaces) might lead to improved high energy particle physics detectors, specifically in the areas of calorimetry, tracking or timing.
The ALICE collaboration is currently developing a new vertex detector ("ITS3"), which is planned to be installed in 2026 - 2028 during LHC long shutdown 3 to replace the three innermost layers (Inner ...Barrel) of the current Inner Tracking System as from Run 4 onwards. ITS3 is based on a truly innovative concept, comprising the use of ultra-thin (50 micrometers) silicon wafers and stitching technologies in 65nm CMOS imaging process to produce large area (10cm x 26cm) Monolithic Active Pixels Sensors sensors which can be bent to half-cylindrical shapes of 18, 24 and 30 mm bending radii for layer 0, 1 and 2 respectively. The ITS3 will thus be built of six stitched sensors kept in place using slices of carbon foam. Together with a very low power consumption of about 20mV/cm2 allowing for air cooling, no further mechanical and electrical support structures are required, resulting in an extermely low material budget of less than 0.05\% of a radiation length per layer, providing extremely good tracking and vertexing capabilities.Within the comprehensive R\&D program for the ITS3 different analogue and digital test structures with various pixel pitch sizes, matrices and readout circuits have been produced and extensively tested in various particle beams before and after irradiation with TID and NIEL to validate the ITS3 technology approachIn this contribution we present an overview on the various prototypes and selected results on the detection performancve measurements in the laboratory and in test beams using various chip settings.
SiPM time resolution: From single photon to saturation Gundacker, S.; Auffray, E.; Di Vara, N. ...
Nuclear instruments & methods in physics research. Section A, Accelerators, spectrometers, detectors and associated equipment,
08/2013, Letnik:
718
Journal Article
Recenzirano
The time resolution of photon detection systems is important for a wide range of applications in physics and chemistry. It impacts the quality of time-resolved spectroscopy of ultrafast processes and ...has a direct influence on the best achievable time resolution of time-of-flight detectors in high-energy and medical physics. For the characterization of photon detectors, it is important to measure their exact timing properties in dependence of the photon flux and the operational parameters of the photodetector and its accompanying electronics. We report on the timing of silicon photomultipliers (SiPM) as a function of their bias voltage, electronics threshold settings and the number of impinging photons. We used ultrashort laser pulses at 400nm wavelength with pulse duration below 200fs. We focus our studies on different types of SiPMs (Hamamatsu MPPC S10931-025P, S10931-050P and S10931-100P) with different SPAD sizes (25μm, 50μm and 100μm) coupled to the ultrafast discriminator amplifier NINO. For the SiPMs, an optimum in the time resolution regarding bias and threshold settings can be reached. For the 50μm type, we achieve a single photon time resolution of 80ps sigma, and for saturating photon fluxes better than 10ps sigma.
Active Pixel Sensors used in High Energy Particle Physics require low power consumption to reduce the detector material budget, low integration time to reduce the possibilities of pile-up and fast ...readout to improve the detector data capability. To satisfy these requirements, a novel Address-Encoder and Reset-Decoder (AERD) asynchronous circuit for a fast readout of a pixel matrix has been developed. The AERD data-driven readout architecture operates the address encoding and reset decoding based on an arbitration tree, and allows us to readout only the hit pixels. Compared to the traditional readout structure of the rolling shutter scheme in Monolithic Active Pixel Sensors (MAPS), AERD can achieve a low readout time and a low power consumption especially for low hit occupancies. The readout is controlled at the chip periphery with a signal synchronous with the clock, allows a good digital and analogue signal separation in the matrix and a reduction of the power consumption. The AERD circuit has been implemented in the TowerJazz 180nm CMOS Imaging Sensor (CIS) process with full complementary CMOS logic in the pixel. It works at 10MHz with a matrix height of 15mm. The energy consumed to read out one pixel is around 72pJ. A scheme to boost the readout speed to 40MHz is also discussed. The sensor chip equipped with AERD has been produced and characterised. Test results including electrical beam measurement are presented.