The shaped charge jet formation of a Zr-based amorphous alloy and the applicability of different numerical algorithms to describe the jet formed were experimentally and numerically investigated. ...X-ray experiments were performed to study jet characteristics. The numerical results for the Zr-based amorphous alloy jet formed via the Euler and smooth particle hydrodynamics (SPH) algorithms were compared and analyzed using the Autodyn hydrocode. Particle motion was examined based on material properties. The Zr-based amorphous alloy formed a noncohesive jet driven by an 8701 explosive. Both the Euler and SPH algorithms achieved high accuracy for the determination of jet velocity. When the improved Johnson-Holmquist constitutive model (JH-2) was used, numerical results confirmed the model's suitability for the Zr-based amorphous alloy. The Euler algorithm effectively reflected jet shape within a short computing time, whereas the SPH algorithm was highly suitable for showing the shape of the jet tail within a long computing time. In the 3D Euler model, the flared jet mouth indicated radial particle dispersion; however, in the 2D model, particle dispersion in the head was directly observed by using the JH-2 material model. The brittle fracture of the material reduced the proportion of particles near the liner apex forming a jet. Furthermore, a new method in which stagnation pressure was used to predict jet formation and its coherence was proposed since the collapse angle was difficult to obtain.
The flow stress of face-centered cubic (FCC) metals exhibits a rapid increase near a strain rate of 104 s−1 under fixed-strain conditions. However, many existing constitutive models either fail to ...capture the mechanical characteristics of this plastic deformation or use piecewise strain-rate hardening models to describe this phenomenon. Unfortunately, these piecewise models may suffer from issues such as discontinuity of physical quantities and difficulties in determining segment markers, and struggle to reflect the underlying physical mechanisms that give rise to this mutation phenomenon. In light of this, this paper proposes that the abrupt change in flow stress sensitivity to strain rate in FCC metals can be attributed to microstructural evolution characteristics. To address this, a continuous semiempirical physical constitutive model for FCC metals is established based on the microstructural size evolution proposed by Molinari and Ravichandran and the dislocation motion slip mechanism. This model effectively describes the mutation behavior of strain-rate sensitivity under fixed strain, particularly evident in an annealed OFHC. The predicted results of the model across a wide range of strain rates (10−4–106 s−1) and temperatures (77–1096 K) demonstrate relative errors generally within ±10% of the experimental values. Furthermore, the model is compared with five other models, including the mechanical threshold stress (MTS), Nemat-Nasser–Li (NNL), Preston–Tonks–Wallace (PTW), Johnson–Cook (JC), and Molinari–Ravichandran (MR) models. A comprehensive illustration of errors reveals that the proposed model outperforms the other five models in describing the plastic deformation behavior of OFHC. The error results offer valuable insights for selecting appropriate models for engineering applications and provide significant contributions to the field.
•This paper verifies the applicability of BSMPM, GIMP, and CPDI in mesoscale simulating the SCJs.•BSMPM based on cubic and quartic splines is most suitable for mesoscale simulating, whose SCJs are in ...great continuity with little cavity and small surface roughness.•For SCJs material, the strain evolution is hierarchical and the particle trajectories can be classified as a laminar layer, transition layer, and turbulent layer from outer to the axis, consistent with the grain size evolution.
Shaped charge (SC) generates a fluid-like high-speed jet (SCJ) undergoing extremely large ductile stretching without fracture. It is a formidable challenge to accurately track and monitor the mesoscale deformation characteristics of materials using fluid simulation algorithms. To address this issue, the Material Point Method (MPM) is introduced as an efficient particle-based method that discretizes the continuum into Lagrangian particles moving through a fixed Eulerian grid. By possessing all material properties, these particles facilitate tracking throughout the deformation process and enable the implementation of history-dependent constitutive models. Regrettably, the utilization of MPM in the study of SCJ formation is restricted. The objective of this study is to assess the capability of 2D-axisymmetric MPMs in modeling SCJ formation and free flight at the mesoscale, thereby providing valuable guidelines for their application in SCJs. The MPMs employed in this study are based on the B-spline (BSMPM) and domain interpolations (generalized and convected particle domain interpolations in MPM). The numerical results indicate that BSMPM with cubic and quartic splines is the most suitable method for calculating SCJs due to its exceptional continuity and alignment with the experimental data. The mesoscale evolution of particles reveals that the material undergoes impact crushing and tensile tearing, transforming into a low-speed slug and a high-speed jet. The equivalent plastic strain (EPS) in SCJs exhibits a radial expansion from the exterior to the axis in a layered manner. Particles in the outer layer with a thickness of approximately 1/2 exhibit a 'laminar' distribution, while particles near the axis exhibit 'turbulent' distribution and undergo severe deformation. The hierarchical progression of EPS and particle motion traces provides insight into the underlying causes of mesoscale experimental phenomena, such as the axial elongation of voids in the SCJ slug and the radial distribution of the material in three concentric circles.
How to effectively reduce the damage of frequent accidental explosions and explosion attacks to existing walls is an important concern of the blast resistance field. In the present study, the ...influence of the foamed concrete (density 820 kg/m3, water-cement ratio 0.4) coating thickness on the blast resistance of a 120 mm RC (reinforced concrete) wall was studied through blast experiments, numerical simulations, and shock wave theory. Results show that the influences of foamed concrete on the blast resistance of RC walls are jointly decided by the stress drop caused by impedance effect and exponential attenuation and the stress rise caused by high-speed impact compression. The coating thickness mainly affects the foam concrete’s fragmentation degree and stress attenuation. A lower critical coating thickness exists in foamed concrete-coated RC walls. The blast resistance of the RC wall will decrease when the coating thickness is less than that value. The lower critical coating thickness is related to the intensity of blast load and the energy absorption capacity of foamed concrete, and it can be predicted by monitoring the explosive stress and energy incident to the RC wall.
Enhancing the blast resistance of building walls is a research hotspot in the field of anti-terrorism and explosion protection. In this study, numerical simulation and experimental verification were ...combined to analyze the failure phenomenon of brick masonry wall and sprayed polyurea-reinforced brick wall under contact explosion and determine the failure response parameters of the wall. The failure limit, mode, and mechanism of a 240 mm wall without reinforcement and strengthened with polyurea elastomer under different strength loads were investigated. Under contact explosion, the increase in the size of the blasting pit of the 240 mm wall gradually slowed down after the dose was increased to higher than 0.5 kg. Thereafter, the energy of the explosive load was released by splashing wall fragments as well as by deflecting and movement of the wall. The results show that the 240 mm walls sprayed with polyurea elastomer had outstanding anti-explosion performance because it wraps the damaged area and fragments of masonry wall inside the polyurea layer. When the thickness of the polyurea layer increases to 8 mm, the damaged area of the masonry wall decreases by 55.6% compared with that without reinforcement. The numerical simulation results were in good agreement with the experimental results.
Research on high-velocity bullet impact resistance of composite plates has been widely used in bulletproof material field, but limited studies have focused on the response of composite plate under ...low velocity and large fragment impact. In this paper, the impact response of polyurea-coated ceramic-aluminum composite plate to low velocity and large mass fragment was experimentally and numerically studied. The fragments were launched using a self-designed launcher, which can realize the free flip impact test of low velocity and large mass fragments with flight speed of 100–300 m/s and the mass of 0–100 g. Based on finite element method and smooth particle hydrodynamics, the impact model of low-velocity large fragments on composite plates was established to study fragment deformation and composite plate damage and compared with the experimental results to verify the effectiveness of the model. The multi-angle impact response of the fragment on the composite plate was studied. Results indicated that unlike the high-velocity impact of traditional bullets, low-velocity and large-mass fragments will flip in varying degrees after hitting the target accompanied by the deformation of the fragments, which remarkably influence the impact penetration ability of the fragments. Moreover, with the increase of biting angle, the composite plates show enhanced energy absorption capacity.
Display omitted
The effect of liquid parameters on the defense capability of the liquid-filled compartment structure (LFCS) of a shaped charge jet (SCJ) is quantified using dimension analysis of experiments on the ...reduced depth of SCJ penetration, which is disturbed via the LFCS with different liquids. The effects of three parameters, namely, liquid density, sound velocity and dynamic viscosity, on LFCS defense for SCJ are discussed quantitatively. Dynamic viscosity exerts the most important effect on LFCS disturbance of SCJ penetration, followed by liquid density. Meanwhile, sound velocity causes a negligible effect on LFCS disturbance of SCJ when the hole diameter in LFCSs are short. LFCSs offer excellent protection as they can significantly reduce the penetration capability of SCJ. Thus, LFCSs can be used as a new kind of armor for defense against SCJ.
In this study, electromagnetic interference testing of microcontroller units (MCUs) under different electromagnetic pulse (EMP) amplitudes, full width at half maximum (FWHM), and at different angles ...was carried out on an EMP cell. The coupling path of the radiation-type EMP experiment on the circuit board is random. However, in several experiments with two pins specific to a certain integrated circuit, by measuring the interference voltage of MCU pins, the statistical results indicate that as the pressure of the air gap switch of the power source increased, both the breakdown voltage and the electric field in the transverse electromagnetic (TEM) cell increased, resulting in higher electromagnetic interference (EMI) received by these two pins. As the capacitance of the storage capacitor increased, the EMI also increased. In addition, the results showed that the interference of EMP on the MCU had strong directionality; i.e., path selectivity, which was related to the structure of the MCU. X-ray imaging of the destroyed MCU showed that when the internal wiring direction of the pin is consistent with the propagation direction of the interference pulse, the EMI was minimal or even unnoticeable.
The process of liquid radial reflux interference during jet penetration in a liquid-filled composite structure is divided in this study into three stages: bottom plate reflection interference, ...side-wall reflection interference, and side-wall secondary reflection interference. The calculation model of the velocity interval of the disturbed jet and the residual penetration depth of the jet has been established through theoretical analysis. Results show that the liquid-filled composite structure can interfere with the high-speed section of the shaped charge jet. The accuracy of the theoretical analysis in this paper has been verified through numerical simulation, X-ray, and depth-of-penetration experiments. Among the results, those of the X-ray experiment show that the liquid-filled composite structure has interference on the tip of the shaped charge jet, which provides a possibility for the application of the liquid-filled composite structure to ammunition safety and other extreme cases.
A thermal environment has a complex influence on the dynamic characteristics of fiber-reinforced composite materials and structures. It is challenging to consider the effects of high temperature and ...external vibration energy simultaneously on their nonlinear vibration response. In this research, the material nonlinearities, due to both the excitation amplitudes and the high temperatures, are studied for the first time, and a new nonlinear vibration model of fiber-reinforced composite thin plates in a thermal environment is proposed by introducing the nonlinear thermal and amplitude fitting coefficients simultaneously. Then, based on the classical laminated plate theory, the complex modulus approach, and the power function and the Ritz methods, dynamic governing equations in high-temperature environments are derived to solve the nonlinear natural frequencies and vibration responses and damping parameters. Moreover, the three-dimensional fitting curves of the elastic moduli and loss factors, excitation amplitudes, and temperature values are obtained so that the key nonlinear fitting coefficients in the amplitude- and temperature-dependent model can be identified. To validate this model, the experimental tests on CF130 carbon/epoxy composite thin plates are undertaken. It is found that the 3rd and 5th natural frequencies, vibration responses, and damping results obtained from the nonlinear model are consistent with the experimental measurements, and the mechanism of nonlinear thermal vibration behaviour is revealed.
PDF
