3D printing has revolutionized the microfabrication prototyping workflow over the past few years. With the recent improvements in 3D printing technologies, highly complex microfluidic devices can be ...fabricated via single-step, rapid, and cost-effective protocols as a promising alternative to the time consuming, costly and sophisticated traditional cleanroom fabrication. Microfluidic devices have enabled a wide range of biochemical and clinical applications, such as cancer screening, micro-physiological system engineering, high-throughput drug testing, and point-of-care diagnostics. Using 3D printing fabrication technologies, alteration of the design features is significantly easier than traditional fabrication, enabling agile iterative design and facilitating rapid prototyping. This can make microfluidic technology more accessible to researchers in various fields and accelerates innovation in the field of microfluidics. Accordingly, this Special Issue seeks to showcase research papers, short communications, and review articles that focus on novel methodological developments in 3D printing and its use for various biochemical and biomedical applications.
An ideal artificial bone implant should have similar mechanical properties and biocompatibility to natural bone, as well as an internal structure that facilitates stomatal penetration. In this work, ...3D printing was used to fabricate and investigate artificial bone composites based on HA-ZrOsub.2-PVA. The composites were proportionally configured using zirconia (ZrOsub.2), hydroxyapatite (HA) and polyvinyl alcohol (PVA), where the ZrOsub.2 played a toughening role and PVA solution served as a binder. In order to obtain the optimal 3D printing process parameters for the composites, a theoretical model of the extrusion process of the composites was first established, followed by the optimization of various parameters including the spray head internal diameter, extrusion pressure, extrusion speed, and extrusion line width. The results showed that, at the optimum parameters of a spray head diameter of 0.2 mm, extrusion pressure values ranging from 1-3 bar, a line spacing of 0.8-1.5 mm, and a spray head displacement range of 8-10 mm/s, a better structure of biological bone scaffolds could be obtained. The mechanical tests performed on the scaffolds showed that the elastic modulus of the artificial bone scaffolds reached about 174 MPa, which fulfilled the biomechanical requirements of human bone. According to scanning electron microscope observation of the scaffold sample, the porosity of the scaffold sample was close to 65%, which can well promote the growth of chondrocytes and angiogenesis. In addition, c5.18 chondrocytes were used to verify the biocompatibility of the composite materials, and the cell proliferation was increased by 100% when compared with that of the control group. The results showed that the composite has good biocompatibility.
Popular media now often present 3D printing as a widely employed technology for the production of dental prostheses. This article aims to show, based on factual information, to what extent 3D ...printing can be used in dental laboratories and dental practices at present. It attempts to present a rational evaluation of todays´ applications of 3D printing technology in the context of dental restorations. In addition, the article discusses future perspectives and examines the ongoing viability of traditional dental laboratory services and manufacturing processes. It also shows which expertise is needed for the digital additive manufacturing of dental restorations.
Wire + arc additive manufacturing components contain significant residual stresses, which manifest in distortion. High-pressure rolling was applied to each layer of a linear Ti-6Al-4V wire + arc ...additive manufacturing component in between deposition passes. In rolled specimens, out-of-plane distortion was more than halved; a change in the deposits' geometry due to plastic deformation was observed and process repeatability was increased. The Contour method of residual stresses measurements showed that although the specimens still exhibited tensile stresses (up to 500 MPa), their magnitude was reduced by 60%, particularly at the interface between deposit and substrate. The results were validated with neutron diffraction measurements, which were in good agreement away from the baseplate.
This paper is part of a Themed Issue on Measurement, modelling and mitigation of residual stress.
This contribution studies failure by elastic buckling and plastic collapse during 3D concrete printing of wall structures. Four types of experiments were performed, which demonstrate the ...circumstances under which elastic buckling and plastic collapse occur, the effect of geometrical imperfections on the buckling response, the influence by the curing rate of the concrete material on the buckling stability, and the conditions leading to the successful printing of a complex, practical structure (a picnic table). The experimental results are compared to those computed by the parametric 3D printing model recently developed by Suiker (Int. J. Mech Sci, 137: 145–170, 2018), showing a very good agreement. The design formulas and design graphs deduced from the parametric model serve as a useful tool for accurately designing wall structures against failure during 3D concrete printing. Furthermore, they may be applied to optimize the process conditions during 3D printing, by providing the maximal printing velocity, the optimal geometrical characteristics, or the minimal amount of material required for adequately printing the structure.
•3D printing is a growing field with a broad range of clinical applications.•Quality of application via 3D printing is reliant on workflow optimization.•Benchmarks for 3D printing application have ...been outlined nationally.
Three-dimensional (3D) printing has applications in many fields and has gained substantial traction in medicine as a modality to transform two-dimensional scans into three-dimensional renderings. Patient-specific 3D printed models have direct patient care uses in surgical and procedural specialties, allowing for increased precision and accuracy in developing treatment plans and guiding surgeries. Medical applications include surgical planning, surgical guides, patient and trainee education, and implant fabrication. 3D printing workflow for a laboratory or clinical service that produces anatomic models and guides includes optimizing imaging acquisition and post-processing, segmenting the imaging, and printing the model. Quality assurance considerations include supervising medical imaging expert radiologists' guidance and self-implementing in-house quality control programs. The purpose of this review is to provide a workflow and guide for starting or optimizing laboratories and clinical services that 3D-print anatomic models or guides for clinical use.
We investigated the impact of CaCOsub.3 addition on the density and compressive strength of calcium aluminate cement (CAC)-based cementitious materials in binder jetting additive manufacturing ...(BJAM). To confirm the formation of a uniform powder bed, we examined the powder flowability and powder bed density for CaCOsub.3 contents ranging from 0 to 20 wt.%. Specifically, powders with avalanche angles between 40.1–45.6° formed a uniform powder bed density with a standard deviation within 1%. Thus, a 3D printing specimen (green body) fabricated via BJAM exhibited dimensional accuracy of less than 1% across the entire plane. Additionally, we measured the hydration characteristics of CAC and the changes in compressive strength over 30 days with the addition of CaCOsub.3. The results indicate that the addition of CaCOsub.3 to CAC-based cementitious materials forms multimodal powders that enhance the density of both the powder bed and the green body. Furthermore, CaCOsub.3 promotes the formation of highly crystalline monocarbonate (Csub.4AcHsub.11) and stable hydrate (Csub.3AHsub.6), effectively inhibiting the conversion of CAC and showing compressive strengths of up to 5.2 MPa. These findings suggest a strong potential for expanding the use of BJAM across various applications, including complex casting molds, cores, catalyst supports, and functional architectural interiors.
The significance of rheology in the context of bio three-dimensional (3D) printing lies in its impact on the printing behavior, which shapes material flow and the layer-by-layer stacking process. The ...objective of this study is to evaluate the rheological and printing behaviors of polycaprolactone (PCL) and dimethyl sulfone (DMSOsub.2) composites. The rheological properties were examined using a rotational rheometer, employing a frequency sweep test. Simultaneously, the printing behavior was investigated using a material extrusion 3D printer, encompassing varying printing temperatures and pressures. Across the temperature range of 120–140 °C, both PCL and PCL/DMSOsub.2 composites demonstrated liquid-like behavior, with a higher loss modulus than storage modulus. This behavior exhibited shear-thinning characteristics. The addition of DMSOsub.2 10, 20, and 30 wt% into the PCL matrix reduced a zero-shear viscosity of 33, 46, and 74% compared to PCL, respectively. The materials exhibited extrusion velocities spanning from 0.0850 to 6.58 mm/s, with velocity being governed by the reciprocal of viscosity. A significant alteration in viscosity by temperature change directly led to a pronounced fluctuation in extrusion velocity. Extrusion velocities below 0.21 mm/s led to the production of unstable printed lines. The presence of distinct viscosities altered extrusion velocity, flow rate, and strut diameter. This phenomenon allowed the categorization of pore shape into three zones: irregular, normal, and no-pore zones. It underscored the importance of comprehending the rheological aspects of biomaterials in enhancing the overall quality of bio-scaffolds during the 3D printing process.