Izolirana rekonstrukcija prednjeg križnog ligamenta (ACL) predstavlja zlatni standard u kirurškom liječenju rupture prednjeg križnog ligamenta. No, neuspjeh cijeljenja presatka i ostatna rotacijska ...nestabilnost koljena i dalje su česte postoperativne komplikacije. Anterolateralni ligament (ALL) i njegova uloga u kontroli rotacijske stabilnosti dobila je značajan interes 2013. nakon objave njegova „ponovnog otkrića”. Ta ligamentarna struktura, opisana još davne 1879., potječe od proksimalnog i stražnjeg dijela lateralnog epikondila bedrene kosti i hvata se na goljeničnoj kosti, na sredini između Gerdyjeva tuberkla i glavice fibule. Biomehanička ispitivanja pokazala su da anterolateralni ligament djeluje kao pasivni stabilizator koljena tijekom unutarnje rotacije koljena, i kod rupture ACL-a i lateralnih struktura koljena odgovoran je za nastanak pivot-shift fenomena. Pokazalo se da izolirana rekonstrukcija ACL-a u pacijenata s ozljedom ACL-a i ALL-a ne može vratiti normalnu kinematiku koljena, za razliku od njihove kombinirane rekonstrukcije. Uz to, dosadašnja literatura nudi brojne dokaze u smislu poboljšanja stabilnosti koljena nakon kombiniranog postupka rekonstrukcije ACL-a i ALL-a. Štoviše, nedavne kliničke studije pokazale su da ALL ima zaštitni učinak na očuvanje presatka ACL-a, kao i na brži ponovni povratak u sport i opće zadovoljstvo pacijenata s operativnim zahvatom. Ovaj pregledni rad ima za cilj dati pregled dosadašnjeg znanja anatomije, funkcije i učinka rekonstrukcije ACL-a i ALL-a u pacijenata s puknućem ACL-a.
Isolated anterior cruciate ligament (ACL) reconstruction is the gold standard in surgical treatment of anterior cruciate ligament rupture. However, graft failure rates and residual rotational instability of the knee are still common post-operative complications. The anterolateral ligament (ALL) and its role in controlling rotational stability gained considerable interest in 2013 following the announcement of its ‟rediscovery”. This ligamentous structure, described back in 1879, originates just proximal and posterior of the lateral epicondyle of the femur and it ends on the tibia, midway between Gerdy's tubercle and the head of the fibula. Biomechanical studies have shown that the anterolateral ligament acts as a passive knee stabilizer during internal knee rotation and in the rupture of the ACL and lateral knee structures is responsible for the presence of a pivot-shift knee phenomenon. It has been shown that isolated ACL reconstruction in patients with ACL and ALL injury cannot restore normal knee kinematics unlike their combined reconstruction. In addition, recent literature shows evidence in terms of improving knee stability after a combined ACL and ALL reconstruction procedure. Moreover, recent clinical studies have shown that ALL has a protective effect on the preservation of ACL graft as well as on the faster return to sport and overall patient satisfaction. This review aims to give an overview of our current knowledge of the anatomy, function, and effect of combined ACL and ALL reconstruction in patients with ACL rupture.
The constructions of three classical Greek problems (squaring the circle, doubling the cube and angle trisection) using only a ruler and a compass are considered unsolvable. The aim of this article ...is to explain the original methods of construction of the above-mentioned problems, which is something new in geometry. For the construction of squaring the circle and doubling the cube the Thales' theorem of proportional lengths has been used, whereas the angle trisection relies on a rotation of the unit circle in the Cartesian coordinate system and the axioms of angle measurement. The constructions are not related to the precise drawing figures in practice, but the intention is to find a theoretical solution, by using a ruler and a compass, under the assumption that the above mentioned instruments are perfectly precise. / Построение трех классических античных задач (квадратура круга, удвоение куба и трисекция угла), с помощью линейки и циркуля до сих пор считается неразрешимым. В данной статье представлены оригинальные методы построения вышеупомянутых задач, что представляет собой инновационный подход в геометрии. Для построения квадратуры круга и удвоения куба была использована теорема Фалеса о пропорциональных отрезках, а трисекция угла основанная на повороте единичного круга в декартовой системе координат и аксиомах измерения угла. Данные построения не претендуют на создание точных чертежей на практике, так как главная наша цель заключается в нахождении теоретического решения, основанного на построении данных фигур с помощью линейки и циркуля, с учетом предположения, что вышеупомянутые инструменты являются совершенно точными. / Konstrukcije tri klasična grčka problema (kvadratura kruga, udavajanje kocke i trisekcija ugla), uz upotrebu samo lenjira i šestara, do danas se smatraju nerešivim. Cilj ovog članka jeste da se originalnim metodama objasne konstrukcije pomenutih problema, što predstavlja novinu u geometriji. Za konstrukciju kvadrature kruga i udvajanje kocke korišćena je Talesova teorema o proporcionalnim dužima, a za trisekciju ugla rotacija jedinične kružnice u pravouglom koordinatnom sistemu i aksiome o mjerenju ugla. Konstukcije se ne odnose na precizno crtanje figura u praksi, već je namjera da se upotrebom lenjira i šestara nađe teorijsko rješenje pod pretpostavkom da su pomenuti instrumenti savršeno precizni.
Afino preslikavanje našlo je primjenu u različitim područjima geodezije. U ovome su radu opisane dvije moguće interpretacije afinog preslikavanja ravnine na ravninu. Pri prvoj od njih afino ...preslikavanje rastumačeno je kao kompozicija rotacije, nejednolike promjene mjerila i smicanja uz translaciju. Pokazano je da takva raščlamba afinog preslikavanja nije jedinstvena te je objašnjeno da pri interpretaciji afinog preslikavanja nema smisla govoriti o dvije translacije, dvije promjene mjerila ili dvije rotacije. Druga interpretacija afinog preslikavanja paralelno je projiciranje ravnine na ravninu u prostoru. Iz vektorskog prikaza preslikavanja dolazi se do uobičajenih izraza za afino preslikavanje s pomoću koordinata pridruženih točaka. Takav pristup omogućuje i jasnu geometrijsku interpretaciju parametara preslikavanja.
At each point of the geodetic network kinematic quantities are considered: normal strain, shear strain and rotation. This differs from the treatment of deformations on the basis of point movements as ...the traditional geodetic approach. Strain and rotation depend on the changes of geodetic datum. In the case of two different coordinate systems in each epoch, we cannot ca/cu/ate the real value of movements, strains and rotations. Despite the empirical studies of the datum invariance, we derived analytical mathematical expressions of functional dependency of strains and rotations from the relative change of datum parameters between two measurement epochs. Practical demonstration of functional dependencies has been shown in the case of the selected planar geodetic network.
Revizijski okvir svake zemlje članice EU trebao bi biti usklađen s Direktivom 2014/56/EU i Uredbom (EU) br. 537/2014 koja se odnosi na specifičnosti obavljanja zakonske revizije subjekata od javnog ...interesa. Države članice dužne su donijeti odgovarajuće odredbe za osiguravanje djelotvorne primjene Uredbe. U okviru Uredbe, državama članicama su dane brojne mogućnosti odabira opcija dostupnih za korištenje u njihovoj lokalnoj provedbi. Cilj istraživanja je napraviti komparativnu analizu između zemalja članica EU s obzirom na implementaciju opcija o posebnim zahtjevima revizije subjekata od javnog interesa iz Uredbe (EU) br. 537/2014 kako bi se utvrdile ključne razlike i sličnosti između zemalja članica EU, koristeći sljedeće kriterije usporedbe: definicija subjekata javnog interesa u zemljama članicama EU, rotacija revizora ili revizijskih društava te glavnih partnera, pružanje nerevizijskih usluga, struktura revizijskih naknada primljenih od subjekata javnog interesa te revizijsko izvještavanje. Koristeći znanstvenu metodu istraživanja za stolom, analiziran je revizijski okvir 28 zemalja članica EU i to za primjenu te iskorištene opcije o posebnim zahtjevima revizije subjekata od javnog interesa iz Uredbe (EU) br. 537/2014. Na temelju provedene analize revizijskog okvira zemalja članica EU, može se zaključiti da je transponiranje Uredbe rezultiralo regulatornim različitostima.
Rotacija revizijskih društava Perica, Ivana; Čular, Marko
Zbornik radova Ekonomskog fakulteta Sveučilišta u Mostaru,
01/2018
23
Journal Article
Odprti dostop
Problematika izbora revizora, tj. revizijskih društava aktualno je i otvoreno pitanje, kako s aspekta regulacije revizijske profesije tako i sa znanstvenog aspekta. Osnovno pitanje koje se pritom ...nameće je kakav učinak dužina trajanja revizijskog angažmana ima na kvalitetu provedene revizije. U većini slučajeva stvaraju se dobri odnosi između revizora i menadžmenta, zbog čega društva ne mijenjaju često svoje revizore. S jedne strane, takav dugoročni angažman može pridonijeti kvaliteti obavljene revizije jer su revizori u mogućnosti bolje upoznati i razumjeti poslovanje te financijske aspekte poslovanja društva. S druge strane, dužina trajanja revizijskog angažmana može biti povezana i s ugrožavanjem neovisnosti revizora te je zbog toga uvedena obveza rotacije revizora, a uskoro će primjenom Uredbe (EU) 537/2014 biti uvedena i obveza rotacije revizijskih društava. Cilj ovog istraživanja je analizirati koliko je prosječno trajanje revizijskog angažmana u Republici Hrvatskoj te utvrditi je li rotacija revizijskih društava povezana s vrstom revizijskog mišljenja, vrstom revizijskog društva te financijskim rezultatima poslovanja društva.
Istraživanje je provedeno na uzorku od 114 listanih društava u razdoblju od 2009. do 2014. godine. Dobiveni rezultati ukazuju da su rotacije revizijskih društava u Hrvatskoj još uvijek rijetke, odnosno da su listana društva sklonija razvijanju dugoročnih odnosa s revizijskim društvom. Nadalje, rezultati su pokazali da postoji razlika u rotaciji revizijskih društava, s obzirom na vrstu revizijskog mišljenja, a ne postoji, s obzirom na vrstu revizijskog društva, kao ni veza rotacije s financijskim rezultatima poslovanja revidiranog društva. Rezultati istraživanja mogli bi biti zanimljivi znanstvenicima, revizorima, revizijskim udruženjima, obveznicima revizije, regulatorima, kao i drugim zainteresiranim dionicima.
Provider: - Institution: - Data provided by Europeana Collections- The subject of this PhD Thesis is a very current subject due to intensive
progress in applying wind turbines around the world on one ...hand, and on the
other hand due to their sensitivity to atmospheric discharges and serious
consequences that can arise. Wind turbines are tall and nonstandard
constructions with rotating elements, usually installed in locations at which
the keraunic level is very high and grounding conditions are bad, and as
distributed sources of electrical energy they are more prone to lightning
stikes. The most prominent parts of the wind turbines, e.g. long blades and
nacelle are typically made of composite materials, which cannot successfully
withstand direct lightning strikes with currents up to 200 kA, neither
current disharge flow on their surface, during which a significant part of
this current at grounding has a path over or in vicinity of practically all
vital components of the wind turbine. Continuous development of protective
wind turbine systems for atmospheric discharges has a remarkable significance
in order to reduce negative consequences of mechanical damages of blades,
failure of electrical and electronic equipment and outage rate. Original
theoretical discussions, applying software numerical procedures and very
chalenging and financially demanding experimental testing enabled a high
quality analysis to be preformed in the PhD Thesis regarding direct
atmospheric discharges and to significally contribute to the subject. The
research conducted during work on this PhD Thesis are rather complex due to
nature of the events that are the subject of the research and non-standard
ways of testing and at the same time multidisciplinary because they involve a
good knowledge of the following fields: highvoltage technique, wind energy,
atmospheric discharge physics and lightning protection. In the first part of
this thesis the increasing significance that wind turbines have in
contemporary decentralized EES, an overview of actual state and standards
with regards to atmospheric discharges into wind turbines, and the specifics
of the methods of their lighting protections have been pointed out. The main
parts of the modern wind turbine are shown, because the wind turbine is a
very complex device, and special attention is paid to the analysis of
characteristics and means of protection of components through which the main
part of the discharge current flows. Different principles for protection of
composite materials from atmospheric discharges are discussed and
explanations on which types of composites can be used to construct wind
turbine blades and to what extent. An overview is given of the relevant
parameters and characteristics of direct atmospheric discharges, which
typically happen on wind turbine in service. The general principle of
lightning protection of wind turbines is discussed in the thesis, based on
determination of the necessary level of protection of electrical installation
for lightning protection. Four levels of protection are analyzed, and for
each of them criteria are defined which need to be meet by each element of
the lightning protection system. The testing of these criteria needs to
enable the probability of efficient work of protection is within predefined
limits which are characteristic for each level of protection. The proposed
procedures for calculating evaluation efficiency of lightning protection
installation of wind turbine and striking distance based on which the level
of protection of the protected wind turbine is uniquely determined. By using
an advanced electro-geometrical model, the numeric modeling and commercial
software, characteristic values of the striking distance (maximum distance
that the stepped leader can reach in its last jump) are researched and
possible lightning attachment points to the prominent parts of wind turbine
are estimated. Regarding the fact that there is no absolutely safe protection
from the direct lightning strike into a wind turbine which would be
cost-effective, the thesis discusses protection zones in which wind turbines
may be regarded protected from a direct lightning strike to a large extent.
The maximal level of risk for damaging wind turbines which could be tolerated
is also estimated, and it depends on the intensity of lightning discharges on
specific locations suitable for their construction. An estimate is made of
the expected number of years of work of wind turbines without damage during
direct atmospheric discharges for different applied methods of lightning
protection for blades, which is one of the important contributions of this
thesis. The main aim of the research is the estimate of danger for the wind
turbines to suffer from direct atmospheric discharges and the analysis of
specificity and functioning of different applied systems for lightning
protection. The analysis of discharge takes into account all relevant
electrical and meteorological parameters of lightning, and modeling of the
principles of protection takes into account different types of air
termination systems, down conductors and usage of isolating GFRP (glass fiber
reinforced plastic) and partially conducting CFC (carbon fibre composites)
composite material for construction of blades. Special attention is given to
analysis of physical phenomena during blade rotation, because the largest
number of attachment points was detected in the tops of long blades. Damaging
consequences and probability of direct atmospheric discharges into blades
regardless of the existing protection are researched. Characteristics and
response of specific elements of wind turbines are researched in the
conditions of load caused by direct atmospheric discharges, taking into
account the effects of protective devices for restricting surge. Possible
lightning attachment points are estimated on the blades of wind turbines of
full size and the consequences which could occur. In this thesis for the
first time in the world an attempt has been made to question whether there is
an influence of blade rotation (in the range of minimal to rated rotating
speed) to the incidence and characteristics of the atmospheric discharges in
the zone of air termination system on the tops of blades of wind turbines and
on the voltage waveform, which has not been studied systematically so far.
The method of physical modeling is applied, laboratory testing and an
original and detail theoretical analysis was made. Comparison of number of
strikes into stationary wind turbines with blades that are not moving with
regards to the ones in the standard working regime, within the same wind farm
during a long time period (10-15 years) is a possible way to determine in
real conditions the impact of rotation of blades of wind turbine to the
incidence of atmospheric discharge. However, this is very hard to accomplish
in practice. Also, the testing in laboratory conditions with rotating blades
of full size is practically impossible. Because of the named reasons, a
reduced-size wind turbine model was constructed and used for the purpose of
testing during work on this thesis. The basic expected results of the
research are development of methodology of the testing of efficiency of
lightning protection of wind turbines in the conditions of rotation of
blades, forming of physical model, advancements of the model of atmospheric
discharge and the choice of optimal method for determining the change of an
attractive effect. For that purpose an experimental determining of difference
was conducted in flashover impulse voltages between the specially shaped
arching electrode and blades of the reduced-size and specially constructed
model of wind turbine driven by a frequency controlled induction motor.
Lightning impulse voltages 1,2/50 μs are not quite suitable for experimenting
because of the short lasting of the front of the wave and characteristic
form. That is why the standard switching impulse voltage waveform 250/2500 μs
is applied to arching electrode as the most representative for simulating an
electrical field in vicinity of the wind turbine and which allows for
sufficient time for development of initiated leader and corresponding
streamers. Special arching electrode, onto which through the voltage devider
an impulse generator was connected, has a role of equivalent source of
electric field, which simulates a strike on top of stepped leader before the
last jump and without the current position of the blades having no influence
on the size of the distance between electrodes. Before the start of measuring
the estimated value of the voltage amplitude sufficient to get a flashover
was estimated. The model of wind turbine is completely the same as the
original, only with reduced size and without electrical generator. The thesis
gives a review of the measuring schemes with the appropriate equipment and
research procedures and also measuring techniques are described. This way of
high voltage testing is completely new in the world and has not been done so
far. During the testing on the model a comparison and comparative analysis
were done of the efficiency of applied various methods of lightning
protection of the blades of wind turbine (applying grounded conductive caps
on the ends of blades made of insulating materials, usage of
electrodesreceptors in the shape of knobs in vicinity of the tops of blades
and testing of blades without installed protective systems). Based on
similarity theory, characteristics of direct atmospheric discharges are
determined for the following typical speeds of blade rotation: w = 0 r/min
(when wind turbine is not rotating), w = 250 r/min (for winds of moderate
strength), and w = 400 r/min (rated rotor speed). As a criterion a 50%
flashover impulse switching voltage is used, determined by an up-and-down
method for blades that are still and that are rotating within the mentioned
speeds, for applied various methods of lightning protection.
U radu je primijenjen deformacijski pristup za razvoj sektorskog ravninskog konačnog elementa definiranog u polarnom koordinatnom sustavu. Element se koristi za određivanje ravninskog stanja u ...području elastičnosti. Razvijeni element ima tri stupnja slobode u svakom čvoru. Ponašanje ovog elementa ispitano je kroz analizu debelih cijevi izloženih unutarnjem tlaku i promjeni temperature. Utvrđena je efikasnost elementa i pokazano je da se primjenom ovog elementa postiže brža konvergencija rješenja pri izračunavanju naprezanja i pomaka nego u slučaju primjene drugih elemenata.
Prikazane su polu-analitičke metode za analizu vibracija torusnih ljuski izloženih tlaku, koje rotiraju oko svoje osi simetrije. Ovisnost deformacija rastezanja i savijanja o pomacima ljuske izvedena ...je iz općih izraza za rotacijske ljuske. Izrazi za deformacijsku (potencijalnu) i kinetičku energiju izvedeni su za rotirajući polarni koordinatni sustav. Potencijalna energija je najprije formulirana za slučaj velikih deformacija, a zatim je rastavljena na linearni i nelinearni dio, koji je zatim lineariziran. Korištena je nelinearna Green-Lagrangeova formulacija. Kinetička energija osim vibracijske komponente uključuje centrifugalni i Coriolisov dio. Za promjenu pomaka u, v i w u cirkularnom smjeru postavljeni su točni harmonijski izrazi. Pomaci u meridijalnom smjeru su pretpostavljeni u obliku Fourierovih redova. Korištena je Rayleigh-Ritzova metoda za minimiziranje ukupne energije. To je rezultiralo općom matricom krutosti, geometrijskom matricom krutosti uslijed prednaprezanja, te trima matricama masa vezanim za kvadrat prirodne frekvencije, umnožak prirodne frekvencije i brzine vrtnje, te kvadrat brzine vrtnje. Primjena razvijenog postupka ilustrirana je na primjeru zatvorene i otvorene torusne ljuske i tankostijenog torusnog prstena. Dobiveni rezultati (prirodne frekvencije i oblici vibriranja) uspoređeni su s rezultatima dobivenim metodom konačnih elemenata i uočeno je dobro podudaranje. Prednost prikazanog postupka je u znatno skraćenom vremenu obrade problema na računalu. U nastavku je razvijena metoda vrpčastih elemenata za analizu istih problema.Za deformacijsku i kinetičku energiju korišteni su ranije postavljeni izrazi u okviru Rayleigh-Ritzove metode. Ljuska je u meridijalnom smjeru modelirana nizom dvočvornih vrpčastih elemenata. Promjena pomaka u, v i w u meridijalnom smjeru unutar svakog elementa aproksimirana je štapnim i grednim funkcijama oblika. Minimiziranjem ukupne energije vrpčastog elementa formirane su matrice krutosti i matrice masa. U svrhu ubrzanja konvergencije rješenja razvijen je vrpčasti element višeg reda s tri čvora. Prikazanom metodom riješen je problem zatvorene torusne ljuske. Dobiveni rezultati uspoređeni su s rezultatima Rayleigh- Ritzove metode i metode konačnih elemenata. Nadalje, razmatrane su fleksijske i torzijske vibracije rotirajućeg prstena. Fleksijske vibracije se sprežu sa rasteznim vibracijama, a torzijske sa savojnim vibracijama. Odgovarajuće jednadžbe gibanja izvedene su iz teorije vibracija torusne ljuske. U prvom slučaju prsten je promatran kao vršni segment torusne ljuske, a u drugom slučaju kao bočni segment. Pokazano je da rotacija prstena dovodi do bifurkacije fleksijskih prirodnih frekvencija, a ne i torzijskih frekvencija. Teorija vibracija prstena ocjenjena je usporedbom rezultata analize vibracija jednog prstena s rezultatima metode konačnih elemenata i metode vrpčastih elemenata, te izmjerenim vrijednostima dostupnim u literaturi.
U radu se razmatraju neka fizička svojstva planeta na temelju izračunatog omjera njihove gravitacijske i centrifugalne sile. Iz tog omjera je određen matematički uvjet za stabilnost planeta. ...Uspoređivanjem perioda rotacije svakog planeta Sunčeva sustava s kritičnim periodom rotacije donosi se zaključak o njihovoj stabilnosti te se postavljaju nove hipoteze koje bi trebalo dalje istražiti.