Similar to calcium phosphates, magnesium phosphate (MgP) ceramics have been shown to be biocompatible and support favorable conditions for bone cells. Micropores below 25μm (MgP25), between 25 and ...53μm (MgP53), or no micropores (MgP0) were introduced into MgP scaffolds using different sizes of an NaCl template. The porosities of MgP25 and MgP53 were found to be higher than that of MgP0 because of their micro-sized pores. Both in vitro and in vivo analysis showed that MgP scaffolds with high porosity promoted rapid biodegradation. Implantation of the MgP0, MgP25, and MgP53 scaffolds into rabbit calvarial defects (with 4- and 6-mm diameters) was assessed at two times points (4 and 8weeks), followed by analysis of bone regeneration. The micro-CT and histologic analyses of the 4-mm defect showed that the MgP25 and MgP53 scaffolds were degraded completely at 4weeks with simultaneous bone and marrow-like structure regeneration. For the 6-mm defect, a similar pattern of regeneration was observed. These results indicate that the rate of degradation is associated with bone regeneration. The MgP25 and MgP53 scaffold-implanted bone showed a better lamellar structure and enhanced calcification compared to the MgP0 scaffold because of their porosity and degradation rate. Tartrate-resistant acid phosphatase (TRAP) staining indicated that the newly formed bone was undergoing maturation and remodeling. Overall, these data suggest that the pore architecture of MgP ceramic scaffolds greatly influence bone formation and remodeling activities and thus should be considered in the design of new scaffolds for long-term bone tissue regeneration.
The pore structural conditions of scaffold, including porosity, pore size, pore morphology, and pore interconnectivity affect cell ingrowth, mechanical properties and biodegradabilities, which are key components of scaffold in bone tissue regeneration. In this study, we designed hierarchical pore structure of the magnesium phosphate (MgP) scaffold by combination of the 3D printing process, self-setting reaction and salt-leaching technique, and first studied the effect of pore structures of bioceramic scaffolds on bone tissue regeneration through both in vitro and in vivo studies (rabbit calvarial model). The MgP scaffolds with higher porosity promoted more rapid biodegradation and enhanced new bone formation and remodeling activities at the same time.
•A strain based finite element ductile tearing simulation model for combined tensile and shear mode.•Strain based damage model parameters for tensile mode determined by smooth bar tensile test and ...fracture toughness test data.•Strain based damage model parameters for shear mode determined by smooth bar torsion test and torsion fracture test data.•Two different interactions rules (linear and parabolic) for combined tensile and shear mode damage.•Good comparison with circumferential surface cracked pipe test data when the linear interaction rule is used.
This paper proposes a strain-based damage model to simulate ductile tearing under combined tensile and shear modes. For tensile mode, the multiaxial fracture strain model depending only on the stress triaxiality is used, determined by analysing smooth bar tensile test and fracture toughness test data. For shear mode, a simple constant fracture strain model is used, determined by analysing smooth bar torsion test and torsion fracture test using a deep surface cracked cylinder specimen. The proposed damage model is applied to simulate circumferential surface cracked pipe made of SUS 304 under combined bending and torsion. Comparison with full-scale surface cracked pipe test data suggests that the use of the combined tensile and shear damage model with the linear interaction rule gives good and conservative prediction results.
The manganese (Mn) ion has recently been probed as a potential candidate element for the surface chemistry modification of titanium (Ti) implants in order to develop a more osteogenic surface with ...the expectation of taking advantage of its strong binding affinity to the integrins on bone-forming cells. However, the exact mechanism of how Mn enhances osteogenesis when introduced into the surface of Ti implants is not clearly understood. This study investigated the corrosion resistance and potential osteogenic capacity of a Mn-incorporated Ti surface as determined by electrochemical measurement and examining the behaviors of human mesenchymal stem cells (MSCs) in a clinically available sandblasted/acid-etched (SLA) oral implant surface intended for future biomedical applications. The surface that resulted from wet chemical treatment exhibited the formation of a Mn-containing nanostructured TiO2 anatase thin film in the SLA implant and improved corrosion resistance. The Mn-incorporated SLA surface displayed sustained Mn ion release and enhanced osteogenesis-related MSC function, which enhanced early cellular events such as spreading, focal adhesion, and mRNA expression of critical adhesion-related genes and promoted full human MSC differentiation into mature osteoblasts. Our findings indicate that surface Mn modification by wet chemical treatment is an effective approach to produce a Ti implant surface with increased osteogenic capacity through the promotion of the osteogenic differentiation of MSCs. The improved corrosion resistance of the resultant surface is yet another important benefit of being able to provide favorable osseointegration interface stability with an increased barrier effect.
To understand the role of endoplasmic reticulum (ER)‐stress in mice molar development, we studied Tmbim6 that antagonizes the unfolded protein response, using Tmbim6 knockout (KO) mice and in vitro ...organ cultivation with knocking down using small interfering RNA. During molar development, Tmbim6 is expressed in developing tooth at E14–E16, postnatal0 (PN0), and PN6. Mineral content in Tmbim6 KO enamel was reduced while dentin was slightly increased revealing ultrastructural changes in pattern formation of both enamel and dentin. Moreover, odontoblast differentiation was altered with increased Dspp expression at PN0 followed by altered AMELX localizations at PN5. These results were confirmed by in vitro organ cultivation and showed altered Bmp signaling, proliferation, and actin rearrangement in the presumptive ameloblast and odontoblasts that followed the altered expression of differentiation and ER stress‐related signaling molecules at E16.5. Overall, ER stress modulated by Tmbim6 would play important roles in patterned dental hard tissue formation in mice molar within a limited period of development.
Tmbim6 is involved in regulating endoplasmic reticulum (ER)‐stress. It plays an important role in the formation of patterned dental hard tissue in mice molar via modulation of ER stress in developing tooth.
Demineralized dentin matrix (DDM)-based materials have been actively developed and are well-known for their excellent performance in dental tissue regeneration. However, DDM-based bio-ink suitable ...for fabrication of engineered dental tissues that are patient-specific in terms of shape and size, has not yet been developed. In this study, we developed a DDM particle-based bio-ink (DDMp bio-ink) with enhanced three-dimensional (3D) printability. The bio-ink was prepared by mixing DDM particles and a fibrinogen-gelatin mixture homogeneously. The effects of DDMp concentration on the 3D printability of the bio-ink and dental cell compatibility were investigated. As the DDMp concentration increased, the viscosity and shear thinning behavior of the bio-ink improved gradually, which led to the improvement of the ink's 3D printability. The higher the DDMp content, the better were the printing resolution and stacking ability of the 3D printing. The printable minimum line width of 10%
/
DDMp bio-ink was approximately 252 μm, whereas the fibrinogen-gelatin mixture was approximately 363 μm. The ink's cytocompatibility test with dental pulp stem cells (DPSCs) exhibited greater than 95% cell viability. In addition, as the DDMp concentration increased, odontogenic differentiation of DPSCs was significantly enhanced. Finally, we demonstrated that cellular constructs with 3D patient-specific shapes and clinically relevant sizes could be fabricated through co-printing of polycaprolactone and DPSC-laden DDMp bio-ink.
Cold plasma processing has emerged a promising green technology with great potential to improve the quality and microbial safety of various minimally processed foods and materials. However, studies ...on non-thermal plasma-induced chemical interactions between major food ingredients that might change chemical structure and biological properties are very sparse. Thus, the objective of this study was to evaluate the influence of a dielectric barrier discharge (DBD) treatment on principal trans-resveratrol (TR) in several food stuffs by spectroscopic (HPLC, NMR, MS) and biological analyses. TR was dissolved in methanol and directly exposed to atmospheric non-thermal plasma field at 250 W for different durations (10, 20, 40, and 60 min), 40% relative humidity, and 25 °C. TR treated with plasma for 40 min showed greatly enhanced inhibitory activities for α-glucosidase and α-amylase than parent TR. Newly generated unusual compounds (1, 2) and known compounds (3–6) from plasma treated TR for 40 min were characterized using chromatographic and spectroscopic methods. The predominant reaction of TR induced by cold plasma followed by typical dimerization of products included methylene bridge formation and cyclization of TR. Among predominantly generated products, new compounds 1 and 2 showed more potent α-glucosidase and α-amylase inhibition capacities than parent TR. These results might be used to modify structures and enhance biological property of TR during food processing using DBD plasma treatment.
Display omitted
•Dimerization of trans-resveratrol was accelerated in methanol solution induced by plasma.•The structures of newly generated compounds from trans-resveratrol were elucidated by extensive spectroscopic interpretation.•Newly generated trans-resveratrol dimers can contribute to the enhancement of anti-diabetic properties.•Quantitative HPLC analysis of newly generated unique trans-resveratrol dimers was conducted.
•The effect of two options to determine parameters of a strain-based damage model on ductile tearing simulation is presented.•In the first option, smooth and notched bar tensile test data are used to ...determine the parameters.•In the second option, only smooth bar tensile data are used to determine the parameters.•Simulation results agree better with experimental data using the second option.•The use of the second option would offer advantages in terms of both accuracy and practicality.
This technical note presents the effect of two options to determine model parameters of a strain-based damage model on ductile tearing simulation. Notched bar tensile test data are used to determine the parameters in the first option, whereas only smooth bar tensile data are needed in the second one. In this investigation, four material data are considered. By comparing the simulation results with experimental data, it can be shown that it is difficult to simulate both crack initiation and crack growth well using the first option. However, with the second option, good agreement can be achieved in the prediction of both crack initiation and crack growth in all cases. A possible reason for overestimating crack growth using the first option is discussed.
This paper presents approximate in-depth residual stress and plastic strain profiles for laser-peened alloy 600 surface via FE analysis. In approximations, effects of the initial welding residual ...stress and the number of shots are quantified. Based on FE analysis results, residual stress profiles are quantified by two variables; the maximum difference in stress before and after LSP, and the depth up to which the compressive residual stress exists. Plastic strain profiles are quantified by one variable, the maximum equivalent plastic strain at the surface. The proposed profiles are validated by comparing with published LSP experimental results for welded plates. Effects of the initial welding residual stress and the number of shots on these variables are discussed. The proposed profile can be directly applied to predict the mitigation effect of LSP on PWSCC and to efficiently perform structural integrity assessment of laser peened nuclear components.
Alveolar bone loss, the major feature of periodontitis, results from the activation of osteoclasts, which can consequently cause teeth to become loose and fall out; the development of drugs capable ...of suppressing excessive osteoclast differentiation and function is beneficial for periodontal disease patients. Given the difficulties associated with drug discovery, drug repurposing is an efficient approach for identifying alternative uses of commercially available compounds. Here, we examined the effects of PF-3845, a selective fatty acid amide hydrolase (FAAH) inhibitor, on receptor activator of nuclear factor kappa B ligand (RANKL)-mediated osteoclastogenesis, its function, and the therapeutic potential for the treatment of alveolar bone destruction in experimental periodontitis. PF-3845 significantly suppressed osteoclast differentiation and decreased the induction of nuclear factor of activated T-cells cytoplasmic 1 (NFATc1) and the expression of osteoclast-specific markers. Actin ring formation and osteoclastic bone resorption were also reduced by PF-3845, and the anti-osteoclastogenic and anti-resorptive activities were mediated by the suppression of phosphorylation of rapidly accelerated fibrosarcoma (RAF), mitogen-activated protein kinase (MEK), extracellular signal-regulated kinase, (ERK) and nuclear factor κB (NF-κB) inhibitor (IκBα). Furthermore, the administration of PF-3845 decreased the number of osteoclasts and the amount of alveolar bone destruction caused by ligature placement in experimental periodontitis in vivo. The present study provides evidence that PF-3845 is able to suppress osteoclastogenesis and prevent alveolar bone loss, and may give new insights into its role as a treatment for osteoclast-related diseases.
This paper presents the finite element deformation and failure simulation of a typical Korean high-power reactor vessel under a severe accident characterized by large break loss of coolant (LBLOCA) ...with in-vessel retention of molten corium through external reactor vessel cooling (IVR-ERVC) conditions. Temperature distributions calculated using Modular Accident Analysis Program Version 5 (MAAP5) as thermal boundary conditions were used, and ABAQUS thermal and structural analyses were performed. After full ablation, the temperature of the inner surface in the thinnest section remained high (920 °C), but the stress remained relatively low (less than 6 MPa). At the outer surface, the stress was as high as 250 MPa; however, the resulting plastic strain was small owing to the low temperature of 200 °C. Variations in stress, inelastic strain, and temperature with time in the thinnest section suggest that the plastic and creep strains are saturated owing to stress relaxation, resulting in low cumulative damage. Thus, the lower head of the vessel can maintain its structural integrity under LBLOCA with IVR-ERVC conditions. The sensitivity analysis of internal pressure indicates the occurrence of failure in the thinnest section at an internal pressure >9.6 MPa via local necking followed by failure due to high stresses.