We investigate the possible origins of the reactor antineutrino anomalies in norm and shape within the framework of a summation model where β^{-} transitions are simulated by a phenomenological model ...of Gamow-Teller decay strength. The general trends of divergence from the Huber-Mueller model on the antineutrino side can be reproduced in both norm and shape. From the exact electron-antineutrino correspondence of the summation model, we predict similar distortions in the electron spectra, suggesting that biases on the reference spectra of fission electrons could be the cause of the anomalies.
The NUCLEUS experiment aims at measuring the coherent elastic scattering of nuclear reactor antineutrinos off nuclei using cryogenic calorimeters. Operating at an overburden of 3 m.w.e., muon-induced ...backgrounds are expected to be dominant. It is therefore essential to develop an efficient muon veto, with a detection efficiency of more than 99 %. This will be realized in NUCLEUS through a compact cube assembly of plastic scintillator panels. In order to prevent a large unshielded area where the cryostat intersects the shielding arrangement without unnecessarily increasing the induced detector dead time, a novel concept has been investigated, featuring a plastic scintillator-based active muon veto operating inside the NUCLEUS cryostat at sub-Kelvin temperatures. The verification of the key physical aspects of this cryogenic muon veto detector led to the first reported measurements of organic plastic scintillators at sub-Kelvin temperatures. The functionality of the principal scintillation process of organic plastic scintillators at these temperatures has been confirmed. On the basis of these findings, a disk-shape plastic scintillator equipped with wavelength shifting fibers and a silicon photomultiplier to guide and detect the scintillation light has been developed. The NUCLEUS cryogenic muon veto will be the first of its kind to be operated at sub-Kelvin temperatures.
Aluminum and gold nanowires were fabricated using 100 mm stencil wafers containing nanoslits fabricated with a focused ion beam. The stencils were aligned and the nanowires deposited on a substrate ...with predefined electrical pads. The morphology and resistivity of the wires were studied. Nanowires down to 70 nm wide and 5 μm long have been achieved showing a resistivity of 10 μΩcm for Al and 5 μΩcm for Au and maximum current density of ∼108 A/cm2. This proves the capability of stencil lithography for the fabrication of metallic nanowires on a full wafer scale.
The paper presents experimental research regarding the application of specific low melting metals in the FDM process. Previous trends in the transfer of the filament from the spool to the hot-end ...showed that the filament undergoes specific mechanical stress during the transfer. To achieve an appropriate transfer the filament should prove stiffness and resistance to the mechanical actions of the transfer wheels. At the same time, the entrance to the hot-end creates specific resistance to the movement of the filament, and the filament undergoes important deformations. The experimental research used three materials characterized by melting temperature below 260oC: Sn-58Bi, Sn-9Zn, and Sn-3.5Ag. Sn-58Bi showed a yield stress above 50 MPa, but very low extension during the tensile test. Sn-9Zn exhibited a yield stress above 30 MPa, and about double the extension during the tensile test. Sn-3.5Ag displayed a yield stress above 25 MPa, and extension in excess of 8%. The analysis of the surface was performed, revealing that the increase of the yield stress influenced the appearance of specific prints given by the transfer wheels. The deepest prints were measured for Sn-3.5Ag and they were maximum 100 μm. The other two materials were stiffer and the prints have depths below 50 μm. According to the obtained results, each of the tested materials can be an appropriate solution to filament use for the FDM 3D printing process.
Different extensions of the standard model of particle physics, such as braneworld or mirror matter models, predict the existence of a neutron sterile state, possibly as a dark matter candidate. This ...Letter reports a new experimental constraint on the probability p for neutron conversion into a hidden neutron, set by the STEREO experiment at the high flux reactor of the Institut Laue-Langevin. The limit is p<3.1×10^{-11} at 95% C.L. improving the previous limit by a factor of 13. This result demonstrates that short-baseline neutrino experiments can be used as competitive passing-through-walls neutron experiments to search for hidden neutrons.
.
The STEREO experiment measures the electron antineutrino spectrum emitted in a research reactor using the inverse beta decay reaction on H nuclei in a gadolinium loaded liquid scintillator. The ...detection is based on a signal coincidence of a prompt positron and a delayed neutron capture event. The simulated response of the neutron capture on gadolinium is crucial for the comparison with data, in particular in the case of the detection efficiency. Among all stable isotopes,
155
Gd and
157
Gd have the highest cross sections for thermal neutron capture. The excited nuclei after the neutron capture emit gamma rays with a total energy of about 8MeV. The complex level schemes of
156
Gd and
158
Gd are a challenge for the modeling and prediction of the deexcitation spectrum, especially for compact detectors where gamma rays can escape the active volume. With a new description of the Gd (n,
γ
) cascades obtained using the FIFRELIN code, the agreement between simulation and measurements with a neutron calibration source was significantly improved in the STEREO experiment. A database of ten millions of deexcitation cascades for each isotope has been generated and is now available for the user.
Selective catalyst reduction is one of the most affordable and successful technologies aimed at reducing NOx emissions from diesel engines. However, the reduction process can be achieved if a certain ...temperature is reached for the ceramic substrate of the catalytic core. The required temperatures for catalytic reaction vary from 2500 C to 4500 C depending on the technology applied in the catalytic processes. This paper aims at presenting preliminary research in microwave cordierite heating, which is a type of magnesium aluminium silicate used as ceramic honeycomb substrate (catalyst monolith) in the after treatment system in the automotive industry. The research focused on testing the Mg2Al4Si5O18 composite material (cordierite) for different microwave heating regimes in order to establish the level of microwave power required for fast heating. This application will be subject for the further development of new MW-SCR after treatment systems in order to reduce the NOx emissions at cold start engine or low operating regimes of non-road mobile machinery engines. The ceramic composite material was heated for 5 levels of microwave power, from 600 W to 1400 W, using a 6 kW microwave generator coupled with a matching load impedance tuner, and the temperatures were recorded using an IR pyrometer.
Coherent neutrino-nucleus scattering is a promising new tool in the toolbox of electroweak precision measurements at low
q
-transfer. It will enable precise measurements of standard model (SM) ...physics like the running of the Weinberg angle but also the search for new physics beyond the SM like sterile neutrinos. The
Nucleus
experiment aims at the first detection of fully coherent neutrino-nucleus scattering at the Chooz power plant in France, using its two 4GW
th
reactor cores as high-intensity source for anti-neutrinos. For this endeavour a new experimental site, the Very Near Site (VNS), with a shallow rock overburden of
≈
3
m w.e. is under development. To be competitive in this challenging environment,
Nucleus
developed the novel concept of fiducialised cryogenic bolometers based on CaWO
4
monocrystals operated at
O
(10 mK). The signature of a coherent neutrino-nucleus scattering is a nuclear recoil at the 10 eV-scale. Currently,
Nucleus
is preparing its first phase with 10 g of target mass at the VNS. In this contribution, we will first introduce
Nucleus
, report its current state and give an outlook to its future.
A quantitative analysis of blurring and its dependence on the stencil-substrate gap and the deposition parameters in stencil lithography, a high resolution shadow mask technique, is presented. The ...blurring is manifested in two ways: first, the structure directly deposited on the substrate is larger than the stencil aperture due to geometrical factors, and second, a halo of material is formed surrounding the deposited structure, presumably due to surface diffusion. The blurring is studied as a function of the gap using dedicated stencils that allow a controlled variation of the gap. Our results show a linear relationship between the gap and the blurring of the directly deposited structure. In our configuration, with a material source of approximately 5 mm and a source-substrate distance of 1 m, we find that a gap size of approximately 10 microm enlarges the directly deposited structures by approximately 50 nm. The measured halo varies from 0.2 to 3 microm in width depending on the gap, the stencil aperture size and other deposition parameters. We also show that the blurring can be reduced by decreasing the nominal deposition thickness, the deposition rate and the substrate temperature.
PDF
