Narodna in univerzitetna knjižnica, Ljubljana (NUK)
-
The influence of lubrication and surface topography on performance limits in mechanical seals : doctoral thesisVezjak, AntonMechanical seals are dynamic shaft seals in which primary sealing takes place between surfaces in the sliding contact of two seal faces. Many factors influence the performance of mechanical seals, ... but other than material selection, hardly any factor is so vital as the surface roughness or topography of the sealing rings. Characterization of sealing surfaces is usually presented by roughness parameters such as the average roughness Ra, which is usually insufficient. Thus, from the tribological point of view, other parameters such as core-roughness depth, reduced-peak height and reduced-valley depth are used. The self-maintaining interface lubrication mechanism is another essential feature of mechanical seals, which controls the sealing function, friction, wear, and seal life. Which lubrication regime will be present in the sealing interface depends on many factors, amongst which operating conditions, seal ring surface characteristics, seal face material and fluid properties prevail. Therefore, in order to predict seal performance limits identification of the lubrication regime is significiant. The most common way to identify the lubrication regime in seals is by analyzing Stribeck-type f-G curves. However, a characteristic frequently observed and not yet fully understood in these curves is that the transition point from a mixed to a hydrodynamic lubrication regime differs even for seals of the same design. In experimental tests two types of stepping pressure-velocity tests were performed: one with varying speed and one with varying net sealing pressure. Parameters such as temperature and displacement of the seal seat, fluid temperature, friction torque, normal load on the sealing contact, shaft speed and leakage rate were monitored on-line. Commercially available self-mated alumina was tested in tap water. Different roughness was obtained by plane grinding, fine grinding and polishing. Sealing surfaces were characterized by 3D stylus profilometry and by analyzing various roughness parameters before and after the tests. Lubrication regimes were identified by Stribeck type curves. The results indicate that surface roughness directly influences the lubrication regime and performance limit. The regime transition G value varied with operating conditions. The influence of roughness on the regime transition was negligible at low speeds. At higher speeds in load study tests, fine ground surfaces exhibited the highest hydrodynamic load support of all surfaces. The correlation functions between speed, load and the transition G value were obtained for all surfaces. A random residual waviness was probably the source of the hydrodynamic load support in majority of seal tests. It was also the basic for the hydrodynamic wave-model. A comparison of results between a model and experiment showed quite satisfactory agreement in full film lubrication, whereas in a mixed regime apparently two different lubricating mechanisms were involved in the seal operation. The first was still to some degree comparable with the wave-model. The other was probably associated with mechanisms of parallel sliding lubrication. Here much lower friction coefficients were exhibited than those predicted by the wave-model. Only surfaces ground with SiC paper and plane ground surfaces, for which the ratio Rpk/Rk was the lowest, were associated with the latter lubrication mechanism. The performance limit of a seal was defined by a wear transition characterized by brittle fracture of alumina. Different criteria for evaluating the performance limit with a different level of complexity were used: the PV limit, the frictional power limit and the mechanical and thermal severity index. The PV limit has a strong dependence on lubricating conditions and the size of the real contact area. It seems that the friction power limit is a characteristic material parameter, since it was independent of different lubrication conditions as well as the testing procedure. The thermal severity index gave high satisfactory agreement with experiment, excerpt at lower speedsVrsta gradiva - disertacija ; neleposlovje za odrasleZaložništvo in izdelava - Ljubljana : [A. Vezjak], 2003Jezik - angleškiCOBISS.SI-ID - 6873115
Avtor
Vezjak, Anton
Drugi avtorji
Vižintin, Jože
Teme
Mehanska drsna tesnila |
Disertacije |
tesnila |
hrapavost |
topografija površine |
tribologija |
modeliranje |
obraba |
trenje |
mazanje |
mešano mazanje |
keramika
![loading ... loading ...](themes/default/img/ajax-loading.gif)
Rezervirajte gradivo na želenem mestu prevzema.
Mesto prevzema |
Status gradiva | Rezervacija |
---|---|---|
Časopisna čitalnica |
prosto - za čitalnico
|
|
Velika čitalnica |
prosto - za čitalnico
|
Signatura – lokacija, inventarna št. ... |
Status izvoda |
---|---|
GS II 0000549425 glavno skladišče GS II 549425 glavno skladišče |
prosto - za čitalnico
|
![loading ... loading ...](themes/default/img/ajax-loading.gif)
![loading ... loading ...](themes/default/img/ajax-loading.gif)
![loading ... loading ...](themes/default/img/ajax-loading.gif)
Vnos na polico
Trajna povezava
- URL:
Faktor vpliva
Dostop do baze podatkov JCR je dovoljen samo uporabnikom iz Slovenije. Vaš trenutni IP-naslov ni na seznamu dovoljenih za dostop, zato je potrebna avtentikacija z ustreznim računom AAI.
Leto | Faktor vpliva | Izdaja | Kategorija | Razvrstitev | ||||
---|---|---|---|---|---|---|---|---|
JCR | SNIP | JCR | SNIP | JCR | SNIP | JCR | SNIP |
Baze podatkov, v katerih je revija indeksirana
Ime baze podatkov | Področje | Leto |
---|
Povezave do osebnih bibliografij avtorjev | Povezave do podatkov o raziskovalcih v sistemu SICRIS |
---|---|
Vezjak, Anton | 19047 |
Vižintin, Jože | 00812 |
Vir: Osebne bibliografije
in: SICRIS
Izberite prevzemno mesto:
Prevzem gradiva po pošti
Naslov za dostavo:
Med podatki člana manjka naslov.
Storitev za pridobivanje naslova trenutno ni dostopna, prosimo, poskusite še enkrat.
S klikom na gumb "V redu" boste potrdili zgoraj izbrano prevzemno mesto in dokončali postopek rezervacije.
S klikom na gumb "V redu" boste potrdili zgoraj izbrano prevzemno mesto in naslov za dostavo ter dokončali postopek rezervacije.
S klikom na gumb "V redu" boste potrdili zgoraj izbrani naslov za dostavo in dokončali postopek rezervacije.
Obvestilo
Trenutno je storitev za avtomatsko prijavo in rezervacijo nedostopna. Gradivo lahko rezervirate sami na portalu Biblos ali ponovno poskusite tukaj kasneje.
Gesla v Splošnem geslovniku COBISS
Izbira mesta prevzema
Gradivo iz matične enote je brezplačno. Če je gradivo na mesto prevzema dostavljeno iz drugih enot, lahko knjižnica to storitev zaračuna.
Mesto prevzema | Status gradiva | Rezervacija |
---|
Rezervacija v teku
Prosimo, počakajte trenutek.
Rezervacija je uspela.
Rezervacija ni uspela.
Rezervacija...
Članska izkaznica:
Mesto prevzema:
Naročanje gradiva za izposojo v čitalnice
Naročanje kopij člankov
Urnik dostave gradiva z oznako DS v signaturi