This paper presents a new dynamic model for the simulation of power-transmission-line galloping. The energy approach using the assumed mode method was used to derive equations of motion for a single ...transmission line and double transmission lines connected by spring spacers. Equations of motion are expressed in matrix form, which simplifies numerical analysis and saves computational time. The dynamic models were verified experimentally by comparing theoretical natural frequencies with measured natural frequencies of real transmission lines installed in the test site. Accelerometers and a CCD camera were used to measure vibrations, and an image processing technique was used to trace a circular target mounted on the line. Experimental results are in good agreement with theoretical results, which validate the dynamic models derived in this study. Galloping forces were modeled by assuming quasi-steady aerodynamic lift and drag, which enabled us to predict the galloping phenomena. Numerical simulation results are presented.
고속회전시험기를 활용한 가스터빈 동익의 내구성 시험 이두영; 김두수; 손태하 ...
KEPCO Journal on electric power and energy,
2018, Letnik:
4, Številka:
1
Journal Article
Odprti dostop
The long-term research and development for the production of domestic blades has been consistently performed. As the direct and indirect results of its nationwide technologies in precision casting ...have been improved as well as maintenance costs for turbine machinery has been reduced. Whereas, there are still not a few concerns about the reliability of newly manufactured blades in spite of the quality certificate in metallurgical and mechanical properties. A spin tester is a machine that gives centrifugal loading to a rotating part, and its practical application is the overspeed test that is usually used to check the quality of products. A new spin rig has been constructed in KEPCO Research Institute for the purpose of evaluating the reliability of blades. In this paper, the test methodology for low cycle fatigue damage mechanism as well as the overspeed test for newly developed blades is described, and their reliability is evaluated too. 가스터빈 동익에 대한 지속적인 국산화 개발이 추진되어, 국내 정밀 주조 기술을 향상시키고, 동익의 유지 보수 비용을 낮추는 등의 직간접적인 긍정적 효과를 가져왔지만, 여전히 국산화 개발품이 발전소에서 안정적인 실사용이 가능한지에 대한 우려가 존재한다. 향상된 소재와 주조기술을 바탕으로 조직학적, 기계적 성질에서 충분한 품질을 확보하였더라도, 개발품을 대상으로 다양한 신뢰성 검증이 요구되는 이유이다. 고속회전시험기는 로터, 디스크 등의 회전체에 원심력을 가하여, 이에 따른 제품의 특성을 분석하기 위한 시험장비로 일반적으로 과속도시험을 통한 최종적인 품질검사에 주로 사용된다. 본 논문에서는 전력연구원에 구축된 고속회전시험기를 활용한 가스터빈 동익에 대한 과속도시험을 포함한 저주기피로시험 사례를 중심으로 신뢰성 시험 및 평가 결과를 기술하였다.
In this paper, the wind tunnel test for the measurement of aerodynamic characteristics of transmission conductors with asymmetric sections is described. A single conductor model and bundled conductor ...models with ice accreted shapes are tested both in steady and turbulent flow, and the aerodynamic coefficients are acquired. Transmission conductor galloping is a kind of wind-induced vibration which is characterized by primarily vertical oscillation with a very low frequency and a high amplitude. It is well known that transmission conductor galloping is generally caused by moderately strong, steady winds when a transmission conductor has an asymmetric cross-section shaped by accreted ice. Galloping should be considered from the design stage of overhead lines because it can cause severe wear and fatigue damage to attachments as well as transmission conductors. It is reported that there have been normally 20 events of galloping per year in Korea, which may be followed by serious consequences in the electric power system. Therefore, this research is performed to measure aerodynamic characteristics of ice accreted transmission conductors to understand and control transmission conductor galloping so that it would help to prevent unexpected failures and reduce the maintenance costs caused by galloping. 본 논문은 송전선로 갤러핑 현상 분석을 위해 요구되는 비대칭 송전선의 공기력 계수 측정에 관한 것으로, 세 종류의 비대칭 단면으로 구성된 단도체, 2도체 및 4도체 모형에 대해서 난류 조건에서의 풍동실험을 수행하였다. 송전선로 갤러핑은 비대칭의 착빙된 송전선에 안정된 바람이 작용하는 경우 발생하는 유체유발진동의 한 종류로, 상간 이격거리와 송전탑 하중의 계산 등 송전선의 설계시 고려해야하는 주요 인자 중 하나이다. 갤러핑에 의해 발생하는 반복적인 변동 하중은 송전선을 포함한 체결 부품 등에 큰 동응력을 발생시키는 것을 고려하여, 송전선을 비롯한 각종 부품은 마모와 피로손상에 견딜 수 있는 충분한 내구성을 가져야 한다. 국내에서도 빙설해에 의한 송전선로의 고장은 급격한 전압 강하로 인한 전기 품질에 큰 영향을 끼치는 주요 원인이 되고 있으며, 매년 약 20건 이상씩 발생하고 있는 점을 고려해, 안정적인 전력 공급과 유지, 보수 비용을 절감하기 위해서 갤러핑 현상에 대해서 기초부터 체계적인 접근이 요구되고 있다.
The reliability on high cycle fatigue damage mechanism for new blades manufactured by reverse-engineering is demonstrated by success-run test. Turbine blades always experience various dynamic loads ...in turbine operation, as well as being in resonance condition and forced by fluid-induced vibrations mostly during run-up/down, which may accumulate high cycle damage to the blades. The accidents caused by blade failure especially incur not only a lot of troubles to the machinery but also huge financial losses. Therefore it is necessary to verify the reliability of blades in advance for the safe use. The success run test for the reliability demonstration is designed and performed for the new blades using the technique known as resonant high cycle fatigue testing. $1100^{\circ}C$급 가스터빈 동익의 국산화 개발품에 대한 신뢰성을 무고장시험법에 의해 평가하였다. 터빈 동익은 기동, 정지 중에 발생하는 공진 또는 유체유발진동을 겪는 등 터빈 운전 중 상시 다양한 동하중에 노출되어 있으며, 이러한 변동하중은 터빈 동익에 고주기피로손상을 초래한다. 특히 동익의 파손에 의한 사고는 타 설비로의 파급이 크고, 막대한 경제적 피해를 야기하기 때문에, 발전소의 안정적인 운전을 위해 동익의 신뢰성이 우선 검증되어야 한다. 동익에 균열을 일으키기 위해서 전자식 가진기를 이용하여 공진에 의한 증폭된 동하중을 부과하였다. 가스터빈 동익의 수명분포를 와이블 분포로 가정하여 를 시험 시간을 계산하고, 시료 1개의 고장을 허용하는 조건으로 총 5개의 개발품을 대상으로 시험을 수행하여, 개발품 동익의 목표 수명을 90% 신뢰도로 보증할 수 있다는 것을 90% 신뢰수준에서 확인하였다.
배열형 음향센서를 이용한 발전설비 소음원 탐지시스템 개발 손석만; 김동환; 이욱륜 ...
KEPCO Journal on electric power and energy,
2015, Letnik:
1, Številka:
1
Journal Article
Odprti dostop
In this study, it has been initiated to investigate the specific abnormal vibration signal that has been captured in the power equipment. Array Microphone can be used in order to detect the direction ...and the position of the noise source. It is possible to track the abnormal mechanical noise in the power plant by utilizing the program and the microphone array system developed from this research. Array microphone system can be operated as a constant monitoring system.
In this research paper, we study on how to decrease the high vibration of turbine hood casings which are main facilities of power generation industry. Cause of Standard coal-fired power 500MW ...facilities turbine hoods' high vibration is that Natural frequency of hood casing designed in near domain frequency, when they are making hoods. We investigate to reduce high vibration at hood casing. We use FEM method to found how to avoid resonance, and test to confirm that our FEM result. We Finally attach minium mass plate at hood casing to avoid resonance and high vibration reduce lower $100{\mu}m$.
