The combination of different propulsion and energy storage systems for hybrid vehicles is changing the focus in the field of powertrain calibration. Shorter time-to-market as well as stricter legal ...requirements regarding the validation of Real Driving Emissions (RDE) require the adaptation of current procedures and the implementation of new technologies in the powertrain development process. In order to achieve highest efficiencies and lowest pollutant emissions at the same time, the layout and calibration of the control strategies for the powertrain and the exhaust gas aftertreatment system must be precisely matched. An optimal operating strategy must take into account possible trade-offs in fuel consumption and emission levels, both under highly dynamic engine operation and under extended environmental operating conditions. To achieve this with a high degree of statistical certainty, the combination of advanced methods and the use of virtual test benches offers significant potential. An approach for such a combination is presented in this paper. Together with a Hardware-in-the-Loop (HiL) test bench, the novel methodology enables a targeted calibration process, specifically designed to address calibration challenges of hybridized powertrains. Virtual tests executed on a HiL test bench are used to efficiently generate data characterizing the behavior of the system under various conditions with a statistically based evaluation identifying white spots in measurement data, used for calibration and emission validation. In addition, critical sequences are identified in terms of emission intensity, fuel consumption or component conditions. Dedicated test scenarios are generated and applied on the HiL test bench, which take into account the state of the system and are adjusted depending on it. The example of one emission calibration use case is used to illustrate the benefits of using a HiL platform, which achieves approximately 20% reduction in calibration time by only showing differences of less than 2% for fuel consumption and emission levels compared to real vehicle tests.
Reducing air pollution caused by emissions from road traffic, especially in urban areas, is an important goal of legislators and the automotive industry. The introduction of so-called “Real Driving ...Emission” (RDE) tests for the homologation of vehicles with internal combustion engines according to the EU6d legislation was a fundamental milestone for vehicle and powertrain development. Due to the introduction of non-reproducible on-road emission tests with “Portable Emission Measurement Systems” (PEMS) in addition to the standardized emission tests on chassis dynamometers, emission aftertreatment development and validation has become significantly more complex. For explicit proof of compliance with the emission and fuel consumption regulations, the legislators continue to require the “Worldwide Harmonized Light Duty Vehicle Test Cycle” (WLTC) on a chassis dynamometer. For calibration purposes, also various RDE profiles are conducted on the chassis dynamometer. However, the combination of precisely defined driving profiles on the chassis dynamometer and the dynamics-limiting boundary conditions in PEMS tests on the road still lead to discrepancies between the certified test results and the real vehicle behavior. The expected future emissions standards to replace EU6d will therefore force even more realistic RDE tests. This is to be achieved by significantly extending the permissible RDE test boundary conditions, such as giving more weight to the urban section of an RDE test. In addition, the introduction of limit values for previously unregulated pollutants such as nitrogen dioxide (NO2), nitrous oxide (N2O), ammonia (NH3) and formaldehyde (CH2O) is being considered. Furthermore, the particle number (for diameters of solid particles > 10 nm: PN10), the methane (CH4) emissions and emissions of non-methane organic gases (NMOG) shall be limited and must be tested. To simplify the test procedure in the long term, the abandonment of predefined chassis dyno emission tests to determine the pollutant emission behavior is under discussion. Against this background, current testing, validation, and development methods are reviewed in this paper. New challenges and necessary adaptations of current approaches are discussed and presented to illustrate the need to consider future regulatory requirements in today’s approaches. Conclusions are drawn and suggestions for a robust RDE validation procedure are formulated.
With the Euro 7 pollutant emission legislation currently under discussion, advanced and more efficient exhaust aftertreatment systems are being developed. The technologies required for these are ...leading to an increase in the number of components and control systems requiring diagnoses strategies under the on-board diagnostics (OBD) legislation. With concurrent shorter development times and significant reductions in budgets allocated to conventional powertrain development, challenges in the field of OBD calibration and verification are already rising sharply. In response to these challenges, hardware-in-the-loop (HiL) approaches have been successfully introduced to support and replace conventional development methods. The use of complex simulation models significantly improves the quality of calibrations while minimizing the number of required prototype vehicles and test resources, thus reducing development costs. This paper presents a feasibility study for moving OBD-related calibration and validation tasks from the vehicle to a HiL platform. In this context, the calibration and verification process of an active diagnostic for monitoring the condition of the three-way catalyst (TWC) and the oxygen sensors in the exhaust aftertreatment system is presented. It is shown that all relevant signals are simulated with sufficient accuracy to ensure a robust transfer from the vehicle to a HiL test bench. Special attention is given to the simulation of aged components and their influence on the emission behavior of the system. Furthermore, it is discussed that transferring OBD tasks from the vehicle to the HiL test bench could result in significant savings in development time and a reduction in the number of physical prototype vehicles and test resources required.
In view of the deliberations on new Euro 7 emission standards to be introduced by 2025, original equipment manufacturers (OEMs) are already hard at work to further minimise the pollutant emissions of ...their vehicles. A particular challenge in this context will be compliance with new particulate number (PN) limits. It is expected that these will be tightened significantly, especially by including particulates down to 10 nm. This will lead to a substantially increased effort in the calibration of gasoline particulate filter (GPF) control systems. Therefore, it is of great interest to implement advanced methods that enable shortened and at the same time more accurate GPF calibration techniques. In this context, this study presents an innovative GPF calibration procedure that can enable a uniquely efficient development process. In doing so, some calibration work packages involving GPF soot loading and regeneration are transferred to a modern burner test bench. This approach can minimise the costly and time-consuming use of engine test benches for GPF calibration tasks. Accurate characterisation of the particulate emissions produced after a cold start by the target engine in terms of size distribution, morphology, and the following exhaust gas backpressure and burn-off rates of the soot inside the GPF provides the basis for a precise reproduction and validation process on the burner test bench. The burner test bench presented enables the generation of particulates with a geometric mean diameter (GMD) of 35 nm, exactly as they were measured in the exhaust gas of the engine. The elemental composition of the burner particulates also shows strong similarities to the particulates produced by the gasoline engine, which is further confirmed by matching burn-off rates. Furthermore, the exhaust backpressure behaviour can accurately be reproduced over the entire loading range of the GPF. By shifting GPF-related calibration tasks to the burner test bench, total filter loading times can be reduced by up to 93%.
Further reducing greenhouse gas and pollutant emissions from road vehicles is a major task for the automotive industry. Stricter regulations regarding emissions and fleet fuel consumption require the ...continuous development of new powertrains and methods. In particular, the combination of hybrid powertrains on the technical side and the focus on real driving emissions (RDE) on the legislative side pose significant challenges to the vehicle calibration process. Against this background, new test methods and environments are being investigated to counteract the high number of interactions between hybrid drive systems and quasi-infinite test conditions due to RDE. Complementary to new test environments, innovative methods for data analysis are needed that allow the exploitation of the complete potential of measurement data. The application of such a method in the field of emission calibration is presented in this paper. For this purpose, a clustering method (HDBSCAN) is applied to critical sequences from emission tests. Within this presentation, the clustering process is based on a single signal only. This paper shows how signals of various characteristics can be processed with dynamic time warping and generically structured with the clustering method used. Here, 959 single events are automatically categorized into 24 clusters. This provides a new basis for system evaluation, enabling the automatic identification, categorization, and prioritization of calibration weaknesses. Using twelve signals of different characteristics, the generic usability of the clustering method is demonstrated.
The systematic analysis of measurement data allows a large amount of information to be obtained from existing measurements in a short period of time. Especially in vehicle development, many ...measurements are performed, and large amounts of data are collected in the process of emission calibration. With the introduction of Real Driving Emissions Tests, the need for targeted analysis for efficient and robust calibration of a vehicle has further increased. With countless possible test scenarios, test-by-test analysis is no longer possible with the current state-of-the-art in calibration, as it takes too much time and can disregard relevant data when analyzed manually. In this article, therefore, a methodology is presented that automatically analyzes exhaust measurement data in the context of emission calibration and identifies emission-related critical sequences. For this purpose, moving analyzing windows are used, which evaluate the exhaust emissions in each sample of the measurement. The detected events are stored in tabular form and are particularly suitable for condensing the collected measurement data to a required amount for optimization purposes. It is shown how different window settings influence the amount and duration of detected events. With the example used, a total amount of 454 events can be identified from 60 measurements, reducing 184,623 s of measurements to a relevant amount of 12,823 s.
This dataset includes the signal traces for the events used in the publication "Applying Density-Based Clustering for the Analysis of Emission Events in Real Driving Emissions Calibration", MDPI ...Future Transportation, 2024 (doi: 10.3390/futuretransp4010004).
The data is available in a frequency of 1 Hz and the signals are arranged in separate tables. Please note, that the order of the events is not consistent for the individual signals.
The general vehicle specifications are listed below. For further information please refer to the paper.
Characteristic
Unit
Value
Vehicle weight
kg
> 2000
Fuel
-
Gasoline
Engine type
-
Turbo-charged 8 cylinder
Engine power and torque
kW / Nm
> 400 / > 600
Cubic capacity
cm^3
~ 4000
Transmission
-
Automatic transmission (AT)
Drivetrain
-
All-wheel drive (AWD)
Exhaust aftertreatment system (EATS)
-
Three-way catalytic converter (TWC) and gasoline particulate filter (GPF)
Condition of EATS
-
Stabilized EATS (~ 70 % of tests) and aged EATS (~ 30 % tests)
Emission target
-
EU6d
PDF
