An amorphous metal-organic framework (aMOF) UiO-66 (Zr-MOF) was prepared directly from synthesis, different from experiments involving heating, pressure, and ball-milling by other researchers. The ...as-prepared amorphous UiO-66 has been successfully used as a supercapacitor electrode material, exhibiting a high specific capacitance (920 F g−1 at 10 mV s−1) superior to crystalline UiO-66. It has been verified that the material after reaction can still remain amorphous state by transmission electron microscopy (TEM). The capacitance of amorphous UiO-66 can maintain 610 F g−1 after 5000 cycles, suggesting its promising potential as a supercapacitor electrode material.
•Amorphous UiO-66 is produced directly from synthesis.•Amorphous UiO-66 is compared with crystal UiO-66 to demonstrate its prosperities.•Amorphous UiO-66 is first used as a supercapacitor electrode material.•Amorphous UiO-66 exhibits a superior specific capacitance to crystalline UiO-66.•This preparation could be taken to make more other amorphous materials.
The use of reticular materials in the electrochemical reduction of carbon dioxide to value-added products has the potential to enable tunable control of the catalytic performance through the ...modulation of chemical and structural features of framework materials with atomic precision. However, the tunable functional performance of such systems is still largely hampered by their poor electrical conductivities. This work demonstrates the use of four systematic structural analogs of conductive two-dimensional (2D) metal–organic frameworks (MOFs) made of metallophthalocyanine (MPc) ligands linked by Cu nodes with electrical conductivities of 2.73 × 10–3 to 1.04 × 10–1 S cm–1 for the electrochemical reduction of CO2 to CO. The catalytic performance of the MOFs, including the activity and selectivity, is found to be hierarchically governed by two important structural factors: the metal within the MPc (M = Co vs Ni) catalytic subunit and the identity of the heteroatomic cross-linkers between these subunits (X = O vs NH). The activity and selectivity are dominated by the choice of metal within MPcs and are further modulated by the heteroatomic linkages. Among these MOFs, CoPc–Cu–O exhibited the highest selectivity toward CO product (Faradaic efficiency FECO = 85%) with high current densities up to −17.3 mA cm–2 as a composite with carbon black at 1:1 mass ratio) at a low overpotential of −0.63 V. Without using any conductive additives, the use of CoPc–Cu–O directly as an electrode material was able to achieve a current density of −9.5 mA cm–2 with a FECO of 79%. Mechanistic studies by comparison tests with metal-free phthalocyanine MOF analogs supported the dominant catalytic role of the central metal of the phthalocyanine over Cu nodes. Density-functional theory calculations further suggested that, compared with the NiPc-based and NH-linked analogs, CoPc-based and O-linked MOFs have lower activation energies in the formation of carboxyl intermediate, in line with their higher activities and selectivity. The results of this study indicate that the use of 2D MPc-based conductive framework materials holds great promise for achieving efficient CO2 reduction through strategic ligand engineering with multiple levels of tunability.
Lithium sulfur batteries have brought significant advancement to the current state-of-art battery technologies because of their high theoretical specific energy, but their wide-scale implementation ...has been impeded by a series of challenges, especially the dissolution of intermediate polysulfides species into the electrolyte. Conductive polymers in combination with nanostructured sulfur have attracted great interest as promising matrices for the confinement of lithium polysulfides. However, the roles of different conductive polymers on the electrochemical performances of sulfur electrode remain elusive and poorly understood due to the vastly different structural configurations of conductive polymer–sulfur composites employed in previous studies. In this work, we systematically investigate the influence of different conductive polymers on the sulfur cathode based on conductive polymer-coated hollow sulfur nanospheres with high uniformity. Three of the most well-known conductive polymers, polyaniline (PANI), polypyrrole (PPY), and poly(3,4-ethylenedioxythiophene) (PEDOT), were coated, respectively, onto monodisperse hollow sulfur nanopsheres through a facile, versatile, and scalable polymerization process. The sulfur cathodes made from these well-defined sulfur nanoparticles act as ideal platforms to study and compare how coating thickness, chemical bonding, and the conductivity of the polymers affected the sulfur cathode performances from both experimental observations and theoretical simulations. We found that the capability of these three polymers in improving long-term cycling stability and high-rate performance of the sulfur cathode decreased in the order of PEDOT > PPY > PANI. High specific capacities and excellent cycle life were demonstrated for sulfur cathodes made from these conductive polymer-coated hollow sulfur nanospheres.
Lithium metal has shown great promise as an anode material for high-energy storage systems, owing to its high theoretical specific capacity and low negative electrochemical potential. Unfortunately, ...uncontrolled dendritic and mossy lithium growth, as well as electrolyte decomposition inherent in lithium metal-based batteries, cause safety issues and low Coulombic efficiency. Here we demonstrate that the growth of lithium dendrites can be suppressed by exploiting the reaction between lithium and lithium polysulfide, which has long been considered as a critical flaw in lithium-sulfur batteries. We show that a stable and uniform solid electrolyte interphase layer is formed due to a synergetic effect of both lithium polysulfide and lithium nitrate as additives in ether-based electrolyte, preventing dendrite growth and minimizing electrolyte decomposition. Our findings allow for re-evaluation of the reactions regarding lithium polysulfide, lithium nitrate and lithium metal, and provide insights into solving the problems associated with lithium metal anodes.
Silicon is widely recognized as one of the most promising anode materials for lithium-ion batteries due to its 10 times higher specific capacity than graphite. Unfortunately, the large volume change ...of Si materials during their lithiation/delithiation process results in severe pulverization, loss of electrical contact, unstable solid–electrolyte interphase (SEI), and eventual capacity fading. Although there has been tremendous progress to overcome these issues through nanoscale materials design, improved volumetric capacity and reduced cost are still needed for practical application. To address these issues, we design a nonfilling carbon-coated porous silicon microparticle (nC-pSiMP). In this structure, porous silicon microparticles (pSiMPs) consist of many interconnected primary silicon nanoparticles; only the outer surface of the pSiMPs was coated with carbon, leaving the interior pore structures unfilled. Nonfilling carbon coating hinders electrolyte penetration into the nC-pSiMPs, minimizes the electrode–electrolyte contact area, and retains the internal pore space for Si expansion. SEI formation is mostly limited to the outside of the microparticles. As a result, the composite structure demonstrates excellent cycling stability with high reversible specific capacity (∼1500 mAh g–1, 1000 cycles) at the rate of C/4. The nC-pSiMPs contain accurate void space to accommodate Si expansion while not losing packing density, which allows for a high volumetric capacity (∼1000 mAh cm–3). The areal capacity can reach over 3 mAh cm–2 with the mass loading 2.01 mg cm–2. Moreover, the production of nC-pSiMP is simple and scalable using a low-cost silicon monoxide microparticle starting material.
Sulfur is an exciting cathode material with high specific capacity of 1,673 mAh/g, more than five times the theoretical limits of its transition metal oxides counterpart. However, successful ...applications of sulfur cathode have been impeded by rapid capacity fading caused by multiple mechanisms, including large volume expansion during lithiation, dissolution of intermediate polysulfides, and low ionic/electronic conductivity. Tackling the sulfur cathode problems requires a multifaceted approach, which can simultaneously address the challenges mentioned above. Herein, we present a scalable, room temperature, one-step, bottom-up approach to fabricate monodisperse polymer (polyvinylpyrrolidone)-encapsulated hollow sulfur nanospheres for sulfur cathode, allowing unprecedented control over electrode design from nanoscale to macroscale. We demonstrate high specific discharge capacities at different current rates (1,179, 1,018, and 990 mAh/g at C/10, C/5, and C/2, respectively) and excellent capacity retention of 77.6% (at C/5) and 73.4% (at C/2) after 300 and 500 cycles, respectively. Over a long-term cycling of 1,000 cycles at C/2, a capacity decay as low as 0.046% per cycle and an average coulombic efficiency of 98.5% was achieved. In addition, a simple modification on the sulfur nanosphere surface with a layer of conducting polymer, poly(3,4-ethylenedioxythiophene), allows the sulfur cathode to achieve excellent high-rate capability, showing a high reversible capacity of 849 and 610 mAh/g at 2C and 4C, respectively.
Although sodium (Na) is one of the most promising alternatives to lithium as an anode material for next-generation batteries, uncontrollable Na dendrite growth still remains the main challenge for Na ...metal batteries. Herein, a novel 1D/2D Na3Ti5O12-MXene hybrid nanoarchitecture consisting of Na3Ti5O12 nanowires grown between the MXene nanosheets is synthesized by a facile approach using cetyltrimethylammonium bromide (CTAB)-pretreated Ti3C2 MXene. Used as a matrix for the Na metal anode, the Na3Ti5O12 nanowires, formed benefiting from the CTAB stabilization, have chemical interaction with Na and thus provide abundant Na nucleation sites. These 1D nanostructures, together with the unique confinement effect from the 2D nanosheets, effectively guide and control the Na deposition within the interconnected nanochannels, preventing the “hot spot” formation for dendrite growth. A stable cycling performance can be achieved at a high current density up to 10 mA cm–2 along with an ultrahigh capacity up to 20 mAh cm–2.
Kupffer cells (KCs) are key regulators of liver immunity composing the principal part of hepatic macrophages even body tissue macrophages. They reside in liver sinusoids towards portal vein. The ...micro-environment shapes KCs unique immunosuppressive features and functions. KCs express specific surface markers that distinguish from other liver macrophages. By engulfing gut-derived foreign products and apoptotic cells without triggering excessive inflammation, KCs maintain homeostasis of liver and body. Heterogeneity of KCs has been identified in different studies. In terms of the origin, adult KCs are derived from progenitors of both embryo and adult bone marrow. Embryo-derived KCs compose the majority of KCs in healthy and maintain by self-renewal. Bone marrow monocytes replenish massively when embryo-derived KC proliferation are impaired. The phenotype of KCs is also beyond the traditional dogma of M1-M2. Functionally, KCs play central roles in pathogenesis of acute and chronic liver injury. They contribute to each pathological stage of liver disease. By initiating inflammation, regulating fibrosis, cirrhosis and tumor cell proliferation, KCs contribute to the resolution of liver injury and restoration of tissue architecture. The underlying mechanism varied by damage factors and pathology. Understanding the characteristics and functions of KCs may provide opportunities for the therapy of liver injury. Herein, we attempt to afford insights on heterogeneity and functions of KCs in liver injury using the existing findings.
Lithium-sulfur batteries have attracted attention due to their six-fold specific energy compared with conventional lithium-ion batteries. Dissolution of lithium polysulfides, volume expansion of ...sulfur and uncontrollable deposition of lithium sulfide are three of the main challenges for this technology. State-of-the-art sulfur cathodes based on metal-oxide nanostructures can suppress the shuttle-effect and enable controlled lithium sulfide deposition. However, a clear mechanistic understanding and corresponding selection criteria for the oxides are still lacking. Herein, various nonconductive metal-oxide nanoparticle-decorated carbon flakes are synthesized via a facile biotemplating method. The cathodes based on magnesium oxide, cerium oxide and lanthanum oxide show enhanced cycling performance. Adsorption experiments and theoretical calculations reveal that polysulfide capture by the oxides is via monolayered chemisorption. Moreover, we show that better surface diffusion leads to higher deposition efficiency of sulfide species on electrodes. Hence, oxide selection is proposed to balance optimization between sulfide-adsorption and diffusion on the oxides.
Electrochemical reduction of carbon dioxide (CO2) into value-added chemicals and fuels provides a promising pathway for environmental and energy sustainability. Copper (Cu) demonstrates a unique ...ability to catalyze the electrochemical conversion of CO2 into valuable multicarbon products. However, developing a rapid, scalable and cost-effective method to synthesize efficient and stable Cu catalysts with high selectivity toward multicarbon products at a low overpotential is still hard to achieve and highly desirable. In this work, we present a facile wet chemistry approach to yield well-defined cuprous halide (CuX, X = Cl, Br or I) microcrystals with different degrees of truncations at edges/vertices, which can be ascribed to the oxidative etching mechanism of halide ions. More importantly, the as-obtained cuprous halides can be electrochemically transformed into varied Cu nanoarchitectures, thus exhibiting distinct CO2 reduction behaviors. The CuI-derived Cu nanofibers composed of self-assembled nanoparticles are reported for the first time, which favor the formation of C2+3 products at a low overpotential with a particular selectivity toward ethane. In comparison, the Cu nanocubes evolved from CuCl are highly selective toward C1 products. For CuBr-derived Cu nanodendrites, C1 products are subject to form at a low overpotential, while C2+3 products gradually become dominant with a favorable formation of ethylene when the potential turns more negative. This work explicitly reveals the critical morphology effect of halide-derived Cu nanostructures on the CO2 product selectivity, and also provides an ideal platform to investigate the structure–property relationship for CO2 electroreduction.