Differently structured aluminum (tri/mono) hydroxide (Al(OH)
3
/AlO(OH)) nanoparticles were prepared and used as thermal-management additives to microfibrillated cellulose (MFC), cast-dried in ...thin-layer films. Both particles increased the thermal stability of the MFC film, yielding 20–23% residue at 600 °C, and up to 57% lowered enthalpy (to 5.5–7.5 kJ/g) at 0.15 wt% of loading, while transforming to alumina (Al
2
O
3
). However, the film containing 40 nm large Al(OH)
3
particles decomposed in a one-step process, and released up to 20% more energy between 300 and 400 °C as compared to the films prepared from smaller (21 nm) and meta-stable AlO(OH), which decomposed gradually with an exothermic peak shifted to 480 °C. The latter resulted in a highly flexible, optically transparent (95%), and mechanically stronger (5.7 GPa) film with a much lower specific heat capacity (0.31–0.28 J/gK compared to 0.68–0.89 J/gK for MFC-Al(OH)
3
and 0.87–1.26 for MFC films), which rendered it as an effective heat-dissipating material to be used in flexible opto-electronics. Low oxygen permeability (2192.8 cm
3
/m
2
day) and a hydrophobic surface (> 60°) also rendered such a film useful in ecologically-benign and thermosensitive packaging.
Bio-solids (biological sludge) from wastewater treatment plants are a significant source of the emission of microplastics (MPs) into the environment. Weakening the structure of MPs before they enter ...the environment may accelerate their degradation and reduce the environmental exposure time. Therefore, we studied the effect of UV-A and UV-C, applied at 70 °C, on three types of MPs, polypropylene (PP), polyethylene (PE), and polyethylene terephthalate (PET), that are commonly found in sewage sludge, using three shapes (fibers, lines, granules). The MPs were exposed to UV radiation in bio-solid suspensions, and to air and water as control. The structural changes in and degradation of the MPs were investigated using Attenuated Total Reflectance–Fourier Transform Infrared Spectrometry (ATR-FTIR) and surface morphology was performed with SEM analysis. UV exposure led to the emergence of carbonyl and hydroxyl groups in all of the PP samples. In PE and PET, these groups were formed only in the bio-solid suspensions. The presence of carbonyl and hydroxyl groups increased with an increasing exposure time. Overall, UV radiation had the greatest impact on the MPs in the bio-solids suspension. Due to the surface-to-volume ratio of the tested samples, which influences the degradation rate, the fibers were more degraded than the other two plastic shapes. UV-A was slightly more effective at degrading the MPs than UV-C. These findings show that ultraviolet radiation in combination with an elevated temperature affects the structure of polymers in wastewater bio-solids, which can accelerate their degradation.
Global design and manufacturing of the materials with superb properties remain one of the greatest challenges on the market. The future progress is orientated towards researches into the material ...development for the production of composites of better mechanical properties to the existing materials. In the field of advanced composites, epoxy molding compounds (EMCs) have attained dominance among the common materials due to their excellent properties that can be altered by adding different fillers. One of the main fillers is often based on silicon dioxide (SiO
). The concept of this study was to evaluate the effects of the selected silica-based fillers on the thermal, rheological, and mechanical properties of EMCs. Various types of fillers with SiO
, including crystalline silica and fused silica, were experimentally studied to clarify the impact of filler on final product. Fillers with different shape (scanning electron microscope, SEM), along with different specific surface area (specific surface area analyzer, BET method) and different chemical structure, were tested to explore their modifications on the EMCs. The influence of the fillers on the compound materials was determined with the spiral flow length (spiral flow test, EMMI), glass transition temperature (differential scanning calorimetry, DSC), and the viscosity (Torque Rheometer) of the composites.
Magnetic extraction offers a rapid and low-cost solution to microplastic (MP) separation, in which we magnetize the hydrophobic surface of MPs to separate them from complex environmental matrices ...using magnets. We synthesized a hydrophobic Fe-silane based nanocomposite (Fe@SiO
/MDOS) to separate MPs from freshwater. Pristine and weathered, polyethylene (PE) and tire wear particles (TWP) of different sizes were used in the study. The weathering of MPs was performed in an accelerated weathering chamber according to ISO 4892-2:2013 standards that mimic natural weathering conditions. The chemical properties and morphology of the Fe@SiO
/MDOS, PE and TWP were confirmed by Fourier transform infrared spectroscopy and Scanning electron microscopy, respectively. The thermal properties of PE and TWP were evaluated by Thermogravimetric analysis. Using 1.00 mg of Fe@SiO
/MDOS nanocomposite, 2.00 mg of pristine and weathered PE were extracted from freshwater; whereas, using the same amount of the nanocomposite, 7.92 mg of pristine TWP and 6.87 mg of weathered TWP were extracted. The retrieval of weathered TWP was 13% less than that of pristine TWP, which can be attributed to the increasing hydrophilicity of weathered TWP. The results reveal that the effectiveness of the magnetic separation technique varies among different polymer types and their sizes; the weathering of MPs also influences the magnetic separation efficiency.
In the presented work, the influence of two flame retardants—ammonium polyphosphates and 2,4,6-triamino-1,3,5-triazine on the polyurethane foam (PUR) systems were studied. In this paper, these ...interactive properties are studied by using the thermal analytical techniques, TGA and DTA, which enable the various thermal transitions and associated volatilization to be studied and enable the connection of the results with thermal and mechanical analysis, as are thermal conductivities, compression and bending behavior, hardness, flammability, and surface morphology. In this way, a greater understanding of what the addition of fire retardants to polyurethane foams means for system flammability itself and, on the other hand, how this addition affects the mechanical properties of PUR may be investigated. It was obtained that retardants significantly increase the fire resistance of the PURs systems while they do not affect the thermal conductivity and only slightly decrease the mechanical properties of the systems. Therefore, the presented systems seem to be applicable as thermal insulation where low heat conductivity coupled with high flame resistance is required.
Polyurethane foam (PUR) is a lightweight, thermally insulating, widely used, and highly flammable material that has after its use an adverse effect on the environment, i.e., PUR disposal is ...considered hazardous. Its flammability can be mitigated using various fire retardants, but they do not change the hazardous nature of waste PUR. Therefore, in the current study, waste PUR with and without flame retardants based on N and P was incorporated into a geopolymer, the alkali-activated material (AAM) based solely on metakaolin, to evaluate the potential recycling route of waste PUR while taking into account its flammability, so it can enter safely into the circular economy through the building industry. To enhance the mechanical properties of the composite, a fresh mixture was irradiated with microwaves. However, the irradiation of geopolymer containing PUR negatively influenced mechanical performance, which led to the evaluation of the behaviour of the complex dielectric constant of PUR and fire retardants. Materials and composites were evaluated regarding their chemistry, mineralogy, microstructure, and porosity to connect the structure with extrinsic properties like geometrical density, thermal conductivity, and fire properties. Nonetheless, positive influences of PUR being encapsulated in the geopolymer were lowered density (from 1.8 to 1.6 kg/l) and improved thermal insulation ability (from 940 to 860 mW/(m·K)) of the composites: with the inclusion of <5 % of PUR, thermal insulation improved by nearly 10 %. However, the contribution of PUR to the composite originated from its skeleton, which has more than 15 times bigger geometrical density (0.81 kg/l) compared to the density of the skeleton (0.047 kg/l). This offers an open field for further advancements of thermal properties, but would also lead to a decrease of the compressive strength, which was already lowered from 90 MPa for 30 % with <5 % of added grated PUR. Furthermore, the flammable nature of PUR and its other drawbacks can be controlled by permanent embedding in the noncombustible structure of geopolymer, making the envelope of sustainable buildings green and safer. Overall, including grated waste PUR in geopolymer represents a promising, easy, cost-effective recycling path with low energy consumption, where the composite cannot develop fire on a scale of pure PUR, even in the worst-case scenario, but only if the composite is designed in a way, that flammable materials cannot join flames during their combustion. This paper gives prospects to other flammable waste materials to be safely used in the circular economy, and to porous materials to shape properties of the composite by their intrinsic and/or extrinsic properties.
Display omitted
•Density of the composite is affected by PUR grating quality more than by its mass.•Well-grated PUR shifts pore sizes of the geopolymer composite to smaller values.•Less than 5 % of grated PUR improves insulation ability of geopolymer by up to 10 %.•Upon fire-safe combustion of PUR, remaining voids become available for gas release.•Voids ensure fewer crack formation during exposure to high temperatures.
Global industries strive towards the production of materials with superior mechanical characteristics, and their development remains a big challenges. One of the more interesting materials that ...exhibit these properties are silicate-filled epoxy molding compounds (EMCs). A good interaction between silicate filler and epoxy matrix is generally needed to achieve advantageous mechanical properties, as well as the desirable rheological behavior of EMCs. Understanding the influence of different organosilane coupling agents on the rheological and mechanical properties of EMCs is essential in the development and optimization of the manufacturing process. For this matter, a mixture of calcium silicate and aluminosilicate was treated by using organosilane coupling agents with different chemical structures and thus treated silicates were applied as fillers in the EMCs. The thermal behavior of the organosilane-modified, silicate-filled EMCs was studied by using differential scanning calorimetry (DSC) and thermomechanical analysis (TMA). Flow-curing behavior (torque rheometer) and spiral flow length measurement (EMMI) were used to monitor the rheological properties and reactivity of the EMCs. The results showed that 3-glycidyloxypropyltrimethoxysilane- and 3-aminopropyltriethoxysilane-treated filler had a greater influence on the tensile strength of hot-pressed test samples, while 3-aminopropyltriethoxysilane and a blend of primary and secondary aminosilanes had a more significant impact on the rheological behavior of the material.
The present review compiles and critically evaluates studies on the synthesis of dimethyl carbonate (DMC) using different techniques and catalysts with reaction conditions, a wide range of ...applications and environmental impact. In this review, we compare different strategies, wide variety of catalysts, and advantages and disadvantages of various DMC synthesis routes. We particularly focus on catalyst advancements for DMC synthesis from transesterification of carbonates/urea, and direct or indirect conversions of CO
2
. Mechanisms of synthesis along with future perspectives have also been discussed. The transesterification of propylene carbonate and ethylene carbonate is an effective process for DMC synthesis. CO
2
with methanol is an emerging route for DMC synthesis. The major problems in various routes such as thermodynamic limitations, low yield and reaction rate, deactivation of catalyst due to hydrolysis have been discussed. Finally, potential applications of DMC and effective use as a multifunctional compound are exemplified.
Cellulose acetate is used in many applications, including for cigarette filters. Unfortunately, unlike cellulose, its (bio)degradability is under question, yet it often ends up uncontrolled in the ...natural environment. The main purpose of this study is to compare the effects of weathering on two types of cigarette filter (classic filters and newer filters that have more recently arrived on the market) following their use and disposal in nature. Microplastics were prepared from polymer parts of used (classic and heated tobacco products-HTP) cigarettes and artificially aged. TG/DTA, FTIR, and SEM analyses were performed both before and after the aging process. Newer tobacco products contain an additional film made of a poly(lactic acid) polymer which, like cellulose acetate, burdens the environment and poses a risk to the ecosystem. Numerous studies have been conducted on the disposal and recycling of cigarette butts and cigarette butt extracts, revealing alarming data that have also influenced the decisions of the EU, who addressed the disposal of tobacco products in the EU Directive (EU) 2019/904. Despite this, there is still no systematic analysis in the literature evaluating the impact of weathering (i.e., accelerated aging) on the degradation of cellulose acetate in classic cigarettes compared with that in newer tobacco products that have recently appeared on the market. This is of particular interest given that the latter have been promoted as being healthier and environmentally friendly. The results show that in cellulose acetate cigarette filters the particle size decreased after accelerated aging. Also, the thermal analysis revealed differences in the behavior of the aged samples, while the FTIR spectra showed no shifts in the position of the peaks. Organic substances break down under UV light, which can be seen by measuring the color change. The PLA film was found to be more stable than cellulose acetate under the influence of UV light.
PDF
