In this paper, the novelty of exploring the applications of the Iraqi Palm Tree Remnants (IPTR) mixed with Nickel Oxide Nanoparticles (NONP) hosted in Polyethylene (PE), called INP substrates, is ...utilized by printing metamaterial (MTM) based high gain microwave antennas on them. The proposed INP substrates are mainly created from pressed flexible organic fibers to suite the ink jet printing technologies. The complex relative constitutive parameters are characterized in terms of permittivity (ε) and permeability (μ) within the frequency range from 2 GHz up to 6 GHz using an open end dielectric probe and a T-stub transmission line technique. To validate the feasibility of the INP substrates, a very fine antenna structure of based a miniaturized Hilbert MTM based dipoles is printed on. A material printer with Sliver Nanoparticles Conductive Ink (SNPCI) is used to print the antenna structure. Commercial software packages, CST Microwave Studio (MWS) and Ansys High Frequency Structure Simulator (HFSS), are used to simulate the proposed antenna based on the measured constitutive parameters. A negligible difference is found between the measured and simulated results. Finally, an attractive effect on the retrieved constitutive parameters of the proposed MTM is found due to the proposed INP substrate.
In this article, the proposed antenna structure is designed for modern wireless communication systems. The antenna structure is consistent with 11‐unit cells of composite right–left‐hand (CRLH) ...inclusions mounted on an FR4 substrate. Therefore, the antenna size is miniaturized effectively to 30 × 20 mm2 to cover the frequency bands around 2.45 GHz, for Wi‐Fi, and 4.2–6 GHz, for sub‐6 5G, networks. The design process is conducted on a circuit model and numerical simulations by evaluating the unit cell transmission phase spectra. For this, a comparison between the circuit model and the numerical simulations is invoked for validation. Such an antenna is found to provide a maximum gain of 6.2 dBi at 4.6 GHz. Next, 11 PIN diodes control the current motion between the antenna patch and the CRLH array. Therefore, PIN arrays are connected to the patch and the ground plane to maintain the surface current motion that realizes main lobe beam steering. The proposed antenna performance is simulated numerically using the CSTMWS software package. Then, it is fabricated and tested experimentally for validation. An excellent agreement is achieved between the simulated and measured results. Finally, it is found this antenna provides excellent beam steering −92° to 92° to suit many modern networks.
In this work, a highly miniaturized microstrip antenna array based on two elements is proposed for multiple inputs multiple outputs (MIMO) application systems at sub-6 GHz frequency bands. The ...antenna is structured from a meander line in conjugate with an interdigital capacitor when excited through the monopole basic antenna. The proposed antenna elements are separated with a Minkowski factor-shaped metamaterial (MTM) column to achieve a separation distance (D) of 0.08λ at 3 GHz when printed on an FR-4 substrate. Later on, the antenna performance in terms of bandwidth and gain is controlled using a photonic process based on optical active switches based on light-dependent resistances (LDR). Therefore, the reconfiguration complexity with such a technique can be eliminated significantly without the need for a biasing circuit. The antenna design was conducted through several parametric studies to arrive at the optimal design that realizes the frequency bandwidth between 3 and 5.5 GHz with a maximum gain of about 4.5 dBi when all LDR terminals are off. For a wireless channel performance study-based massive MIMO environment, the proposed antenna is suitable to be configured in arrays of 64 × 64 elements. From this study, it was found the maximum bit error rate (BER) does not exceed 0.15 with a channel capacity (CC) of 2 Gbps. For validation, the antenna was fabricated based on two elements and tested experimentally. Finally, it was revealed that the measured results agree very well with simulations after comparing the theoretical calculations with the measured data.
This paper presents a microwave sensor based on a two-ports network for liquid characterizations. The proposed sensor is constructed as a miniaturized microwave resonator based on Moore fractal ...geometry of the 4th iteration. The T-resonator is combined with the proposed structure to increase the sensor quality factor. The proposed sensor occupies an area of 50 × 50 × 1.6 mm3 printed on an FR4 substrate. Analytically, a theoretical study is conducted to explain the proposed sensor operation. The proposed sensor was fabricated and experimentally tested for validation. Later, two pans were printed on the sensor to hold the Sample Under Test (SUT) of crude oil. The frequency resonance of the proposed structure before loading SUT was found to be 0.8 GHz. After printing the pans, a 150 MHz frequency shift was accrued to the first resonance. The sensing part was accomplished by monitoring the S-parameters in terms of S12 regarding the water concentration change in the crude oil samples. Therefore, 10 different samples with different water percentages were introduced to the proposed sensor to be tested for detecting the water content. Finally, the measurements of the proposed process were found to agree very well with their relative simulated results.
A microstrip highly sensitive differential sensor for complex permittivity characterization of urine samples was designed, fabricated and tested. The sensing area contains two pairs of open-stub ...resonators, and the working frequency of the unloaded sensor is 1.25 GHz. The sensor is easily implemented on an affordable substrate FR-4 Epoxy with a thickness of 1.6 mm. A Teflon beaker is mounted on the sensor without affecting the measurements. Numerically, liquid mixtures of water and urine at different percentages were introduced to the proposed sensor to evaluate the frequency variation. The percentage of water content in the mixture varied from 0% (100% urine) to 100% (0% urine) with a step of 3.226%, thus giving 32 data groups of the simulated results. Experimentally, the mixtures of: 0% urine (100% water), 20% urine (80% water), 33% urine (66% water), 50% urine (50% water), 66% urine (33% water), and 100% urine (0% water) were considered for validation. The complex permittivity of the considered samples was evaluated using a nonlinear least square curve fitting in MATLAB in order to realize a sensing sensitivity of about 3%.
In this paper, a moderate gain monopole antenna is proposed for GSM and Wi-Max applications. The antenna structure is constructed from a traditional printed monopole on Roger substrate of 3006 ...family. To enhance the antenna performance ultimately, an Electromagnetic Band Gap (EBG) layer is introduced to the antenna structure. A numerical analysis is applied based on a Finite Integral Technique (FIT) of CST Microwave Studio (CSTMWS) formulations to characterize the EBG unit cell in terms of S-parameters, dispersion and reflection diagram, as well as the constitutive electromagnetic properties. The antenna performance is tested numerically with and without the EBG structure in terms of S-parameters and radiation patterns. It is found that the proposed antenna provides an excellent matching, S
11
< −10 dB, at 1.85 and 3.3 GHz with 2.88 dBi and 5.8 dBi gain, respectively. Nevertheless, the Finite Element Method (FEM) based on Ansoft High Frequency Structure Simulator (HFSS) software package is invoked to compute the antenna performance. The antenna structure is fabricated and tested experimentally. Finally, an excellent agreement is found between the obtained numerical results from both software packages and measurements.
The p53 tumor suppressor protein induces apoptosis in response to genotoxic and environmental stresses. Recent studies have revealed the existence of a transcription-independent mitochondrial p53 ...apoptotic pathway; however, the mechanism that regulates its translocation to the mitochondria has been unknown. In this study, we show that the tumor suppressor Tid1 forms a complex with p53 under hypoxic conditions that directs p53 translocation to the mitochondria and the subsequent initiation of the mitochondrial apoptosis pathway. Loss of Tid1 expression abrogated p53 translocation to the mitochondria and inhibited apoptosis, whereas the over-expression of Tid1 promoted p53 mitochondrial localization and apoptosis. Tid1's mitochondrial signal sequence and DnaJ domain were both required for the movement of the p53-Tid1 complex from the cytosol to the mitochondria. When Tid is over-expressed in cancer cell lines expressing mutant p53 isoforms defective in transcriptional activity, mitochondrial localization and pro-apoptotic activities of the mutant p53 proteins was restored. Our results establish Tid1 as a novel regulator of p53-mediated apoptosis, and suggest that therapies designed to enhance Tid1's function in promoting mitochondrial localization of p53 and apoptosis could be an effective therapy in many cancers.
The permittivity of a material is an important parameter to characterize the degree of polarization of a material and identify components and impurities. This paper presents a non-invasive ...measurement technique to characterize materials in terms of their permittivity based on a modified metamaterial unit-cell sensor. The sensor consists of a complementary split-ring resonator (C-SRR), but its fringe electric field is contained with a conductive shield to intensify the normal component of the electric field. It is shown that by tightly electromagnetically coupling opposite sides of the unit-cell sensor to the input/output microstrip feedlines, two distinct resonant modes are excited. Perturbation of the fundamental mode is exploited here for determining the permittivity of materials. The sensitivity of the modified metamaterial unit-cell sensor is enhanced four-fold by using it to construct a tri-composite split-ring resonator (TC-SRR). The measured results confirm that the proposed technique provides an accurate and inexpensive solution to determine the permittivity of materials.
A novel design of a reconfigurable MIMO antenna array of a 3D geometry-based solar cell integration that is operating at sub-6 GHz for self-power applications in a 5G modern wireless communication ...network. The proposed antenna array provides three main frequency bands around 3.6 GHz, 3.9 GHz, and 4.9 GHz, with excellent matching impedance of S
≤ -10 dB. The proposed MIMO array is constructed from four antenna elements arranged on a cubical structure to provide a low mutual coupling, below -20 dB, over all frequency bands of interest. Each antenna element is excited with a coplanar waveguide (CPW). The proposed radiation patterns are controlled with two optical switches of Light Dependent Resistors (LDRs). The proposed antenna array is fabricated and tested experimentally in terms of S-parameters, gain and radiation patterns. The maximum gain is found to be 3.6 dBi, 6.9 dBi, and 3.5 dBi at 3.6 GHz, 3.9 GHz, and 4.9 GHz, respectively. It is realized that the proposed array realizes a significant beam forming by splitting the antenna beam and changing the main lobe direction at 3.9 GHz after changing LDR switching statuses. Such an antenna array is found to be very applicable for femtocell wireless communication networks in the 5G systems.
PDF
