Narodna in univerzitetna knjižnica, Ljubljana (NUK)
-
Površinska hrapavost akrilatnih materialov = Surface roughness of acrylic resin materialsKuhar, MilanBackground: A rough denture base surface promotes adhesion of microorganisms and plaque formation. A smooth acrylic surface is achieved by polishing. The polishability of individual acrylic resin ... materials is an important factor influencing the surface roughness of the denture base. The objective of this study was to compare the surface roughness and porosity of three different acrylic resins before and after polishing. Material and methods: Using contactprofilometric measurements and scanning electron microscopy, the surface texture of 81 specimens of autopolymerizing, heat-polymerizing and injected acrylic resin were studied after polymerization on glass, cutting with a tungsten carbide bur, and polishing with three different polishing techniques. Mean surface roughness (Ra) values for each specimen group were analyzed using two-way ANOVA and the Scheffe post-hoc test. Results: The highest mean surface roughness value was measured for surfaces finished with atungsten carbide bur. The lowest surface roughness values were determined forspecimens polished with a lathe and polishing paste. Surface roughness was influenced mainly by the finishing and polishing procedure and to a lesser extent by the acrylic resin material. The presence of large pores and rough surfaces was characteristic of autopolymerizing resin specimens. Conclusions: The surface of autopolymerizing resin is very likely to remain porous and consequently rougher than the surface of heat-polymerizing resin even after adequate polishing.Vir: Zobozdravstveni vestnik. - ISSN 0044-4928 (Letn. 61, št. 4/5, 2006, str. 151-158)Vrsta gradiva - članek, sestavni delLeto - 2006Jezik - slovenskiCOBISS.SI-ID - 22727641
Avtor
Kuhar, Milan
Teme
Acrylic Resins |
Dental Polishing |
Materials Testing |
Porosity |
Akrilne smole |
Materiali, testiranje |
Poroznost |
Zob, poliranje |
zobozdravstvo |
zobni materiali |
akrilati |
površina |
hrapavost
Vnos na polico
Trajna povezava
- URL:
Faktor vpliva
Dostop do baze podatkov JCR je dovoljen samo uporabnikom iz Slovenije. Vaš trenutni IP-naslov ni na seznamu dovoljenih za dostop, zato je potrebna avtentikacija z ustreznim računom AAI.
Leto | Faktor vpliva | Izdaja | Kategorija | Razvrstitev | ||||
---|---|---|---|---|---|---|---|---|
JCR | SNIP | JCR | SNIP | JCR | SNIP | JCR | SNIP |
Baze podatkov, v katerih je revija indeksirana
Ime baze podatkov | Področje | Leto |
---|
Povezave do osebnih bibliografij avtorjev | Povezave do podatkov o raziskovalcih v sistemu SICRIS |
---|---|
Kuhar, Milan | 10745 |
Vir: Osebne bibliografije
in: SICRIS
Izberite prevzemno mesto:
Prevzem gradiva po pošti
Naslov za dostavo:
Med podatki člana manjka naslov.
Storitev za pridobivanje naslova trenutno ni dostopna, prosimo, poskusite še enkrat.
S klikom na gumb "V redu" boste potrdili zgoraj izbrano prevzemno mesto in dokončali postopek rezervacije.
S klikom na gumb "V redu" boste potrdili zgoraj izbrano prevzemno mesto in naslov za dostavo ter dokončali postopek rezervacije.
S klikom na gumb "V redu" boste potrdili zgoraj izbrani naslov za dostavo in dokončali postopek rezervacije.
Obvestilo
Trenutno je storitev za avtomatsko prijavo in rezervacijo nedostopna. Gradivo lahko rezervirate sami na portalu Biblos ali ponovno poskusite tukaj kasneje.
Gesla v Splošnem geslovniku COBISS
Izbira mesta prevzema
Gradivo iz matične enote je brezplačno. Če je gradivo na mesto prevzema dostavljeno iz drugih enot, lahko knjižnica to storitev zaračuna.
Mesto prevzema | Status gradiva | Rezervacija |
---|
Rezervacija v teku
Prosimo, počakajte trenutek.
Rezervacija je uspela.
Rezervacija ni uspela.
Rezervacija...
Članska izkaznica:
Mesto prevzema:
Naročanje gradiva za izposojo v čitalnice
Naročanje kopij člankov
Urnik dostave gradiva z oznako DS v signaturi