An experimental study of combustion in diffusion and coaxial mesoscale burner arrays was conducted. To that end, different linear and planar arrangements were tested, and blow-off limits, flame ...geometry, and oscillations parameters were determined. The new results of the experiments showed that the coaxial burner arrays, in general, are characterized by leaner values of the blow-off limit compared to premixed flames. Moreover, the large planar arrangement (square 5 × 5) provides the global blow-off equivalence ratio value of about 0.1 at low thermal power operating modes (less than 2 kW). All arrays of coaxial jets feature flame separation into small coaxial flamelets. However, linear coaxial arrangements provide complete flame separation, whereas jets of a planar array are not fully separated and merged in pairs. At the equivalence ratio value less than 0.45, separated flames start oscillating strongly until the blow-off occurs, that is unacceptable in terms of combustion efficiency, pollutant emission, and related parameters. Therefore, the most favorable operating modes correspond to the equivalence ratio ranging from 0.45 to 0.6.
This paper presents the results of liquid-fuel model combustor calculations based on different numerical approaches to the development of a verified simulation method of combustor operation. Both ...steady and transient studies were carried using various RANS turbulent models and the detached eddy simulation (DES) method. The results of these studies were compared with experimental data obtained by optical methods. The largest differences between experiment and calculations are observed for the near-axial flow field where recirculation backflow is formed. This vortex structure can be properly resolved in a DES simulation and in transient calculations based on the SAS SST model. The use of the above-mentioned approaches in combination with the flamelet combustion model provides maximum accuracy in predicting the parameters of reacting swirling flow, in particular the velocity and temperature distributions in the combustor.
The results of numerical simulation of convective heat transfer under coaxial jet impinging on a surface are presented. The effect of jet's peripheral component swirling on the heat transfer ...enhancement by changing the number of tangential nozzles for creating jet is analyzed.
The results of particle image velocimetry near the perforated leading edge of the nozzle vane of gas turbine are presented. Visualization of the formation of cooling film on the surface of the blade ...with determination of its thickness is carried out. On the basis of the obtained results, the influence of the blown cooling air mass flow rate on the formation of the film is analyzed.
The paper considers issues related to droplet fragmentation in air flow. We present the results of calculating the equilibrium conditions for a rotating droplet. The shape of the droplet is assumed ...to be ellipsoidal, and the flow is potential. The droplet equilibrium is determined by the balance of pressure due to the surface tension force, the centrifugal force and the aerodynamic effect force of the flow. We obtained an analytic expression linking the equilibrium values of the Weber number, the ellipsoid aspect ratio and the dimensionless swirl parameter. The calculation results showed that droplet swirling has a significant effect on the equilibrium conditions in a narrow range of variation in the ellipsoid aspect ratio. We obtained critical values of the Weber number and the aspect ratios for which the equilibrium state of the droplet becomes unstable.
Numerical simulation of gas dynamics and combustion in coaxial swirled lifted propane-air jets under buoyancy conditions is performed. Dependences of dimensionless flame length L/d0, lift-off height ...h/d0 as well as flame front surface area Sfl and mass rate of burn-out U on orientation angle θ are obtained. The results of numerical simulation and experiment for different values of θ are compared. It is confirmed that in the angle range of 30° < θ < 60° flame has the smallest surface area that provides the highest value of the mass rate of burn-out. The numerical solution closest to an experiment data can be obtained by using an additional differential transport equation for the ignition time or setting a delay time in the range of 0.05..0.25 s.
Two different types of ejectors used for pumping gas, liquid and two-phase flows, as well as for evacuation of enclosed spaces have been analyzed. The results of CFD simulation of Dubinsky's Vortex ...ejector operation process are presented. The results of numerical simulation and experiment for different modes of ejector operation for passive flow and total back pressure are compared.
This paper gives a brief review of studies by Russian and foreign scientists in the field of heat and mass transfer in swirling flows; the vortex effect; swirling and vortex flows in the elements of ...gas turbine, aerospace, and power engineering; combustion with a swirling flow; and modern methods for the numerical and experimental study of swirling flows, surface vortex generators, heat transfer, and hydrodynamics on macro-, micro-, and nanoscales. The results of these studies were discussed during the seventh conference
Heat and Mass Transfer and Hydrodynamics in Swirling Flows
.
The main ways of cleaning the fuel injectors and the circuits of jet and vortex ejectors used for pumping gas, liquid and two-phase media, as well as for evacuation of enclosed spaces are analyzed. ...The possibility of organizing the process of pumping the liquid out of the fuel injection manifold secondary circuit using a vortex ejector is shown experimentally. The regimes of manifold evacuation at various inlet liquid pressure values are studied. The technology of carbon cleaning fuel injectors using a washing liquid at various working process parameters is tested.
Feasibility of using oxidant vortex reverse flow in designing jet burners for prospective combustion chambers fueled with synthesis gas. A complex of experimental studies of the reverse flow burner ...module fueled with methane with addition of synthesis gas is carried out; steady combustion concentration range is defined.
PDF
