A conceptual design is presented of a novel energy-recovering linac (ERL) facility for the development and application of the energy recovery technique to linear electron accelerators in the ...multi-turn, large current and large energy regime. The main characteristics of the powerful energy recovery linac experiment facility (PERLE) are derived from the design of the Large Hadron electron Collider, an electron beam upgrade under study for the LHC, for which it would be the key demonstrator. PERLE is thus projected as a facility to investigate efficient, high current (HC) (>10 mA) ERL operation with three re-circulation passages through newly designed SCRF cavities, at 801.58 MHz frequency, and following deceleration over another three re-circulations. In its fully equipped configuration, PERLE provides an electron beam of approximately 1 GeV energy. A physics programme possibly associated with PERLE is sketched, consisting of high precision elastic electron-proton scattering experiments, as well as photo-nuclear reactions of unprecedented intensities with up to 30 MeV photon beam energy as may be obtained using Fabry-Perot cavities. The facility has further applications as a general technology test bed that can investigate and validate novel superconducting magnets (beam induced quench tests) and superconducting RF structures (structure tests with HC beams, beam loading and transients). Besides a chapter on operation aspects, the report contains detailed considerations on the choices for the SCRF structure, optics and lattice design, solutions for arc magnets, source and injector and on further essential components. A suitable configuration derived from the here presented design concept may next be moved forward to a technical design and possibly be built by an international collaboration which is being established.
The Linac Coherent Light Source II (LCLS-II) is a new state-of-the-art coherent X-ray source being constructed at SLAC National Accelerator Laboratory. It employs 280 superconducting radio frequency ...(SRF) cavities in order operate in continuous wave (CW) mode. To reduce the overall cryogenic cost of such a large accelerator, nitrogen-doping of the SRF cavities is being used. Nitrogen-doping has consistently been shown to increase the efficiency of SRF cavities operating in the 2.0 K regime and at medium fields (15–20 MV/m) in vertical cavity tests and horizontal cryomodule tests. While nitrogen-doping’s efficacy for improvement of cavity performance was demonstrated at three independent labs, Fermilab, Jefferson Lab, and Cornell University, transfer of the technology to industry for LCLS-II production was not without challenges. Here we present results from the beginning of LCLS-II cavity production. We discuss qualification of the cavity vendors and the first cavities from each vendor. Finally, we demonstrate that nitrogen-doping has been successfully transferred to SRF cavity vendors, resulting in consistent production of cavities with better cryogenic efficiency than has ever been achieved for a large-scale accelerator.
The treatment of flue gases from power plants and municipal or industrial wastewater using electron beam irradiation technology has been successfully demonstrated in small-scale pilot plants. The ...beam energy requirement is rather modest, on the order of a few MeV; however, the adoption of the technology at an industrial scale requires the availability of high beam power, of the order of 1 MW, in a cost effective way. In this article we present the design of a compact superconducting accelerator capable of delivering a cw electron beam with a current of 1 A and an energy of 1 MeV. The main components are an rf-gridded thermionic gun and a conduction cooledβ=0.5ellipticalNb3Sncavity with dual coaxial power couplers. An engineering and cost analysis shows that the proposed design would result in a processing cost competitive with alternative treatment methods.
The higher efficiency of superconducting radio-frequency (SRF) cavities compared to normal-conducting ones enables the development of high-energy continuous-wave linear accelerators (linacs). Recent ...progress in the development of high-qualityNb3Snfilm coatings along with the availability of cryocoolers with high cooling capacity at 4 K makes it feasible to operate SRF cavities cooled by thermal conduction at relevant accelerating gradients for use in accelerators. A possible use of conduction-cooled SRF linacs is for environmental applications, requiring electron beams with energy of 1–10 MeV and 1 MW of power. We have designed a 915 MHz SRF linac for such an application and developed a prototype single-cell cavity to prove the proposed design by operating it with cryocoolers at the accelerating gradient required for 1 MeV energy gain. The cavity has a∼3μmthickNb3Snfilm on the inner surface, deposited on a∼4mmthick bulk Nb substrate and a bulk∼7mmthick Cu outer shell with three Cu attachment tabs. The cavity was tested up to a peak surface magnetic field of 53 mT in liquid He at 4.3 K. A horizontal test cryostat was designed and built to test the cavity cooled with three Gifford-McMahon cryocoolers. The rf tests of the conduction-cooled cavity, performed at General Atomics, achieved a peak surface magnetic field of 50 mT and stable operation was possible with up to 18.5 W of rf heat load. The peak frequency shift due to microphonics was 23 Hz. These results represent the highest peak surface magnetic field achieved in a conduction-cooled SRF cavity to date and meet the requirements for a 1 MeV energy gain.
Energy recovery linear accelerators (ERLs) rely upon single-axis superconducting radio frequency (SRF) cavities to be an efficient source of relativistic electrons for high energy and nuclear ...physics. SRF cavities are also considered relevant for next-generation photon factories and radio-isotope production facilities. The ultimate energy recovery capability for the accelerator would be the ability to operate with a sufficiently spent beam and decrease the energy of the beam before the beam dump to a value lower than the beam injection energy. This is especially important for high current accelerators, where the beam injection energy could be as high as several MeV, and systems where partial beam loss can be expected. The efficient operation of energy recovery in linear accelerators is adversely affected by the typical degradation of the beam quality and current loss. This hinders the application of the ERLs in research and industry, and enabling the use of spent (partially lost current), degraded beams should broaden their application. We suggest that the use of the asymmetric operating mode observed in the dual-axis asymmetric cavities will enable such ultimate capabilities. We discuss the advantages of the application of fields of different amplitude along the cavity accelerating and decelerating axes and demonstrate that the fields can be tuned separately in each axis of the dual-axis cavity. The design of such a cavity and ways to optimize the energy recovery of a spent electron beam by tuning the dual-axis asymmetric SRF cavity are discussed.
Abstract MYRRHA at SCK CEN in Mol/Belgium will be a pre-industrial large-scale Accelerator Driven System for unparalleled research opportunities in spent nuclear fuel, nuclear medicine, and ...fundamental and applied physics. In 2018 the Belgian government released funding for MYRRHA’s first phase, MINERVA, for a staged implementation and operation. It covers the design, construction, and commissioning of the continuous-wave superconducting RF proton linac up to 100 MeV, as well as dedicated user target stations. The MINERVA proton linac will accommodate 30 identical cryomodules to boost the beam energy delivered by the normal-conducting frontend from 16.6 MeV to 100 MeV. Each cryomodule will contain two superconducting RF single-spoke cavities immersed in a superfluid Helium bath at 2 K. The design and architecture of the associated cryogenic system is derived from the stringent linac reliability requirements imposed by the future subcritical nuclear reactor. We present the architecture, design, and development status of the MINERVA cryomodules and associated cryogenic system towards the implementation phase of the project as part of a collaboration between ACS, CEA/DSBT, IJCLab, and SCK CEN. We also provide an overview of the initial outcomes of cryogenic and RF tests for the prototype MINERVA cryomodule, which are still ongoing at IJCLab.
Start to end simulations for the BESSY FEL project Abo-Bakr, M; Hartrott, M.v; Knobloch, J ...
Nuclear instruments & methods in physics research. Section A, Accelerators, spectrometers, detectors and associated equipment,
08/2004, Letnik:
528, Številka:
1
Journal Article
Recenzirano
BESSY plans to construct a FEL multi user facility for the Soft-X-Ray spectral range from
20
eV
to
1
keV
. Central part of the project is a superconducting linac, based on the TESLA technology but ...operating in CW mode. A photo injector and a bunch compression scheme is introduced, allowing to reach the required electron beam parameters at the undulators beginning: up to
4
kA
peak current (
1
nC
bunch charge),
1.5π
mm
mrad
normalized transverse emittance and an energy spread below 1%. Extensive Start to End (S2E) simulations have been performed, using the programs ASTRA for the injector part, ELEGANT for the linac and bunch compression studies and GENESIS for the FEL process. Results of these simulations are presented and discussed.
The higher efficiency of superconducting radio-frequency (SRF) cavities compared to normalconducting ones enables the development of high-energy continuous-wave linear accelerators (linacs). Recent ...progress in the development of high-quality Nb3Sn film coatings along with the availability of cryocoolers with high cooling capacity at 4 K makes it feasible to operate SRF cavities cooled by thermal conduction at relevant accelerating gradients for use in accelerators. A possible use of conduction-cooled SRF linacs is for environmental applications, requiring electron beams with energy of 1 10 MeV and 1 MW of power. We have designed a 915 MHz SRF linac for such an application and developed a prototype single-cell cavity to prove the proposed design by operating it with cryocoolers at the accelerating gradient required for 1 MeV energy gain. The cavity has a ~ 3 μm thick Nb3Sn film on the inner surface, deposited on a ~ 4 mm thick bulk Nb substrate and a bulk ~ 7 mm thick Cu outer shell with three Cu attachment tabs. The cavity was tested up to a peak surface magnetic field of 53 mT in liquid He at 4.3 K. A horizontal test cryostat was designed and built to test the cavity cooled with three Gifford-McMahon cryocoolers. The rf tests of the conduction-cooled cavity, performed at General Atomics, achieved a peak surface magnetic field of 50 mT and stable operation was possible with up to 18.5 W of rf heat load. The peak-to-peak frequency shift due to microphonics was 26 Hz. These results represent the highest peak surface magnetic field achieved in a conduction-cooled SRF cavity to date and meet the requirements for a 1 MeV energy gain.
Superconducting RF guns for FELs Janssen, D; Büttig, H; Evtushenko, P ...
Nuclear instruments & methods in physics research. Section A, Accelerators, spectrometers, detectors and associated equipment,
08/2004, Letnik:
528, Številka:
1
Journal Article
Recenzirano
This paper provides an overview of the advantages and problems of superconducting RF guns. The results of the Rossendorf experiments are presented here. These results are integrated in the design of ...a new 3.4 cell superconducting RF gun. The beam parameters of this gun correspond to the demands for the new generation of high current, high brightness injectors.
Development of a superconducting radio frequency photoelectron injector Arnold, A.; Büttig, H.; Janssen, D. ...
Nuclear instruments & methods in physics research. Section A, Accelerators, spectrometers, detectors and associated equipment,
07/2007, Letnik:
577, Številka:
3
Journal Article
Recenzirano
A superconducting radio frequency (RF) photoelectron injector (SRF gun) is under development at the Research Center Dresden–Rossendorf. This project aims mainly at replacing the present thermionic ...gun of the superconducting electron linac ELBE. Thereby the beam quality is greatly improved. Especially, the normalized transverse emittance can be reduced by up to one order of magnitude depending on the operating conditions. The length of the electron bunches will be shortened by about two orders of magnitude making the present bunchers in the injection beam line dispensable. The maximum obtainable bunch charge of the present thermionic gun amounts to 80
pC. The SRF gun is designed to deliver also higher bunch charge values up to 2.5
nC. Therefore, this gun can be used also for advanced facilities such as energy recovery linacs (ERLs) and soft X-ray FELs. The SRF gun is designed as a
3
1
2
cell cavity structure with three cells basically TESLA cells supplemented by a newly developed gun cell and a choke filter. The exit energy is projected to be 9.5
MeV. In this paper, we present a description of the design of the SRF gun with special emphasis on the physical and technical problems arising from the necessity of integrating a photocathode into the superconducting cavity structure. Preparation, transfer, cooling and alignment of the photocathode are discussed. In designing the SRF gun cryostat for most components wherever possible the technical solutions were adapted from the ELBE cryostat in some cases with major modifications. As concerns the status of the project the design is finished, most parts are manufactured and the gun is being assembled. Some of the key components are tested in special test arrangements such as cavity warm tuning, cathode cooling, the mechanical behavior of the tuners and the effectiveness of the magnetic screening of the cavity.