The aim of this work was to determine the changes in the chemical and physical-mechanical properties of gauze compresses under the influence of various sterilizations. Gauze compresses are made of ...cotton; therefore, all methods used focused on cotton. The methods used to test possible damage to cotton materials (pH value (pH paper, KI starch paper), yellowing test, Fehling reaction, reaction to the formation of Turnbull blue (Berlin blue), microscopic staining with methylene blue and swelling reaction with Na-zincate) did not show that the sterilizations affected the cotton compresses. The morphological characteristics were examined with a scanning electron microscope (SEM). The SEM images showed that there were no morphological changes in the cotton fibers. FTIR-ATR spectroscopy revealed that the sterilization processes did not alter the characteristic bands of the cotton. The length of the macromolecules was increased (DP), showing that the sterilization processes had affected the cotton. The results of the wet strength test followed. The samples showed values below 100%, with the exception of two samples. It is known from theory that the relative wet strength is less than 100% when the material is damaged. The t-test performed on the strength results showed that the p-value was greater than 0.05 for all samples tested, with the exception of one sample. The degree of swelling capacity was determined, with non-sterilized samples having the highest capacity, followed by samples sterilized with ethylene oxide and then samples sterilized by steam sterilization. The results obtained are a contribution to the innovation of the topic of this work and a scientific confirmation for manufacturers and anyone interested in the influence of the sterilization process on natural fibers (cotton).
The modification of cellulose woven fabrics and viscose nonwovens was carried out with the aim of preparing sustainable coatings from biodegradable natural polymers. The modification of fabrics with ...biodegradable natural polymers represents an ecological alternative to other textile modifications, such as the sol-gel process. Coatings were prepared from erythritol, gelatin, and collagen in various formulations with the addition of propolis and alginate fibers and a natural plasticizer (glycerin). The morphology of the materials was determined before and after modification with Dino-Lite. Moreover, the pH value, the drop test method, the angle recovery angle, the thickness, and the mass per unit area were monitored before and after modification. The results have shown that modifications had no significant effect on the thickness or mass per unit area. In contrast, in a larger proportion, they show hydrophilic properties, which favor their application for medical purposes—for example; for the absorption of exudates in wound dressings; etc. In addition, due to the neutral and slightly alkaline pH values of the modified samples, they can be suitable for external application on the skin. The results of the recovery angle of the modified samples proved that the samples did not tend to crease and that they retained their elasticity after modification with a very pleasant textile feel (fabric hand), making them even more suitable for everyday applications.
The aim of this study was to prepare and characterize thin hybrid films on polyurethane-coated knitted fabrics and to achieve satisfactory color fastness to artificial light. Sol–gel-derived hybrid ...thin films were deposited via the dip-coating of 3-glycidoxypropiltrimethoxysilane. Titanium dioxide (TiO2) and zinc oxide (ZnO) nanopowders were added to compensate for the insufficient aging resistance, which manifests itself in low color fastness and is one of the most frequent complaints from manufacturers of coated marine fabrics (yachts, boats, etc.). The optimum processing conditions were determined by varying the concentration of precursors and auxiliaries, the mass concentration of TiO2 and ZnO nanopowders, the drawing speed, and the methods and process of fabric treatment. The hybrid films were also characterized using scanning electron microscopy and Fourier transform infrared spectroscopy with attenuated total internal reflection, while Spectraflash SF 300 investigated color fastness. After 300 h of exposure in a xenon chamber, the thin hybrid films showed good color fastness and good resistance to washing cycles. The sol–gel treatment proved to be a successful answer to the manufacturers’ need for the post-treatment of polyurethane-coated knitted fabrics against UV radiation for use in the marine sector (yachts, speedboats, etc.).
Electrospun filaments represent a new generation of medical textiles with promising applications in soft tissue repair. A potential strategy to improve their design is to combine them with bioactive ...molecules. Curcumin, a natural compound found in turmeric, is particularly attractive for its antioxidant, anti-inflammatory, and antimicrobial properties. However, investigating the range of relevant doses of curcumin in materials designed for tissue regeneration has remained limited. In this paper, a wide range of curcumin concentrations was explored and the potential of the resulting materials for soft tissue repair applications was assessed. Polydioxanone (PDO) filaments were prepared with various amounts of curcumin: 0%, 0.001%, 0.01%, 0.1%, 1%, and 10% (weight to weight ratio). The results from the present study showed that, at low doses (≤0.1%), the addition of curcumin has no influence on the spinning process or on the physicochemical properties of the filaments, whereas higher doses lead to smaller fiber diameters and improved mechanical properties. Moreover, filaments with 0.001% and 0.01% curcumin stimulate the metabolic activity and proliferation of normal human dermal fibroblasts (NHDFs) compared with the no-filament control. However, this stimulation is not significant when compared to the control filaments (0%). Highly dosed filaments induce either the inhibition of proliferation (with 1%) or cell apoptosis (with 10%) as a result of the concentrations of curcumin found in the medium (9 and 32 μM, respectively), which are near or above the known toxicity threshold of curcumin (~10 μM). Moreover, filaments with 10% curcumin increase the catalase activity and glutathione content in NHDFs, indicating an increased production of reactive oxygen species resulting from the large concentration of curcumin. Overall, this study suggested that PDO electrospun filaments loaded with low amounts of curcumin are more promising compared with higher concentrations for stimulating tissue repair. This study also highlighted the need to explore lower concentrations when using polymers as PDO, such as those with polycaprolactone and other degradable polyesters.
In this work the in vitro antimicrobial activity of colloidal solutions of nine different commercially available nanoparticles were investigated against
strains, both methicillin-sensitive (MSSA) and ...methicillin-resistant (MRSA). Research covered antimicrobial investigation of different metal and metal-oxide nanoparticles, including Ag 10 nm, Ag 40 nm, Al
O
100 nm, Au 20 nm, Pt 4 nm, TiO
100 nm, Y
O
100 nm, ZnO 100 nm and ZrO
100 nm nanoparticles. Such materials were foreseen to be applied as coatings on 3D-printed biodegradable polymers: i.e., catheters, disposable materials, hospital bedding items, disposable antimicrobial linings and bandages for chronic wounds. Therefore, the antimicrobial activity of the nanoparticles was determined by agar well diffusion assays and serial microdilution broth assays. In addition, the chromatographic characterization of elements present in trace amounts was performed as a method for tracing the nanoparticles. Moreover, the potential of preparing the rough surface of biodegradable polymers for coating with antimicrobial nanoparticles was tested by 3D-printing fused deposition methodology. The in vitro results have shown that particular nanoparticles provided powerful antimicrobial effects against MSSA and MRSA strains, and can be easily applied on different biopolymers.
The development of antimicrobial polymers is a priority for engineers fighting microbial resistant strains. Silver ions and silver nanoparticles can assist in enhancing the antimicrobial properties ...of microcapsules that release such substances in time which prolongs the efficiency of antimicrobial effects. Therefore, this study aimed to functionalize different polymer surfaces with antimicrobial core/shell microcapsules. Microcapsules were made of sodium alginate in shell and filled with antimicrobial silver in their core prior to application on the surface of polymer materials by dip-coating methodology. Characterization of polymers after functionalization was performed by several spectroscopic and microscopic techniques. After the characterization of polymers before and after the functionalization, the release of the active substances was monitored in time. The obtained test results can help with the calculation on the minimal concentration of antimicrobial silver that is encapsulated to achieve the desired amounts of release over time.
Silver (Ag) and zinc (Zn) are very powerful antimicrobial metals. Therefore, in this research, a high-throughput, sensitive, and rapid method was developed for the determination of Ag and Zn in ...microcapsules using inductively coupled plasma mass spectrometry (ICP-MS). The sample preparation procedure employed simple microwave digestion of the microcapsules with 55.55%
/
HNO
and 44.45%
/
H
O
. The method was applied to determine Ag and Zn in microcapsule samples of different sizes (120 and 450 μm) after their preparation with and without chitosan. Prepared microcapsules, after characterization, were bonded to a polymer carrier by sol-gel procedure and the materials were characterized by FTIR spectroscopy and high-resolution optical microscopy. Significant differences were found in Ag and Zn levels between microcapsules samples prepared with and without chitosan. The results have shown that samples with chitosan had up to 20% higher levels of Zn than Ag: 120 μm microcapsules contained 351.50 μg/g of Ag and 85.51 μg/g of Zn, respectively. In contrast, samples prepared without chitosan showed larger overall variability: In microcapsules with a diameter of 120 μm, the amounts of antimicrobial metals were 98.32 μg/g of Ag and 106.75 μg of Zn, respectively. Moreover, 450 μm microcapsules contained 190.98 μg/g of Ag and 121.35 μg/g of Zn. Those quantities are high enough for efficient antimicrobial activity of newly prepared microcapsules, enabling the application of microcapsules in different antimicrobial coatings.
Sol-gel postupak jedan je od novih i potpuno drugačijih pristupa u površinskoj modifikaciji tekstilnih materijala, te se smatra jednim od najvažnijih otkrića znanosti o materijalima i inženjerstva ...materijala posljednjih desetljeća. U području tekstilne tehnologije sol-gel postupak pruža velike mogućnosti u pogledu osmišljavanja i stvaranja novih površinskih svojstava tekstilija s obzirom na prilagodljivost i postizanje ciljanih modifikacija kombiniranjem različitih anorganskih i organskih polaznih materijala. Takve kombinacije mogu rezultirati potpuno novim, višefunkcionalnim svojstvima tekstilija poput tekstilnih materijala za posebnu namjenu, tj. za zaštitu od statičkog elektriciteta. Takva modifikacija ima vrlo važno značenje budući da se njezinom uspješnom provedbom štiti najvrednije – ljudski život.
Modifikacijom standardiziranih metoda ispitivanja netkanog tekstila koje nisu namijenjene za pelene, imajući istodobno na umu neke propise proizvođača pelena, osmišljena je i izarađena aparatura za ...ispitivanje učinkovitosti pelena. Optimirani su uvjeti ispitivanja kojima se u određenoj mjeri simuliraju uvjeti primjene pelena
PDF
