A digital-to-time converter (DTC) controls time delay by a digital code, which is useful, for example, in a sampling oscilloscope, fractional-N PLL, or time-interleaved ADC. This paper proposes ...constant-slope charging as a method to realize a DTC with intrinsically better integral non-linearity (INL) compared to the popular variable-slope method. The proposed DTC chip realized in 65 nm CMOS consists of a voltage-controlled variable-delay element (DTC-core) driven by a 10 bit digital-to-analog converter. Measurements with a 55 MHz crystal clock demonstrate a full-scale delay programmable from 19 ps to 189 ps with a resolution from 19 fs to 185 fs. As available oscilloscopes are not good enough to reliably measure such high timing resolution, a frequency-domain method has been developed that modulates a DTC edge and derives INL from spur strength. An INL of 0.17% at 189 ps full-scale delay and 0.34% at 19 ps are measured, representing 8-9 bit effective INL-limited resolution. Output rms jitter is better than 210 fs limited by the test setup, while the DTC consumes 1.8 mW.
High linearity CMOS radio receivers often exploit linear V-I conversion at RF, followed by passive down-mixing and an OpAmp-based Transimpedance Amplifier at baseband. Due to nonlinearity and finite ...gain in the OpAmp, virtual ground is imperfect, inducing distortion currents. This paper proposes a negative conductance concept to cancel such distortion currents. Through a simple intuitive analysis, the basic operation of the technique is explained. By mathematical analysis the optimum negative conductance value is derived and related to feedback theory. In- and out-of-band linearity, stability and Noise Figure are also analyzed. The technique is applied to linearize an RF receiver, and a prototype is implemented in 65 nm technology. Measurement results show an increase of in-band IIP 3 from 9 dBm to >20 dBm, and IIP2 from 51 to 61 dBm, at the cost of increasing the noise figure from 6 to 7.5 dB and <;10% power penalty. In 1 MHz bandwidth, a Spurious-Free Dynamic Range of 85 dB is achieved at <;27 mA up to 2 GHz for 1.2 V supply voltage.
A discrete-time (DT) mixing architecture for RF-sampling receivers is presented. This architecture makes RF sampling more suitable for software-defined radio (SDR) as it achieves wideband quadrature ...demodulation and wideband harmonic rejection. The paper consists of two parts. In the first part, different downconversion techniques are classified and compared, leading to the definition of a DT mixing concept. The suitability of CT-mixing and RF-sampling receivers to SDR is also discussed. In the second part, we elaborate the DT-mixing architecture, which can be realized by de-multiplexing. Simulation shows a wideband 90° phase shift between I and Q outputs without systematic channel bandwidth limitation. Oversampling and harmonic rejection relaxes RF pre-filtering and reduces noise and interference folding. A proof-of-concept DT-mixing downconverter has been built in 65 nm CMOS, for 0.2 to 0.9 GHz RF band employing 8-times oversampling. It can reject 2nd to 6th harmonics by 40 dB typically and without systematic channel bandwidth limitation. Without an LNA, it achieves a gain of -0.5 to 2.5 dB, a DSB noise figure of 18 to 20 dB, an IIP3 = +10 dBm, and an IIP2 = +53 dBm, while consuming less than 19 mW including multiphase clock generation.
A multiband flexible RF-sampling receiver aimed at software-defined radio is presented. The wideband RF sampling function is enabled by a recently proposed discrete-time mixing downconverter. This ...work exploits a voltage-sensing LNA preceded by a tunable LC pre-filter with one external coil to demonstrate an RF-sampling receiver with low noise figure (NF) and high harmonic rejection (HR). The second-order LC filter provides voltage pre-gain and attenuates the source noise aliasing, and it also improves the HR ratio of the sampling downconverter. The LNA consists of a simple amplifier topology built from inverters and resistors to improve the third-order nonlinearity via an enhanced voltage mirror technique. The RF-sampling receiver employs 8 times oversampling covering 300 to 800 MHz in two RF sub-bands. The chip is realized in 65 nm CMOS and the measured gain across the band is between 22 and 28 dB, while achieving a NF between 0.8 to 4.3 dB. The IIP2 varies between +38 and +49 dBm and the IIP3 between -14 dBm and -9 dBm, and the third and fifth order HR ratios are more than 60 dB. The LNA and downconverter consumes 6 mW, and the clock generator takes 12 mW at 800 MHz RF.
An integrated spectrum analyzer is useful for built-in self-test purposes, software-defined radios, or dynamic spectrum access in cognitive radio. The analog/RF performance is impaired by a number of ...factors, including thermal noise, phase noise, and nonlinearity. In this paper, we present an integrated circuit with two integrated RF-frontends, of which the outputs are crosscorrelated in digital baseband. We show by theory and measurements that the above-mentioned impairments are mitigated by this technique. The presented 65-nm CMOS prototype operates at 1.2 V, and obtains a noise floor below -169 dBm/Hz, an IIP 3 of +25 dBm, and more than 20 dB of phase-noise reduction. In a special high-impedance mode, an even lower noise floor below -172 dBm/Hz is obtained.
Dynamic transmission gate (DTG) flip-flops (FFs) (DTG-FFs) and current mode logic (CML) FFs (CML-FFs) are compared targeting power efficient multiphase clock generation with low phase error. The ...effect of component mismatches on multiphase clock timing inaccuracies is modeled and compared, using the product of mismatch-induced jitter variance and power consumption as a figure-of-merit (FOM). Analytical equations are derived to estimate the jitter-power FOM for DTG-FF- and CML-FF-based dividers. Simulations confirm the trends predicted by the equations and show that DTG-FFs achieve a better FOM than CML-FFs. The advantage increases for CMOS processes with smaller feature size and for a lower input frequency compared to fT.
A software-defined radio (SDR) receiver with improved robustness to out-of-band interference (OBI) is presented. Two main challenges are identified for an OBI-robust SDR receiver: out-of-band ...nonlinearity and harmonic mixing. Voltage gain at RF is avoided, and instead realized at baseband in combination with low-pass filtering to mitigate blockers and improve out-of-band IIP3. Two alternative ¿iterative¿ harmonic-rejection (HR) techniques are presented to achieve high HR robust to mismatch: a) an analog two-stage polyphase HR concept, which enhances the HR to more than 60 dB; b) a digital adaptive interference cancelling (AIC) technique, which can suppress one dominating harmonic by at least 80 dB. An accurate multiphase clock generator is presented for a mismatch-robust HR. A proof-of-concept receiver is implemented in 65 nm CMOS. Measurements show 34 dB gain, 4 dB NF, and + 3.5 dBm in-band IIP3 while the out-of-band IIP3 is +16 dBm without fine tuning. The measured RF bandwidth is up to 6 GHz and the 8-phase LO works up to 0.9 GHz (master clock up to 7.2 GHz). At 0.8 GHz LO, the analog two-stage polyphase HR achieves a second to sixth order HR > 60 dB over 40 chips, while the digital AIC technique achieves HR > 80 dB for the dominating harmonic. The total power consumption is 50 mA from a 1.2 V supply.
A digital-to-time converter (DTC) produces a time delay based on a digital code. Similar to data converters, linearity is a key metric for a DTC and it can be characterized by its integral ...nonlinearity (INL). However, measuring the INL of a subpicosecond-resolution DTC is problematic, even when using the best available high-speed oscilloscopes. In this brief we propose a new method to measure the INL of a DTC by applying digital phase modulation and measuring the output spectrum with a spectrum analyzer. The frequency selectivity of this method allows for an improved measurement resolution down to a few femtoseconds and allows measuring an INL below 100 fs. The proposed method is verified by behavioral simulations and is employed to measure the INL of a high-resolution DTC realized in the 65-nm CMOS, with a time resolution of 25 fs and a standard deviation of 27 fs.
PDF
